User's Manual SRP-350IIOBE Thermal Printer Rev. 1.00 http://www.bixolon.
SRP-350IIOBE ■ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. You must use only the supplied adapter. • • • • • It is dangerous to use other adapters. This can provoke over-heating and a fire. If the plug is wet or dirty, dry or wipe it before usage.
SRP-350IIOBE CAUTION Violating following instructions can cause slight wound or damage the appliance. If you observe a strange smoke, odor or noise from the printer, unplug it before taking following measures. Keep the desiccant out of children’s reach. • If not, they may eat it. • Switch off the printer and unplug the set from the mains. • After the disappearance of the smoke, call your dealer to repair it. TO UNPLUG PROHIBITED PRINTER Install the printer on the stable surface.
SRP-350IIOBE ■ Warning - U.S.A 1) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
SRP-350IIOBE ■ Waste Electrical and Electric Equipment (WEEE) This marking shown on the product or its literature, indicates that is should not be disposed with other household wastes at the end of its working life, To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
SRP-350IIOBE ■ Introduction The SRP-350IIOBE Roll Printer are designed for use with electronic instruments such as system ECR, POS, banking equipment, computer peripheral equipment, etc. The main features of the printer are as follows: 1. High speed printing : 47.28 (1/6” Feed) lines per second. 2. Low noise thermal printing. 3. USB / Ethernet / Bluetooth On-board Type 4. The data buffer allows the unit to receive print data even during printing. 5.
SRP-350IIOBE ■ Table of Contents 1. Setting Up the Printer .................................................................................................... 8 1-1 Unpacking................................................................................................................... 8 1-2 Connecting the Cables ............................................................................................... 9 1-2-1 Ethernet Interface ......................................................................
SRP-350IIOBE 1. Setting Up the Printer 1-1 Unpacking Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. SRP-350IIOBE Roll Paper Rev. 1.
SRP-350IIOBE 1-2 Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector panel on the back of the printer, which is shown below: ※ NOTE Before connecting any of the cables, make sure that both the printer and the host are turned off.
SRP-350IIOBE 3) Ethernet Interface signal descriptions Pin No. 1 2 3 4 5 6 7 8 Signal name TD+ TDTCT NC NC RCT RD+ RD- Assignment(Color) White Orange Orange White Green Blue White Blue Green White Brown Brown Function Transmit + Transmit Receive + Receive - * For more information, refer to the Ethernet User Manual in Bixolon Web Site. 1-2-2 USB Interface Drawer kick-out connector USB connector Pin No.
SRP-350IIOBE 1-3 Connecting the Drawer ※ WARNING Use a drawer that matches the printer specification. Using an improper drawer may damage the drawer as well as the printer. ※ CAUTION Do not connect a telephone line to the drawer kick-out connector; otherwise the printer and the telephone line may be damaged. Plug the drawer cable into the drawer kick-out connector on the back of the printer next to the power supply connector. Pin No.
SRP-350IIOBE 1-5 Installing or Replacing the Paper Roll ※ NOTE Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1-5-1 Make sure that the printer is not receiving data; otherwise, data may be lost. 1-5-2 Open the paper roll cover by pressing the cover-open button. ※ NOTE Do not open the print cover while the printer is operating. This may damage the printer.
SRP-350IIOBE 1-5-5 Be sure to note the correct direction that the paper comes off the roll. 1-5-6 Pull out a small amount of paper, as shown. Then close the cover. ※ NOTE When closing the cover, press the center of printer cover firmly to prevent paper miss-loading. 1-5-7 Tear off the paper as shown. Rev. 1.
SRP-350IIOBE 1-6 Adjustments and Settings The SRP-350IIOBE is set up at the factory to be appropriate for almost all users. It does, however, offer some settings for users with special requirements. It has DIP switches that allow you to change communication settings, such as handshaking and parity check, as well as print density. The SRP-350IIOBE also has a near-end sensor for the paper. This can give you a warning when the paper is almost out.
SRP-350IIOBE 1-8 Connecting the Power Supply ※ CAUTIONS When connecting or disconnecting the power supply from the printer, make sure that the power supply is not plugged into an electrical outlet. Otherwise you may damage the power supply or the printer. If the power supply’s rated voltage and your outlet’s voltage do not match, contact your dealer for assistance. Do not plug in the power cord. Otherwise, you may damage the power supply or the printer.
SRP-350IIOBE 2. Self Test The self-test checks whether the printer has any problems. If the printer does not function properly, contact your dealer. The self-test checks the following; 2-1 Make sure paper roll has been installed properly. 2-2 Turn on the power while holding down the FEED button until it beep 3times. The self-test begins. 2-3 The self-test prints the current printer status, which provides the control ROM version and the DIP switch setting.
SRP-350IIOBE 3. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in finding software problems. When you turn on the hexadecimal dump function, the printer prints all commands and data in hexadecimal format along with a guide section to help you find specific commands. To use the hexadecimal dump function, follow these steps. 3-1 After you make sure that the printer is off, open the cover.
SRP-350IIOBE 4. Specification Printing method Dot density Printing width Paper width Thermal line printing 180 dpi (7dots/mm) 72 mm 80 mm 42 (Font A) Characters per line (default) 56 (Font B) 56 (Font C) Printing speed 47.28lines/sec , 200 mm/sec Receive Buffer Size 4K Bytes ※ NOTE : Printing speed may be slower, depending on the data transmission speed and the combination of control commands.
SRP-350IIOBE 5. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality. In this case clean the printer as follows. 5-1-1 Open the printer cover and remove the paper if exists. 5-1-2 Clean the print head with a cotton swab moistened with alcohol solvent. 5-1-3 Clean the platen roller and paper end sensor with cotton swab moistened with water. 5-1-4 Insert a paper roll and close the printer cover.
