Instruction manual

ManualsBrandsBKI ManualsConvection OvenMT-200

CONTROL AND INDICATOR MODULE

S2000-BKI

INSTRUCTION MANUAL

1 GENERAL TECHNICAL DATA

1.1. GENERAL

1.1.1 S2000-BKI Control and Indicator Module (hereinafter referred to as the module) is designed

to operate as a part of an ORION ISS, under a network controller, along with such devices as

Signal-10, Signal-20, Signal-20М, Signal-20P, S2000-4, S2000-KDL, etc. The network controller

can be either S2000M fire and alarm console of version 2.03+ or a PC with installed ORION Pro

software. Also the module can perform some functions under S2000 fire and alarm console

(displaying statuses of only intrusion and fire partitions).

1.1.2 The module provides light and sound indication of statuses of assigned ORION ISS

partitions as well as arming and disarming the partitions by pressing module’s buttons.

1.1.3 The module is to be mounted inside the premises and is destined for round-the-clock

operation.

1.1.4 The module must not be used in aggressive medium or dust condition, or in explosion-

hazardous premises.

1.2 SPECIFICATION







Light Indication

- 60 bicolor LEDs to display statuses of up to 60

partitions of an ORION ISS, and

- 7 single color LEDs to display alarms and troubles in

the assigned partitions as a whole, and

- A LED to display module’s status (READY), and

- A LED to display system reaction to users’ trying to

arm/disarm partitions (ACCESS)

 Built-in Sounder

- Yes



Tamper Switch

- Yes



485

Communication

Port

(to work as a part of Orion ISS)

- Yes



Input

Power

- (10.2 to– 28.4) V dc. We advise to use battery backed

power supplies of RIP series manufactured by the

Bolid Company

 Consumed Power

- 3 W max



Consumed

urrent

in alarm mode

in quiescent mode (all

indicators are off)

- 200 mА max at 12 V dc

- 100 mА max at 24 V dc

- 50 mА max at 12 V dc

- 50 mА max at 24 V dc

 Pre-Operation Time

- 2 s max

 Weight

- 0.6 kg max

 Programming

- By means of UProg or UProg Free Configuration Tool

 Reader Input

- 1 for a reader with Touch Memory output interface

 Ingress Protection Rating

- IР20

 Operating Temperatures

−

30 to +50

Summary of content (8 pages)

PAGE 1
CONTROL AND INDICATOR MODULE S2000-BKI INSTRUCTION MANUAL 1 GENERAL TECHNICAL DATA 1.1. GENERAL 1.1.1 S2000-BKI Control and Indicator Module (hereinafter referred to as the module) is designed to operate as a part of an ORION ISS, under a network controller, along with such devices as Signal-10, Signal-20, Signal-20М, Signal-20P, S2000-4, S2000-KDL, etc. The network controller can be either S2000M fire and alarm console of version 2.03+ or a PC with installed ORION Pro software.
PAGE 2
1.3 1) 2) 3) 4) STANDARD DELIVERY S2000-BKI Control and Indicator Module Instruction Manual Woodscrew and Wall Plug 6х30 Package Front View: Rear View: Two holes to attach the module on the wall Two holes to pass the cables Figure 1. View, Overall and Mounting Dimensions 2 – 1 pcs. – 1 pcs. – 4 pcs. – 1 pcs.
PAGE 3
2 MOUNTING AND WIRING THE MODULE 2.1. Mounting the Module 2.1.1. Mount the module at that height from the floor which is suitable to operate and maintain it. 2.1.2. The module is to be mounted on walls or other constructions of premises at places protected against atmospheric fallouts and mechanical damage. 2.1.3. Please ensure that the wall the module is to be mounted to is solid, flat, clean, and dry. 2.1.4. Mark 4 mounting places on the wall in accordance with Figure 1. 2.1.5. Drill the mounting holes.
PAGE 4
3 INSPECTING THE MODULE 3.1 To make sure your S2000-BKI module keeps proper operability, it must be inspected by a competent specialist at least on receipt and annually. 3.2 Inspect the module at following ambient conditions: − The relative humidity 45% through 80%; − The ambient temperature 15°C through 35°C; − The atmospheric pressure 630 mm Hg through 800 mm Hg. 3.3 While inspecting the module, always shut off the module’s power before connecting and disconnecting its external circuits. 3.
PAGE 5
d) LEDs «1» to «60» turn on in green, and simultaneously indicators FIRE, PREALARM, ARMING FAULT turn on in red while TROUBLE indicator turns on in yellow; e) The procedure c) is repeated, then indicators «1» - «60» turn off while single-color indicators keep flashing; f) Each LED from «1» to «60» turns on when its adjacent button is pressed. or 3.6.3 The module exits the self-diagnostic mode after pressing the SILENCE button automatically after 30 s since last pressing on a module’s button.
PAGE 6
5 5.1 MODULE OPERATING MODES Indication Modes 5.1.1 Table 2 displays behavior of the module’s READY LED depending on module’s statuses. Table 2. READY Indicator Behavior Module Status Norm No connection over the RS-485 interface bus Programming (updating the firmware) READY Indicator Behavior Lit steady Flashes twice per second Flashes four times per second 5.1.
PAGE 7
Arming Request Disarming Request Blinks in green and yellow alternately four times per second 5.1.4 The system indicators FIRE, PREALARM, INTRUSION, PANIC ALARM, ARMING FAULT, OFFLINE, and TROUBLE displays alarms and troubles of various types which have just been occurred in the part of the Orion ISS assigned to the S2000-BKI. This LEDs flash in phase with LED of the partitions having relevant statuses.
PAGE 8
Disarming Short-time pressing on a button when the assigned partition is in one of the statuses: Armed, Arming Failed, Intrusion Alarm, Fire Prealarm, Fire Alarm Arming Short-time pressing on a button when the assigned partition is in the Disarmed status 5.3.3 For free access to arming/disarming partitions the module should be assigned to an Access Code (it can be programmed by UProg or UProgFree). The module transfers this code to the network controller upon pressing any of the buttons «1» to «60».