Specifications

ManualsBrandsBK Radio ManualsGadgetsDPH- CMD

Keypad Programming Manual 1

TABLE OF CONTENTS

How To Program Radios ................................................................................2

Keypad Programming ....................................................................................2

A. Navigation........................................................................................3

1. Group Parameters (CH 00) ......................................................4

2. Channel Parameters (CH 01 - CH20) .......................................4

3. Global Parameters (GRP 00)....................................................5

B. Group Parameters (CH 00)...............................................................5

1. Group Options: 1-12345678.....................................................5

2. Group Label.............................................................................6

C. Channel Parameters (CH 01 - CH20)................................................7

1. Channel Bandwidth..................................................................7

2. Receive Frequency..................................................................8

3. Receive Mode .........................................................................8

4. Receive Guard.........................................................................8

5. Receive NAC...........................................................................9

6. Squelch Mode .......................................................................10

7. Transmit Frequency...............................................................10

8. Transmit Mode.......................................................................11

9. Transmit Guard......................................................................11

10. Transmit NAC........................................................................12

11. Talk Group ID........................................................................13

12. Channel Label .......................................................................14

D. Global Parameters (GRP 00)..........................................................14

1. Keypad Programming Password ............................................14

2. Automatic Numeric Identification (ANI) ...................................15

3. Priority 1 Channel ..................................................................15

4. Priority 1 Group .....................................................................16

5. Priority 2 Channel ..................................................................16

6. Priority 2 Group .....................................................................17

7. Transmit On Priority 1 ............................................................17

8. Old-Style BK Priority Scan .....................................................17

9. Priority 1 Lock........................................................................18

10. Scan List Lock.......................................................................18

11. Transmitter Time-Out Timer ...................................................18

12. Scan Delay Time ...................................................................19

13. Busy Channel Operation........................................................19

14. ANI/DTMF Mode....................................................................20

15. Backlight Triggers..................................................................21

16. Backlight Duration..................................................................22

17. Silent Mode ...........................................................................22

18. Battery Saver.........................................................................22

19. Review Global Parameters (GRP 00) .....................................23

E. Exit Programming Mode .................................................................23

Cloning Radio Settings.................................................................................23

Tone Channel Guard Values ........................................................................26

Digital Channel Guard Values.......................................................................27

Summary of content (14 pages)

PAGE 1
TABLE OF CONTENTS How To Program Radios ................................................................................2 Keypad Programming ....................................................................................2 A. Navigation........................................................................................3 1. Group Parameters (CH 00) ......................................................4 2. Channel Parameters (CH 01 - CH20) .......................................4 3.
PAGE 2
HOW TO PROGRAM RADIOS DIGITAL CHANNEL GUARD VALUES You can program DPH-CMD radios in three different ways: Codes for the Digital Channel Guard system may be chosen from the following list. This can be done during the code programming of the system. Usually systems using direct unit to unit transmission (systems without mobile relays, repeaters, remote control, etc) may use codes from the table. Systems with relays etc. may use code variations for system control and operational efficiency.
PAGE 3
5. Release the [FCN] key and the master switch. The radio is now in the Password Entry Mode. TONE CHANNEL GUARD VALUES The Tone Channel Guard system may be set for any frequency in the range of 67 to 255.9 Hz. However, since most systems adhere to the Electronic Industry Association (EIA) standards, tones should be selected from the following EIA list.
PAGE 4
1. Group Parameters (CH 00) include: 9. Once the data to be transferred have been selected, press the [FCN] key on the Master radio keypad. The top line of the display will flash ‘CLONING’ while the program in the master is being downloaded to the clone. Group Options: 1-12345678 (1-7 = undefined, 8 = group scan list bit) 10. If the download was successful, the display on the Master will again display the clone prompt (target and data to be transferred).
PAGE 5
Master Clone NOTE: Some groups may be “locked” by PC programming to prevent them from being overwritten. Only “unlocked” groups will accept incoming clones. 3. Global Parameters (GRP 00) include: 1. Make sure the battery packs for both radios are charged. 2. Attach the master switch end of the cloning cable to the side connector of the Master radio. NOTE: One plug of the cloning cable has a push-button master switch. This plug must be attached to the Master radio. Master Switch 3.
PAGE 6
NOTE: BK Radio current drain and battery life specifications are based on performance with the battery saver on. When an option is enabled, the corresponding number in the display will flash. When the option is disabled the number is steady. If you wish to change the option from enabled to disabled or vice versa, press the number key corresponding to that option. Press [PRI] to toggle the option on or off. Press [ENT] to store the setting and advance to the next field. Options 1 Through 7 19.
PAGE 7
16. Backlight Duration PRG 6 sec BL DURATION Changing The Group Label Backlight Duration can be set for LITE OFF, 1 SEC ON, 1-second increments up to 6 SEC ON, and LITE ON. Labels are edited from left to right. Pressing the [PRI] key moves the cursor to the next character. Pressing and holding the [PRI] key backspaces to the previous character. NOTE: Excessive battery drain will result if LITE ON is set and used for extended periods of time.
PAGE 8
2. Receive Frequency PRG RX 148.00000 rx frequency Press the [ENT] key to store the changed setting and advance to the next field. Press the [FCN] key to move to the ‘RX FREQUENCY’ field. This is the receive frequency for channel 1 (in MHz). Press the [FCN] key to advance to the next field if no change is needed. 15. Backlight Triggers If the displayed frequency is correct, press the [FCN] key to advance to the next field. The backlight can be triggered by different events.
PAGE 9
Busy Channel Lockout - The yellow LED illuminates and the transmitter PTT is disabled when a signal is received without the programmed receive Channel Guard setting. PRG RX D 023 Rx Guard Busy Channel Override - This option is similar to Busy Channel Lockout except the transmitter PTT can be activated by rotating the Squelch knob clockwise off the Channel Guard detent. Press the [PRI] key to cycle through the available settings.
PAGE 10
To enter a ‘letter’ after another ‘letter’ or number, first enter any number, then toggle it with long [2] or [3] key presses. maximum of 225 seconds (3 minutes, 45 seconds). Press the [PRI] key again to change the duration from 225 seconds to zero. Press [ENT] to store and return to the next value. Press the [CLR] key to set the Time-Out Timer duration to zero. 6. Squelch Mode PRG RX NORMAL SQUELCH MODE Press the [ENT] key to store the changed setting and advance to the next field.
PAGE 11
9. Priority 1 Lock PRG USER SELECT PRI-1 SELECT Only valid frequencies will be operable. When PRI-1 SELECTION is set to LOCKED OUT, the user will not be able to change the designation of the Priority 1 Channel by selecting a channel and pressing the [PRI] key. When PRI-1 SELECTION is set to USER SELECT the user will be able to change the channel that is designated as Priority 1 Channel. Press [PRI] to toggle the option on or off.
PAGE 12
the three digit code has been entered allows the digital code to be inverted. When the displayed value is correct, press the [ENT] key to store the Channel Guard and automatically advance to the next field. 6. Priority 2 Group PRG GROUP 2 PRI-2 GROUP 10. Transmit NAC PRG TX $293 Tx nac This field is the Network Access Code (NAC) for Channel 1 transmit. This value is only used if the transmit mode selected was Digital or Mixed, or if User Channel Guard is activated.
PAGE 13
Press the [PRI] key to cycle through the priority channel options. NOTE: To enable User NAC Pick List Selection, press and hold the ‘U’ key “[8] key”. The display will show “UNAC EN”. To disable Pick List Selection, press and hold the ‘U’ key again. If Pick List Selection is enabled, but none of the entries has been selected, the radio will use the default NAC ($293) when transmitting in digital mode. Setting the channel to MAIN ties the PRI-1 channel to the Channel Selector knob.
PAGE 14
12. Channel Label PRG TX Label 18 Chan label 2. Automatic Numeric Identification (ANI) This field is the channel label for channel 1. If this label is correct press the [FCN] key to proceed to the entry point. PRG ANI 1234567 Ani id num If a new channel label is desired, follow the instructions under "Group Label" on page 6 of this manual. If no change is needed for the ID number, press the [FCN] key to advance to the next field.