LPBG716A LPBG724A 16-/24-Port Gigabit PoE PSE Web Smart Switch with 4 SFP Slots Bring PoE into your Gigabit network. Models available with sixteen or twenty-four autosensing, auto-negotiating 10-/100-/1000-Mbps ports; four are dual-media ports, which may be used for copper or fiber (SFPs).
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Caution Circuit devices are sensitive to static electricity, which can damage their delicate electronics. Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge. To protect your device, always: ∞Touch the metal chassis of your computer to ground the static electrical charge before you pick up the circuit device. ∞Pick up the device by holding it on the left and right edges only.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Federal Communications Commission and Industry Canada Radio Frequency Interference Statements This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Normas Oficiales Mexicanas (NOM) Electrical Safety Statement INSTRUCCIONES DE SEGURIDAD 1. 2. 3. 4. 5. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch European Community (CE) Electromagnetic Compatibility Directive This equipment has been tested and found to comply with the protection requirements of European Emission Standard EN55022/EN61000-3 and the Generic European Immunity Standard EN55024. EMC: EN55022 (2003)/CISPR-2 (2002): class A IEC61000-4-2 (2001): 4KV CD, 8KV AD IEC61000-4-3 (2002): 3V/m IEC61000-4-4 (2001):1KV (power line), 0.5KV (signal line) 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 1. Specifications 1.1 Hardware Specifications Certifications: FCC Class A, CE Flow Control: IEEE802.3x compliant for full duplex; Backpressure flow control for half duplex Full Forwarding/Filtering Packet Rate: PPS (packets per second) Forwarding Rate 148,8000PPS 148,800PPS 14,880PPS Speed 1000Mbps 100Mbps 10Mbps Standards Compliance: IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3z 1000BASE-T, IEEE 802.3x Flow Control, IEEE 802.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 1.2 Management Software Specifications Port Management: Port Configuration, Port Mirroring, Broadcast Strom Control, PoE On/ Off Setting VLAN Setting: Port-based/Tag-based, VLAN ID: 1–4094K Trunking: 2 groups (1–4 ports for each group) VLAN Function: Port-Base/802.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 2. Overview 2.1 Features Supports the following: - Real-time status (link, speed, duplex) of each port - Port setting for enable or disable operation (the 1st port can’t be disabled) - Pport setting for N-Way or force mode operation - Broadcast Storm Protection - Port-based VLAN - Priority queues for QoS 2.2 What’s Included Your package should include the following items.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Rear Panel AC Power Input Figure 2-3. LPBG716A or LPBG724A Rear Panel. 2.4 LED Indicators Figure 2-4. LED Indicators on the LPBG724A.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 3. Installation 3.1 Hardware and Cable Installation CAUTION: Wear a grounding device to avoid damage from electrostatic discharge. Be sure that the power switch is OFF before you connect the power cord to the power source. 3.1.1 TP Port and Cable Installation 1.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch SFP transceiver module Figure 3-1. 3.1.3 Power On The switch supports a 100–240 VAC, 50–60 Hz power supply. The power supply will automatically convert the local AC power source to DC power. It does not matter whether or not any connection is plugged into the switch when powering on. After the power is on, all LED indicators will light up and then all will turn off, except for the power LED, which stays on. 3.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 3-2 Install the switch chassis in a 19"rack 3.3 Cabling Requirement For successful installation and good network performance, use CAT5, CAT5e, or higher cable. If you use non-compliant cables, the LAN will work poorly. For a Fast Ethernet TP network connection, the grade of the cable must be CAT5 or CAT5e with a maximum length of 328 feet (100 meters). 3.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch The sum of all elements’ bit-time delay and the overall bit-time delay of wires/devices must be within the required Round Trip Delay (bit times) in a half-duplex network segment (collision domain). For full-duplex operation, this does not apply. 3.5 Set IP Address, Subnet Mask, and Default Gateway IP Address First, configure your PC IP address or change the IP address of the switch. Next, change the default gateway’s IP address and subnet mask.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 3-5. Login Screen for Web. Page 14 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4. Web-based Management Operation This chapter instructs you how to configure and manage the switch through the Web user interface it supports. You can access and monitor the switch’s status, including port activity, spanning tree status, port aggregation status, VLAN, and priority status and so on from any one port on the switch. The default values of the managed switch are listed in the table below: IP Address: 192.168.2.1 Subnet Mask: 255.255.
/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.1 Web Management Home Overview After you login, you can select one of the configurations by clicking the icon in the configuration bar. There are four major categories for your configuration. - Configuration Monitoring Maintenance Logout 4.2 Configuration 4.2.1 System The System Configuration screen shows system status, including: MAC address, system firmware version, and so on.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.2.2 Ports You can enable or disable Jumbo Frames by clicking it in the check box. Select the “Port no.” that you want to configure for the mode below: - Auto speed - enable/disable the port - 10M/100M/1000M - full/half-duplex - enable/disable flow control Figure 4-3. Ports configuration. 4.2.3 VLANs There are 16 VLAN groups. Select and add a group into “VLAN ID” and then click the port number that you want to put into the selected VLAN group.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 4-4. VLAN configuration. 4.2.4 Aggregation Set up port trunk groups and then click the port number you want to include in the same group. Choose from eight groups. The maximum for one group is 24 ports. Figure 4-5. Aggregation/ Trunk configuration. 4.2.5 LACP To enable/disable the protocol for a port, select the port number. Page 18 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 4-6. LACP Port configuration. 4.2.6 RSTP To enable/disable the protocol for a port, select the port number. 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 4-7 RSTP configuration 4.2.7 802.1x Select the “Port no.” that you want to configure for the mode below: - Auto - Force Authorized - Force Unauthorized Figure 4-8. 802.1x configuration. Page 20 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.2.8 IGMP You can enable or disable IGMP by clicking the checking box. Select the “Port no.” for which you want to configure the mode. Figure 4-9. IGMP configuration. 4.2.9 Mirroring Port Mirroring mirrors the traffic from the Source port to the Destination port. Select the Destination port from port 1 to port 24, and then select the Source port by clicking the corresponding checkbox. Figure 4-10. Port Mirroring configuration.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.2.10 Quality of Service You can enable or disable QoS by clicking the checkbox. If you enable QoS, you can select the class of service for each port. Figure 4-11. QoS configuration. 4.2.11 Filter Select the “Port no.” for which you want to enable/disable the filtering IP address. Figure 4-12. Filter configuration. Page 22 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.2.12 Rate Limit Select the “Port no.” for which you want to configure the speed. Figure 4-13. Rate Limit configuration. 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.2.13 Storm Control You can set up storm control by configuring the modes. Figure 4-14. Storm Control configuration. Page 24 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.3 Monitoring 4.3.1 Statistics Overview The screen below shows statistics for all ports. Figure 4-15. Statistics Overview for all ports. 4.3.2 Detail Statistics For detailed statistics of each port, click the port number. Figure 4-16. Detailed Statistics for all ports. 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.3.3 LACP Status The screen below shows the LACP status for LACP ports. Figure 4-17. LACP Aggregation overview. 4.3.4 RSTP Status The screen below shows RSTP status for RSTP ports. Figure 4-18. RSTP VLAN Bridge overview. Page 26 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.3.5 IGMP Status The screen below shows IGMP status for IGMP ports. Figure 4-19. IGMP Status. 4.3.6 VeriPHY Click the port number(s) and the mode to see VeriPHY cable status for a port(s). Figure 4-20 VeriPHY Cable Diagnostics 4.3.7 Ping Choose the mode to select the target IP address. 724-746-5500 l www.blackbox.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 4-21. Ping Parameters. 4.4 Maintenance 4.4.1 Warm Restart You can select yes/no to do the warm restart, and then the new settings will change according to your selection. Figure 4-22. Warm Restart. 4.4.2 Factory Default You can select yes/no to perform a Factory Default, and then the new settings will change according to your selection. Figure 4-23. Factory Default. 4.4.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 4-24. Software Upload. 4.4.4 Configuration File Transfer Follow the instructions on the screen to upload and download the configuration. Figure 4-25. Configuration Upload and Download. 4.4.5 PoE Remotely access and monitor the attached PD (Powered Device) status by using the Enable/Disable function. 1. Enable: PoE of the port is able to supply power to the attached PD (Powered Device). 2.
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 4-26. PoE. 4.4.6 Logout Click “Logout” to logout of the switch. 4.4.7 Forgot Password If you forgot your IP or password, use the reset button for the factory default setting first. Then take the following steps to reset the Web Smart Switch back to the original default: Step 1: Turn on the Web Smart Switch. Step 2: Press and hold the reset button continuously for 15 seconds then release the reset button.
LPBG716A, rev. 1 ______________________________________________________________________ 724-746-5500 l www.blackbox.
