2 1 3 4 5 6 14 7 13 12 11 10 9 www.blackanddecker.co.
English 2 (Original instructions) 5
13 15 16 8 17 9 19 26 6 18 7 20 4 10 a b c 7 21 22 23 1 3
18 24 24 7 4
Intended use Your Black & Decker inflation station is designed to be used cordless or, in most vehicles, from the standard 12 Vdc socket, to inflate car and bike tyres, balls, rafts, air mattresses and swimming pool floats etc. This product is intended for household, consumer use only.
Additional safety instructions for batteries and chargers Batteries Never attempt to open for any reason. Do not expose the battery to water. Do not expose the battery to heat. Do not store in locations where the temperature may exceed 40°C. Charge only at ambient temperatures between 10°C and 40°C. Charge only using the charger provided with the appliance/tool. When disposing of batteries, follow the instructions given in the section "Protecting the environment".
Plug the AC charger (13) into the mains power supply. The LED (15) on the AC charger (13) will indicate the level of charging. Red, unit charging, Green, unit charged. When fully charged, remove the AC charger from the mains and remove the jack plug from the unit. Note: Store your AC charger in a safe place for later use. Place the inflation needle or tapered nozzle into the item to be inflated. Note: Always make sure that the lever is in the up position when not in use.
Quick start Warning! Never leave the inflator running unattended in this mode. It can burst car tyres and other items. To use your inflator immediately, you can do so without setting the automatic shut-off feature: Switch the main power switch (1) to the inflate position (c, fig E). To switch between the different units (PSI, BAR or KPA) press the - & + buttons (21 and 23) together until the required units are displayed.
Insert the hose (with accessories if required) to the item to be inflated. To start the pump press the power switch (22) on the LCD. When the item is inflated as required or to stop the pump at any time press the power switch (22) on the LCD. Remove the hose from the item and store it on the unit. Turn the main power switch (1) to the off position (b fig. E). To deflate using the high-volume pump (i.
Remove the fuse. Fit a new fuse of the same type and size (8A/250V). Refit the cap and centre pin. Tighten the cap by turning clockwise onto the plug. Protecting the environment Separate collection. This product must not be disposed of with normal household waste. Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.
TYP. ASI500 H1-H2 Partial support - Only parts shown available Nur die aufgefuerten teile sind lieferbar Reparation partielle - Seules les pieces indiquees sont disponibles Supporto parziale - Sono disponibili soltanto le parti evidenziate Solo estan disponibles las peizas listadas So se encontram disponiveis as pecas listadas Gedeeltelijke ondersteuning - alleen de getoonde onderdelen zijn beschikbaar 2 1 3 4 6 7 5 E15803 www.2helpU.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country. Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD 90564180 REV 0 Tel.
