Bizfon Manual II: Administrator's Guide Manual II: Administrator’s Guide Edition 1 SW Release 3.1.
Bizfon Manual II: Administrator's Guide Table of Contents Manual I: see Installation Guide Step-by-step guide to install and configure Bizfon basically Manual II: Administrator's Guide About this Administrator's Guide ................................................................................................................ 4 Bizfon’s Graphical Interface .......................................................................................................................
Bizfon Manual II: Administrator's Guide Supported SIP Phones.....................................................................................................................................51 Loopback Settings...............................................................................................................................................51 FXO Settings.............................................................................................................................................
Bizfon Manual II: Administrator's Guide About this Administrator's Guide About this Administrator's Guide The Bizfon Manual is divided into three parts: • Manual-I: Installation Guide gives step-by-step instructions to provision the Bizfon IP PBX and configure the phone extensions with the Bizfon SIP Server.
Bizfon Manual II: Administrator's Guide Bizfon's Graphical Interface Bizfon’s Graphical Interface Administrator’s Main Page As the result of logging in as an administrator, the page Bizfon Management is displayed with a table of active calls (including information about call peers, call duration and start time) at the startup. Here the administrator may access the following settings and perform the actions: Fig.
Bizfon Manual II: Administrator's Guide Bizfon's Graphical Interface Recurrent Buttons Button Description Button Description This button leads back to the previous page of a fixed sequence of pages (used mainly in wizards). This button leads back to the page you have been on before. This button takes you to the next page of a fixed sequence of pages (used mainly in wizards). This button confirms an operation you started before. This button discards the latest not yet confirmed entries.
Bizfon Manual II: Administrator's Guide Administrator's Menus Administrator’s Menus System Menu Fig. II-1: System Menu in Dynamo theme Fig. II-2: System Menu in Plain theme System Configuration Wizard The System Configuration Wizard is the helpful tool for the administrator to define the Bizfon’s Local Area Network settings and to specify regional configuration settings to make Bizfon operational in its LAN.
Bizfon Manual II: Administrator's Guide Administrator's Menus The System Configuration page contains the host name, IP address and Subnet Mask information about the Bizfon LAN interface. These settings make Bizfon available to the internal network. The System Configuration page offers the following input options: Host Name requires a host name for the Bizfon device. IP Address requires the Bizfon host address for the LAN interface. Subnet Mask requires the Bizfon hosts’ Subnet Mask. Fig.
Bizfon Manual II: Administrator's Guide Administrator's Menus Internet Configuration Wizard The Internet Configuration Wizard is the helpful tool for the administrator to configure the WAN interface settings and to adjust Bizfon’s connectivity with an external network. The Internet Configuration Wizard MUST be run if it is desired for Bizfon to be connected to the Internet.
Bizfon Manual II: Administrator's Guide Administrator's Menus Required Bandwidth for Standard Packets: Packet Size in msec. G.711u/G.711a G.726-16 Needed bandwidth in kbit/s using the Codecs: G.726-24 G.726-32 G.726-40 G.729a G723-5.3 G723-6.3 iLBC-13.
Bizfon Manual II: Administrator's Guide Administrator's Menus Status The system status window displays non-editable tables providing extensive status information about Bizfon: General Information, Network Status, Lines Status, Memory Status, Hardware Status, SIP Registration Status and MGCP Registration Status. The links on this page lead to device Transfer Statistics, user mailboxes and supplementary services configuration pages. The System Status page has several tables providing system information.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Transfer Statistics page allows a user-defined statistic table depending on the transmit/receive value (criteria), interface type and time period. It contains the following components: Time Range of statistic table - the drop down list includes the period(in days) statistics data is to be collected and the corresponding diagram charts are to be built.
Bizfon Manual II: Administrator's Guide Administrator's Menus Lines Status The page Bizfon Status - Lines Status shows the current status of each of the FXS, IP and FXO lines with all details of the attached extension. Since only one line of information can be displayed at a time, the Line, IP Line and FXO functional buttons are used to navigate through the other lines’ information. The Lines Status table displayed for FXS and IP lines include a group of static and dynamic parameters.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Lines Status table of each FXO Line gives information about the Allowed Call Types, shows the extension number (attendant or routing client), shows to whom the Incoming Call is Routed To and displays the State of the line (Free or Busy). Fig. II-17: Line Status - FXO Status page Memory Status The Memory Status page includes tables with the available User Space information for each extension.
Bizfon Manual II: Administrator's Guide Administrator's Menus SIP Registration Status The SIP registration Status is a table displaying the SIP registration status of the Bizfon extensions. The table contains a list of all the registered extensions of Bizfon, information about SIP registration states for them, addresses of SIP servers where they are registered (if so), registration date and time, as well as SIP registration names.
Bizfon Manual II: Administrator's Guide Administrator's Menus At least one route should be selected in order to use these functions, otherwise the error message appears: “No record(s) selected.” The page Add IP Static Route offers the following components: Route To requires the IP address and subnet mask of the destination the IP packet ought to be forwarded to. Via IP address requires the IP address of the subsequent router for IP packet forwarding to the specified destination.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Add VPN Route page offers the following components: Route Via contains the available PPTP and L2TP connections on the Bizfon. A connection selected from this list will be used to route the IP packet from the Bizfon’s LAN to the peer behind the PPTP/L2TP tunnel. Route To requires the IP address range of the possible peers behind the PPTP/L2TP tunnel whereto IP packets could be routed. Fig.
Bizfon Manual II: Administrator's Guide Administrator's Menus Please Note: Unlike the factory default settings restore procedure initialized from the Reset button on the Bizfon board, this link will keep the following data: • • • • • Call Statistics Transfer Statistics System Events Feature Keys Device Registration state Events The Events page shows two tables and displays all system events that have occurred in one table and event settings in the other.
Bizfon Manual II: Administrator's Guide Administrator's Menus The System Events table is the list of new and read system events. System events have the corresponding coloring depending on the nature of the event: success (priority 1, color green), low importance failure (priority 2, color yellow), critical failure (priority 3, color red).
Bizfon Manual II: Administrator's Guide Administrator's Menus Numerous circumstances may cause a certain application on Bizfon to flag an event. The page Event Settings lists all possible events on the Bizfon and allows controlling the way of notification (action), if one of those events takes place. Each entry in the events’ table has its checkbox assigned to the row. By selecting the corresponding checkboxes, operations such as Edit may be done for one or more events.
Bizfon Manual II: Administrator's Guide Administrator's Menus To Assign an Action to the Event 1. 2. 3. 4. Select the checkbox of one or more events to assign an action to them. Press the Edit button. The Edit Event Settings page appears. Select an action type from the Action radio buttons to notify the administrator about the event in the desired way. Press the Save button to submit the changes or use Back to abort the selected action.
Bizfon Manual II: Administrator's Guide Administrator's Menus Enable enables the system mail sending possibility and voice messages transmission to the extension user’s mailbox. SMTP Host requires the SMTP host IP address or domain name. The SMTP host needs to be configured to enable voice message transmission. Mail Sender Address requires the source address for the Bizfon notification emails.
Bizfon Manual II: Administrator's Guide Administrator's Menus Firmware Update This window allows to update the software of Bizfon by installing new firmware called image. To learn more about new firmware available, please contact Bizfon Technical Support. Updating a new firmware requires a perfectly working power supply. Therefore Bizfon is provided with a battery (accumulator).
Bizfon Manual II: Administrator's Guide Administrator's Menus This page displays non-editable information about the image validity. The Image Check will display invalid if the image does not correspond to the hardware version. The fields Current Software Version and New Software Version show the old software version and the version of the new image. This page needs a confirmation to continue image updating. If you are sure that the image version is appropriate for your device press Save. Fig.
Bizfon Manual II: Administrator's Guide Administrator's Menus Diagnostics The System Diagnostic page gives a possibility to run Network and WAN protocol diagnostics, to verify Bizfon's connectivity. The Start Detecting WAN Protocol button is used to initiate WAN diagnostics that will detect the WAN IP configuration: static or through DHCP and PPP servers. For static WAN IP configuration, gateway availability is checked. When acting as a client, DHCP and PPP servers' accessibilities are being verified.
Bizfon Manual II: Administrator's Guide Administrator's Menus To get a Feature Key register the Bizfon device and send a corresponding request to Bizfon's Technical Support. This request must include the Unique ID that is displayed in the Features page above the features list. Fig.
Bizfon Manual II: Administrator's Guide Administrator's Menus Enable User and Disabled User functional buttons are used to enable/disable the Local Administrator’s account. Please Note: Administrator’s account cannot be disabled. Roles page contains a table where Local Administrator and Extensions users are listed. Page allows to set the permissions to the GUI pages for each user in the table.
Bizfon Manual II: Administrator's Guide Administrator's Menus Users Menu Fig. II-49: Telephone Users Menu in Dynamo Theme F Fig. II-50: Telephone Users Menu in Plain Theme Extensions Management The Extensions Management is used to create user extensions and auto attendants on the Bizfon. From this page, by clicking on the user extension, administrator can get the extension settings pages. Two types of user extensions can be created on the Bizfon: active and inactive extensions.
Bizfon Manual II: Administrator's Guide Administrator's Menus The following columns are present in the table: • • • Extension - lists the 2-digit user or attendant extensions on the Bizfon. This number is used for internal PBX calls. • SIP Address - displays the SIP address of the corresponding extension. Column displays the full SIP address, (i.e., username@sipserver:port) when the Registration on SIP Server checkbox is selected.
Bizfon Manual II: Administrator's Guide 1. Administrator's Menus General Settings This group requires extension‘s personal information and has the following components: Display Name is an optional parameter used to recognize the caller. Usually the display name appears on the called party’s phone display whenever a call is performed or a voice mail is sent. Password requires a password for the new extension. The extension password may only contain digits.
Bizfon Manual II: Administrator's Guide Administrator's Menus 3. Advanced SIP Settings This group is used to configure advanced SIP settings (Outbound Proxy, Secondary SIP Server and Outbound Proxy for the Secondary SIP Server settings and to define other SIP server specific settings). SIP Outbound proxy is such a SIP server, where all the SIP requests and other SIP messages are transferred. Some SIP servers use an outbound proxy server to escape restrictions of NAT, e.g.
Bizfon Manual II: Administrator's Guide Administrator's Menus Enable checkbox activates the Call Queue functionality on the extension. Call Queue Size text field requires the length of the call queue, i.e. the number of calls that can be held during extension being in call. If a maximal number of calls is already held in the call queue, next incoming call will be disconnected. Max Call Queue Appearance text field requires the maximal number of active calls on the line, i.e.
Bizfon Manual II: Administrator's Guide Administrator's Menus When user dials the pickup extension having several extensions of the pickup group ringing, the first (oldest in time) call will be picked up. When user dials the pickup extension having no ringing extensions of the pickup group, “No call is available to pickup” message will be played to the user.
Bizfon Manual II: Administrator's Guide Administrator's Menus Address text field is used to define the address to be included in the Access List table. The value in this field is strictly dependent on the Call Type defined in the same named drop down list. If PBX call type is selected, the Bizfon extension number should be defined in this field. For the SIP call type, the SIP address should be defined, for the PSTN call type, the PSTN user number should be defined here.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Download Welcome Message File link appears only if a file has been previously uploaded. The link is used to download the audio file to the PC and opens the file chooser window where the saving location can be specified.
Bizfon Manual II: Administrator's Guide Administrator's Menus To Configure an Extension 1. 2. 3. 4. 5. 6. Press the Add button on the Extensions Management page. The Add Entry page will appear in the browser window. Enter the desired extension number in the Extension text field and select the extension type from the Type drop down list. Press Save to create a extension with the defined number. Select the checkbox of the newly created extension in the Extensions Management table and press Edit button.
Bizfon Manual II: Administrator's Guide Administrator's Menus Add opens the Add Entry page where the user may add codecs supported by Bizfon. The voice codec defines the voice compression algorithm for the incoming and outgoing DSP packages. Codecs lists all codecs supported by Bizfon. If no more codecs are available (all available codecs have already been transferred to the Active Codecs table), the Add Entry page will display the message “No Available Codecs” instead of the drop down menu. Fig.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Authorized Phones Database page displays the Authorized Phones Database table where the trusted phones are listed. Only SIP and PSTN users can be added to the Authorized Phones Database. The Authorized Phones Database table displays all trusted callers with their settings, e.g., call type, caller address, extension they automatically login with, information if they have automatic access to Auto Attendant (Call Relay Menu, etc.). Fig.
Bizfon Manual II: Administrator's Guide Administrator's Menus To use Instant Call Back, PSTN caller registered in the Authorized Phones Database should simply call to Bizfon’s PSTN number (that should be previously routed to the Auto Attendant or Routing Manager from the FXO Settings page) from the global PSTN network, let the call ring twice and then hang up. Call Back will get instantly activated, i.e.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Upload Universal Extension Recordings page consists of a table where universal voice messages are listed. An Upload functional link is present for each not uploaded voice message in the table and is used to upload the custom system message. When a message is uploaded, Upload functional link is replaced by Download and Remove functional links respectively used to download to the PC and to remove the uploaded system message.
Bizfon Manual II: Administrator's Guide Administrator's Menus When incoming call addressed to the certain manager comes in, receptionist can see blinking of the corresponding programmable key and the caller’s ID (for Snom360 only) on the phone’s display. Receptionist is able to intercept the incoming call by pressing the blinking key. Caller will be connected to the receptionist then.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Receptionist Phone Configuration Wizard - Page 2 is available only for Snom selection in the Phone Model drop down list on the previous page and for multiple Attached IP Lines. Page is used to set the correspondence between the selected IP lines and the available Programmable keys on the IP Phone. To do so, select the IP lines corresponding to each programmable key from the drop down list on the page. Fig.
Bizfon Manual II: Administrator's Guide Administrator's Menus Telephony Menu Fig. II-76: Telephony Menu in Dynamo Theme Fig. II-77: Telephony Menu in Plain Theme Call Statistics The Call Statistics page displays four tables and provides information on successful, unsuccessful and missed incoming and outgoing calls on the first three tables, and statistics settings on the fourth page.
Bizfon Manual II: Administrator's Guide Administrator's Menus criteria. Wildcard symbols are allowed here. The Call Statistics - Successful Calls, Call Statistics Missed Calls and Call Statistics - NonSuccessful Calls tables are lists of successful, missed and unsuccessful incoming and outgoing calls and their parameters (Call Start Time, Call Duration, Call destinations). Each column heading in the tables is a link. By clicking on the column heading, the table will be sorted by the selected column.
Bizfon Manual II: Administrator's Guide Administrator's Menus If Si is the RTP timestamp from packet i, and Ri is the time of arrival in RTP timestamp units for packet i, then variance for packet i may be expressed as following: V(i) = |(Ri - R1) - (Si - S1)| = |(Ri - Si) - (R1 - S1)| Rx Maximum Delay = max V(i) / 8 Please Note: RTP Statistics is logged only when at least one of the call endpoints is located on the Bizfon, e.g.
Bizfon Manual II: Administrator's Guide Administrator's Menus RTP Settings The RTP Settings page allows the administrator to configure the codec’s packet size and silence suppression for each voice codec, to select the G726 codec standard, to define RTP/RTCP port ranges, etc. All parameters listed on this page may be modified and submitted. The Codec Properties table lists all codecs with the corresponding packetization interval and information about silence suppression.
Bizfon Manual II: Administrator's Guide Administrator's Menus NAT Traversal Settings The NAT Traversal Settings page is divided into separate pages used to configure General NAT settings, SIP NAT parameters, RTP and STUN parameters for NAT and a page where the NAT Exclusion table may be filled.
Bizfon Manual II: Administrator's Guide • Administrator's Menus Max - maximal port has to be lower than 65536 and higher than the minimal port range. Only odd numbers are allowed. Please Note: RTP/RTCP Mapped Port ranges should be greater than or equal to the RTP/RTCP port ranges defined on the RTP Settings page. The STUN Parameters page enables automatic NAT configuration through the STUN server and is used to configure the STUN (Simple Traversal of UDP over NAT) client on the Bizfon.
Bizfon Manual II: Administrator's Guide Administrator's Menus IP address requires the IP address that is placed behind NAT within the local network. Subnet Mask requires the subnet mask corresponding to the specified IP address. Fig. II-89: NAT Exclusion Table - Add Entry page To Configure the NAT Exclusion Table 1. 2. 3. Press the Add button on the NAT Exclusion Table page. The Add Entry page will appear in the browser window. Specify an IP Address and its Subnet Mask in the corresponding text fields.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Bizfon sends the current time/date to the called phone together with the caller’s information. A group of Remote Party Disconnect Indication parameters are used especially to configure the private PBX attached to the Bizfon FXS port. • The Enable Busy Tone Indication checkbox enables the busy tone transmission to the FXS port when the remote party being in call is disconnected.
Bizfon Manual II: Administrator's Guide Administrator's Menus The IP Lines table lists all available IP lines with additional information about each of them: number of the extension attached to it, information about the phone type and the configuration details. Each column heading in the tables is link. By clicking on the column heading, the table will be sorted by the selected column. Upon sorting (ascending or descending), arrows will be displayed close to the column heading.
Bizfon Manual II: Administrator's Guide Administrator's Menus The FXS Lines Loopback table lists all the FXS lines on the Bizfon along with their loopback parameters (Loopback State and Loopback Timeout). The Edit functional link leads to the FXS Lines Loopback Settings Edit Entry page where Loopback Timeout (in seconds) may be configured for one or more selected FXS line(s). The Enable/Disable Loopback functional link is used to enable/disable the Loopback service on the selected FXS line(s). Fig.
Bizfon Manual II: Administrator's Guide Administrator's Menus Gain Control The Gain Control settings are used to define the transmit and receive gains. For FXS lines, Transmit Gain defines the phone speaker volume and Receive Gain defines the phone microphone volume. For FXO linesTransmit Gain defines the level of voice transmitted from Bizfon to the PSTN network and Receive Gain defines the volume of voice received by Bizfon from the PSTN network.
Bizfon Manual II: Administrator's Guide Administrator's Menus Fig. II-98: Call Routing table Defining patterns in the Call Routing Table avoids registering Bizfon at the routing management server and gives a possibility to establish a direct connection to the destination or to use a SIP server for call routing.
Bizfon Manual II: Administrator's Guide Administrator's Menus Number of Discarded Symbols (NDS) requires the number of symbols that should be discarded from the beginning of the routing pattern. The field should be empty if no digits need to be discarded. Only numeric values are allowed for this field, otherwise an error message occurs: “Error: Number of Discarded Symbols is incorrect - digits allowed only”.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Multiple Logons (ML) checkbox is available only for the IP-PSTN call type and allows/denies multiple logon to the public SIP server with the same username at the same time. Use RTP Proxy checkbox is available for SIP and IP-PSTN call types and is applicable only when route is used for calls through Bizfon between peers both located outside the Bizfon.
Bizfon Manual II: Administrator's Guide The Call Routing Wizard - Page 3 appears if the Fill Call Source Information checkbox previously had been enabled on Page 1 of the Call Routing Wizard, and it will require information about the Inbound caller. The Inbound Caller Pattern field requires the caller’s address where the current route will be applied. Alphanumerics and any characters supported in the SIP username are allowed for this field.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Move Up/Move Down buttons are used to move call routing patterns one level up or down within the Call Routing table. The consecution of the routing patterns is important when making routing calls as the Call Routing table is parsed from the top down and routing will take place according to the first pattern that matches the dialed number.
Bizfon Manual II: Administrator's Guide Administrator's Menus 16. If Filter on Caller / Call Type / Modify Caller ID checkbox has been previously enabled and the call type is different from the FXO, fill Inbound Caller Pattern in the corresponding text field, choose the needed value from Inbound Call Type drop down list, as well as Inbound Number of Discarded Symbols and Inbound Prefix values. 17. Press the Next button. 18.
Bizfon Manual II: Administrator's Guide Administrator's Menus The step by step discussion of the Best Matching Algorithm is as follows. Step 1: The list is split into two groups separating the patterns with “*” from the ones without (Criterion 1). The patterns with “*” form a group with lower priority and are pushed back to the end of the list (Table 1).
Bizfon Manual II: Administrator's Guide Administrator's Menus Table 4 Table 5 The list of patterns 1231 123? 1[1-3]3[0-8] ?2?1 {100-150, asd, \*\?}1 [1-3]??? 12*31 Criterion 3 2 0 - 123* *2*1 - *1* {11-15}3* 0 0 [1-3]* * 1 0 The list of patterns 1231 123? 1[1-3]3[0-8] ?2?1 Criterion 3 2 0 {100-150, asd, \*\?}1 [1-3]??? 12*31 - 123* *2*1 - *1* {11-15}3* 0 0 [1-3]* * 1 0 Step 4: Each sub list is sorted separately from the others by the number of question marks in the pattern in descending
Bizfon Manual II: Administrator's Guide Administrator's Menus Step 6: This step is applicable to the subgroup containing patterns with “*”, the group with lower priority. Each sub-list is sorted separately from the others by the number of asterisks (“*”) in ascending order (Criterion 6). The patterns that have the same number of asterisks are grouped into sub-lists. If a sub-list consists of one pattern it stays in its position and does not participate in further discussions.
Bizfon Manual II: Administrator's Guide Administrator's Menus VoIP Carrier Wizard – Page 2 is used to define VoIP Carrier Settings. Page contains following components: 1. VoIP Carrier Common Settings Account Name text field requires a username for authentication on the defined SIP server. Password requires a password for authentication on the defined SIP server. Confirm Password requires a password confirmation.
Bizfon Manual II: Administrator's Guide Administrator's Menus RADIUS Client Settings The RADIUS (Remote Authentication Dial In User Service) specifies the RADIUS protocol used for authentication, authorization and accounting, to differentiate, to secure and to account for the users. The RADIUS Server gives an extra possibility for caller from/through Bizfon to pass authentication to be able to dial the specific number.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Username field is dedicated for accounting service only and is used to insert an identification username accounting will be performed on behalf of. When no username is specified in this field, source username will be used for accounting. Send Accounting messages manipulation radio buttons group is used to select the whether both Start and Stop Accounting messages should be sent or Stop Accounting message is delivered only.
Bizfon Manual II: Administrator's Guide Administrator's Menus Internet Uplink Menu Fig. II-109: Internet Uplink menu in Dynamo theme Fig. II-110: Internet Uplink menu in Plain theme PPP/ PPTP Settings The PPP/PPTP Settings page is used to establish a connection over the DSL link or any other type of uplink, to the ISP (provider party). A connection is needed to set up and to make or receive calls through PPP over Ethernet. The connection may be configured for manual setup or to be always up.
Bizfon Manual II: Administrator's Guide Administrator's Menus Enable automatic PPP restart at checkbox is used to select the time when PPP connection will be automatically restarted. Checkbox selection enables LCP echo failures text field that indicates the number of LCP echo failure packets received before the PPP connection will be considered as dead and will be restarted.
Bizfon Manual II: Administrator's Guide Administrator's Menus When Bizfon is connected to the Internet with a fixed IP address, it will be set up to act as a VPN gateway. Then Bizfon is prepared to establish an IPSec connection with another VPN gateway device, but allows access to Road Warriors, too. A traveling salesperson's notebook for example could be such a Road Warrior. Access to their company’s intranet via IPSec connection can be obtained regardless of location.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Peer type drop down list is used to choose the remote machine type for the IPSec Connection to be established. If the list does not include the required type of machine, choose Other. VPN Network Topology drop down list allows to select the location of the peers participating to the VPN connection. Following selections are present in the list: • Bizfon<>Peer – direct connection between Bizfon and a peer.
Bizfon Manual II: Administrator's Guide Administrator's Menus Auto Keying requires the ESP (Encapsulated Security payload) and IKE (Internet Key Exchange) settings (in addition with Diffie-Helman Group settings) to be selected for the automatic keying exchange. Encryption and Authentication parameters should be defined for each of these standards, as well as for the Manual Keying.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Manual Keying page offers the following components: Depending on the selected encryption and authentication services of the prior page (IPSec Connection Properties) you will get some of the following text fields: • • • • DES Encryption Key 3DES Encryption Key SHA1 Authentication Key MD5 Authentication Key Manual keys must be entered in the hexadecimal format, otherwise the “Incorrect Encryption Key” error appears.
Bizfon Manual II: Administrator's Guide Administrator's Menus The PPTP Client Configuration link displays a page where all existing PPTP client connections are listed, characterized by their Connection Name, the State of the PPTP connection (Pending, Disabled, Trying…, Authentication Failure, No Connectivity - still trying, Unknown, Broken, or Connected) and the Remote IP/Hostname (the IP address or the hostname of the PPTP server).
Bizfon Manual II: Administrator's Guide Administrator's Menus Please Note: All settings should be configured the same way on both the PPTP client and server, that is to say, for successful PPTP tunnel establishment, all settings should match. The PPTP Server Configuration page is used to configure the PPTP server settings and offers the following components: The PPTP Subnet text fields are used to enter the IP address range for the PPTP server and clients within the PPTP tunnel.
Bizfon Manual II: Administrator's Guide Administrator's Menus The Active L2TP Connection - Add Entry page is used to specify L2TP client connections and offers the following components: The Server Host Name text field requires the L2TP server’s name. Please Note: The input in the Server Host Name field should be only in Latin characters, otherwise an error occurs and no L2TP connection can be created. The Client Host Password text field requires the local peer password.
Bizfon Manual II: Administrator's Guide Administrator's Menus To Add a Passive L2TP Connection 1. 2. 3. 4. Press the Add button on the L2TP Configuration page. Select the Passive Connection link. Enter the client host name and the password in the Client Host Name and Client Password text fields. Press Save to add a passive L2TP connection with these settings. To Delete/Stop/Start/Enable/Disable a VPN Connection 1. 2. 3.
Bizfon Manual II: Administrator's Guide Administrator's Menus The request modifies the nameserver database so that the hostname will be resolved to the new IP address. The Basic Authentication checkbox enables the encoding of the username and password entered in the text fields above, and then uses the Basic Authentication method to notify the provider about the user authentication settings. Most of the DynDNS providers require an authentication for security.
Bizfon Manual II: Administrator's Guide Administrator's Menus Please Note: Applying firewall rules will just prevent the establishment of new connections that violate the rules. Applying rules does not kill existing connections that violate the rule.
Bizfon Manual II: Administrator's Guide Administrator's Menus For example, the page to add a rule for Incoming Traffic/Port Forwarding offers the following input options: Service includes a list of possible services to be configured. All user defined services also will be displayed in this list. Action includes possible actions to setup the rule. Forward to IP requires the destination IP address where traffic should be transferred to, if it comes from the restricted host.
Bizfon Manual II: Administrator's Guide Administrator's Menus Service Pool The Service Pool table is a list of all created services and their parameters. It is used to add new services with the appropriate settings (protocol type and port range). New services can be used to add a restriction or permission by defining a new filtering rule: Add opens the Add New Service page where new services may be added.
Bizfon Manual II: Administrator's Guide Administrator's Menus comment in the member column. Add opens the Add Group page where a new group may be added. This page consists of the Group Name text field (requiring the group name) and the Group Description text field (requiring the optional group description), as well as standard Save and Back buttons to apply or abort changes. Edit opens the Edit Group page where the service parameters can be modified. It provides the same components as the Add Group page.
Bizfon Manual II: Administrator's Guide Administrator's Menus To Delete a Group 1. 2. 3. 4. Select the Manage IP Pool Groups link. The IP Pool Configuration page appears with the table of groups (if any). Check the one or more checkboxes of the corresponding groups that ought to be deleted from the groups table. Press Select all if all groups ought to be deleted. Press the Delete button on the IP Pool Configuration page. Confirm the deletion with Yes or quit with No. Bizfon2000 (SW Version 3.1.
Bizfon Manual II: Administrator's Guide Administrator's Menus LAN Services Menu Fig. II-141: LAN Services menu in Plain theme Fig. II-140: LAN Services menu in Dynamo theme DNS Settings The DNS Settings page gives the possibility to setup a name server for the Bizfon. It offers the following components: NameserverAssignment radio buttons: • Dynamically by provider selection automatically configures the assignment of the name server address from the provider party.
Bizfon Manual II: Administrator's Guide Administrator's Menus IP address - host IP address, assigned by Bizfon. MAC address - host MAC address, provided by the host itself. Lease Start - date and time when the leased IP address has been activated. Lease End - date and time when the leased IP address has been or will be deactivated. Hostname - hostname, provided by the host itself. Bizfon2000 (SW Version 3.1.x) Fig.
Bizfon Manual II: Administrator's Guide Administrator's Menus Administrator’s Additional Features Incoming Call Blocking and Outgoing Call Blocking The Incoming Call Blocking and Outgoing Call Blocking pages offer extended features for the administrator to activate incoming/outgoing call blocking services for certain callers. This configuration cannot be changed by the users.
Bizfon Manual II: Administrator's Guide Welcome Page Appendix: Extension User's Welcome Page This welcome page may be helpful, if administrators want to inform their extension users about individual data, they need to use the extensions. Such as phone numbers, phone lines, IP addresses and SIP numbers. To get a word form that may be edited and sent by mail, double-click on the paperclip sidewise. Welcome You are using a Bizfon Voice Router made by Bizfon Inc.
Bizfon Manual II: Administrator's Guide System Default Values Appendix: System Default Values Administrator Settings Parameter System Default Value Admin Settings Login name -admin Password - 19 Bizfon Hostname bizfon LAN IP Address 172.30.0.1 Subnet Mask - 255.255.0.0 DHCP Server Enabled, IP Range - 172.30.0.100-172.30.0.254, WINS - 0.0.0.0. Regional Settings and Preferences Locale – US, TimerZone - US/Central, Theme – Dynamo. Emergency and PSTN codes Emergency code -911, PSTN code – 9.
Bizfon Manual II: Administrator's Guide System Default Values Parameter System Default Value Extension Settings – SIP Advanced User ID – undefined, Send Keep-alive Messages to Proxy – disabled, RTP Priority Level – medium, Outbound Proxy, Secondary SIP Server and Outbound Proxy for Secondary SIP Server – undefined.
Bizfon Manual II: Administrator's Guide Parameter System Default Values System Default Value Secondary STUN Server – undefined Secondary STUN Port - undefined Polling Interval: 1 hour Keep-alive interval: 120 seconds NAT IP checking interval: 300 seconds No entries in NAT Exclusion table Line Settings Onboard Lines Configuration: CallerID- Standard 2 FSK for all lines Ringer type: Type A for all lines Busy Tone and Power Disconnect indications: disabled for all lines Off-hook caller ID - disabled for all
Administrator's Manual Appendix: System Default Values Extension Settings Parameter Voice Mail Settings System Default Value Maximal mail message duration - 5 min, Send end of greeting message – disabled, Ask password before granting local access to mail box – disabled, Ask password before granting remote access to mail box – enabled, Send welcome message – disabled, Play Voice Mail help – enabled, Automatically play messages - enabled, Send mails count information message – disabled, Send date/time inf
Bizfon Manual II: Administrator's Guide About this Administrator's Guide Appendix: Software License Agreement BIZFON Inc. Software License Agreement THIS IS A CONTRACT. CAREFULLY READ ALL THE TERMS AND CONDITIONS CONTAINED IN THIS AGREEMENT. USE OF THE BIZFON HARDWARE AND OPERATIONAL SOFTWARE PROGRAM INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF YOU DO NOT AGREE TO THESE TERMS AND CONDITIONS, YOU MAY NOT USE THE HARDWARE OR SOFTWARE. 1. License. Bizfon, Inc.
Bizfon Manual II: Administrator's Guide About this Administrator's Guide calls. 10. U.S. Government Restricted Rights. The Licensed Materials are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraphs (c)(1) and (2) of the Commercial Computer Software—Restricted Rights clause at 48 C.F.R. section 52.227-19, or subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227.
