Switch User Manual
724-746-5500 | blackbox.com
Page 154
LGB5028A User‘s Manual
724-746-5500 | blackbox.com
Chapter 6: Configuration
“x”: Deletes the QCE.
“+”: The lowest plus sign adds a new entry at the bottom of the QCE listings.
Port Members: Check the box next to any port to make it a member of the QCL entry. By default all ports will be checked.
Key Parameters: Key configurations are described below:
Tag Value of Tag field can be “Any,” “Untag,” or “Tag.”
VID Valid value of VLAN ID can be any value in the range 1–4095 or ”Any.” Users can enter either a specific value or a range of
VIDs.
PCP Priority Code Point: Valid value PCP are specific (0, 1, 2, 3, 4, 5, 6, 7) or range (0–1, 2–3, 4–5, 6–7, 0–3, 4–7) or “Any.”
DEI Drop Eligible Indicator: Valid value of DEI can be any of values between 0–1 or “Any.”
SMAC: Source MAC address: 24 MS bits (OUI) or “Any.”
DMAC Type: Destination MAC type: possible values are unicast (UC), multicast (MC), broadcast (BC) or “Any.”
Frame Type: Frame Type can have any of the following values:
1. Any
2. Ethernet
3. LLC
4. SNAP
5. IPv4
6. IPv6
NOTE: All frame types are explained below:
1. Any: Allow all types of frames.
2. Ethernet: Valid Ethernet type are within 0x600–0xFFFF or “Any.” The default value is “Any.”
3. LLC: SSAP Address Valid SSAP (Source Service Access Point) can vary from 0x00 to 0xFF or “Any'.” The default value is “Any.”
DSAP Address Valid DSAP (Destination Service Access Point) can vary from 0x00 to 0xFF or “Any.” The default value is “Any.”
Control Address Valid Control Address can vary from 0x00 to 0xFF or “Any.” The default value is “Any.”
4. SNAP: PID Valid PID (a.k.a Ethernet type) can have value within 0x00–0xFFFF or “Any.” The default value is “Any.”
5. IPv4: Protocol IP protocol number: (0–255, TCP or UDP) or ”Any.” Source IP Specific Source IP address in value/mask format or
“Any.” IP and Mask are in the format x.y.z.w, where x, y, z, and w are decimal numbers between 0 and 255. When Mask is
converted to a 32-bit binary string and read from left to right, all bits following the first zero must also be zero DSCP Diffserv
Code Point value (DSCP): It can be specific value, range of value, or “Any.” DSCP values are in the range 0–63, including BE, CS1–
CS7, EF, or AF11–AF43. IP Fragment IPv4 frame fragmented option: yes|no|any
Sport Source TCP/UDP port: (0–65535) or “Any,” specific or port range applicable for IP protocol UDP/TCP.Dport Destination TCP/
UDP port:(0-65535) or “Any,” specific or port range applicable for IP protocol UDP/TCP.
6. IPv6: Protocol IP protocol number: (0–255, TCP or UDP) or “Any” Source IP IPv6 source address: (a.b.c.d) or “Any,” 32 LS bits
DSCP Diffserv Code Point value (DSCP): It can be specific value, range of value, or “Any.” DSCP values are in the range 0–63
including BE, CS1-CS7, EF, or AF11–AF43.
Sport Source TCP/UDP port: (0–65535) or “Any,” specific or port range applicable for IP protocol UDP/TCP.Dport Destination TCP/
UDP port:(0-65535) or “Any,” specific, or port range applicable for IP protocol UDP/TCP.