User Manual

Page 17
877-877-2269 | BlackBox.com
Chapter 3: RS-232 Connection
IDX Function Command Response Parameters Desription Example
16 Get Input EDID
Status
GET EDID_
STATUS[CR/LF]
VGA EDID: prm[CR/
LF]
DP EDID: prm[CR/LF]
HDMI1 EDID:
prm[CR/LF]
HDMI2 EDID:
prm[CR/LF]
VGA: prm={fix0, fix1, fix2, fix3,
fix4}
fix0: 1280x800@60Hz
fix1: 1920x1200@60Hz
fix2: 1920x1080@60Hz
fix3: 1280x720@60Hz
fix4: 1024x768@60Hz
DP/HDMI1/HDMI2:
prm={fix0, fix1, fix2, fix3, fix4,
fix5, fix6, fix7}
fix0: copy
fix1: 4K@30Hz 2CH
fix2: 1920x108060Hz
fix3: 1280x720@60Hz
fix4: 1920x1200@60Hz
fix5: 1280x800@60Hz
fix6: 1920x1080@60Hz Dolby 5.1
Command: GET EDID_STATUS[CR/LF]
Response:
VGA EDID: fix0[CR/LF]
DP EDID: fix2[CR/LF]
HDMI1 EDID: fix2[CR/LF]
HDMI2 EDID: fix2[CR/LF]
17 Volume Gain
Adjust
SET VOLGAIN_DATA
aout prm[CR/LF]
VOLGAIN_DATA aout
prm[CR/LF]
VOLGAIN is volgain
aout = {audioout};
prm = {0~100
Command: SET VOLGAIN_DATA audioout
50[CR/LF]
Response: VOLGAIN_DATA audioout
50[CR/LF]
18 Audio Mute cmd SET MUTE aout
prm[CR/LF]
MUTE aout prm[CR/
LF]
aout = {audioout};
prm = {on, off}// on means mute;
off means not audio mute
Command: SET MUTE audioout on [CR/LF]
Response: MUTE audioout on [CR/LF]
19 Set Output
Resolution
SET RESOLUTION out
prm[CR/LF]
RESOLUTION out
prm[CR/LF]
prm = {3840x2160@30,
1920x1200@60, 1920x1080@60,
1600x1200@60, 1366x768@60,
1280x1024@60, 1280x720@60,
1280x800@60, 1024x768@60,
auto}
out = {hdmiout};
Command: SET RESOLUTION hdmiout
auto[CR/LF]
Response: RESOLUTION hdmiout auto[CR/
LF]
20 Set Standby on/
off
SET STANDBY_
ONOFF prm[CR/LF]
STANDBY_ONOFF
prmCR/LF]
prm = {on, off} Command: SET STANDBY_ONOFF on[CR/
LF]
Response: STANDBY_ONOFF on [CR/LF]
21 Get Scaler Mode
Status
GET SCALER_
STATUS[CR/LF]
Scaler Info:
STANDBY_status
prm1[CR/LF]
RESOLUTION
hdmiout prm2[CR/LF]
HDCP hdmiout
prm1[CR/LF]
MUTE audioout
prm1[CR/LF]
VOLGAIN_DATA
audioout prm3[CR/
LF]
prm1 = {on, off}
prm2={3840x2160@30,
1920x1200@60, 1920x1080@60,
1600x1200@60, 1366x768@60,
1280x1024@60, 1280x720@60,
1280x800@60, 1024x768@60,
auto}
prm3={0-100}
Command: GET SCALER_STATUS[CR/LF]
Response: Scaler Info:
STANDBY_status off[CR/LF]
RESOLUTION hdmiout auto[CR/LF]
HDCP hdmiout on[CR/LF]
MUTE audioout off[CR/LF]
VOLGAIN_DATA audioout 35[CR/LF]
22 Factory Reset RESET[CR/LF] / / Command: RESET[CR/LF]
23 System Reboot REBOOT[CR/LF] / / Command: REBOOT[CR/LF
24 Get System
Status
GET SYS_
STATUS[CR/LF]
Response all system
status information
/ Command: GET SYS_STATUS[CR/LF]
Response:
...
Response all system status information
25 Upgrade Module UPG[CR/LF] Enter ICP Mode...
[CR/LF]
/ Command: UPG CR/LF]
Response: Enter ICP Mode.....[CR/LF]