User Manual

10/100Base-TX Hardened PoL/PoE Ethernet Extender, Black Box Part Number LBPS310A-KIT (includes one LBPS311A and one LBPS312A)
2 V1
Power Input Assignment
Power1
48 VDC
DC Jack
Power2
＋
T: 46-57 VDC
R: 46-57 VDC
Terminal
Block
－
Power Ground
Power3
＋
T: 46-57 VDC
R: 46-57 VDC
－
Power Ground
Earth Ground
DIP
Switch
Down
Up
Transmitter
PoL
Disable Power over Link
Enable Power over Link
Type
Std (Standard)
Standard line speed
Better noise immunity
Per (Performance)
Better line speed
Poor noise immunity
Receiver
Mode
Loc (Local), Set Receiver
to Local Mode
Rmt (Remote), Set
Receiver to Remote Mode
Type
Std (Standard)
Standard line speed
Better noise immunity
Per (Performance)
Better line speed
Poor noise immunity
LEDs
State
Indication
Power 1/2/3
Steady
Power received
Off
Power off
PoL
Steady
Power Ethernet extension interface function is enabled
Off
No power is transmitted over Ethernet extension interface
PoE
Steady
Powered device (PD) is connected
Off
Powered device (PD) is disconnected
Link
Steady
A valid Extender connection established
Fast Flashing
Data transmission or receiving
Slow Flashing
Extender port under negotiation mode
Off
Extender interface connection is not established
Line Speed
Steady
Displays the link speed in Mbps
PSE Output
Steady
PoE power can be transmitted for PD
All off
No PoE power can be transmitted for PD
Green
Steady
A valid Ethernet connection established
Flashing
Data transmission or receiving
Off
Non-Ethernet connection is established
Yellow
Steady
Link speed at 100Mbps
Off
Link speed at 10Mbps
Power over Link (PoL) Enabled
Distance
Data Rate
Receiver PoE
Output
300M
100Mbps
30.0 W
400M
90Mbps
15.4 W
600M
60Mbps
14.0 W
800M
45Mbps
9.5 W
1000M
35Mbps
7.0 W
1200M
20Mbps
5.0 W
Power over Link (PoL) Disabled
Power Supply Applied on Receiver
Distance
Data
Rate
Receiver PoE Output
1400 M
15M bps
30.0 W
1600 M
10 Mbps
30.0 W
1800 M
3 Mbps
30.0 W
Up to 2200
M
1Mbps
30.0 W
<Note> The Reference Performance is tested on 24AWG Telephone wire (0.5mm diameter, 1-pair
wire, Cable impedance: 100ohm).
10/100Base-TX and Ethernet Extender Connectors
10/100Base-TX Connection
The following lists the pinouts of
10/100Base-TX RJ-45 port.
Pin
Regular Port
PoE Port
1
Output Transmit Data +
Output Transmit Data +
2
Output Transmit Data -
Output Transmit Data -
3
Input Receive Data +
Input Receive Data +
4
Positive (VCC+)
5
Positive (VCC+)
6
Input Receive Data -
Input Receive Data -
7
Negative (VCC-)
8
Negative (VCC-)
Ethernet Extender Connection
RJ-11 and Terminal Block port pinouts:
Pin 3: Tip, Pin 4: Ring.
Use a telephone line to connect two RJ-11 or
Ter m i na l Bl o c k ports between two Hardened
Ethernet Extenders.
Functional Description
• Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial
environment.
• Ethernet port: Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,
full/half-duplex; Auto MDI/MDIX.
• Auto data rate negotiation for Ethernet extension interface.
• Six speeds with speed indicator LEDs on front panel of unit, up to 100 Mbps @ about 300
meters (984 ft.), down to 1 Mbps @ about 2,200 meters (7,218 ft.).
• Supports Power over Ethernet application up to 1,200 meters (3,937 ft.) for Max. 5 watts
power consumed by PoE powered devices.
• Power consumption:
- Enable Power over Link (PoL) function: Max. 65 Watts
- Disable Power over Link (PoL) function: Transmitter: Max. 5 W
Receiver: Max. 35 W with PoE output
Max. 5 W without PoE output.
• Power Supply: Redundant T: 46-57 V, R: 46-57 VDC Terminal Block power inputs and 48
VDC Latched DC JACK interface.
• Operating temperature range @ -40℃ to 75℃ (-40℉ to 167℉). Tested for functional
operation
@ -40℃ to 85℃ (-40℉ to 185℉).
• Supports Din-Rail or Panel Mounting installation.