Bittium Tough Mobile 2 Quick Start Guide
Device at a glance 1 Headset and protective cover 2 Emergency key 3 Earpiece and microphone 4 Front camera 5 Status indicator LED 6 Back camera 7 Flash LED 8 Volume up key 9 Push to Talk key (PTT) 10 Volume down key 11 USB 3.1 port (USB-C) 12 Privacy Mode key 12 13 Power key 14 SIM tray 15 Loudspeakers The ambient light sensor and proximity sensor are located next to the status LED.
1 2 3 4 5 6 7 8 9 10 15 14 13 12 11 Please read this quick guide carefully before using the device. Bittium Tough Mobile 2 is factory tested to be IP67 resistant to dust and water. Intentional underwater immersion of the device should be avoided. The device is not designed for underwater use or use in a shower. Purposeful use of the device in these environments will invalidate the warranty. For more info on Bittium Tough Mobile 2 Ingress Protection see http:// www.bittium.
Box contents Device sales package contains the following items: • • • • • Charger USB C cable 3.5 mm Headset SIM tray tool Quick Start Guide Box contents and the appearance of the accessories may vary. Operating system and applications Bittium Tough Mobile 2 uses the Android operating system. This Quick Start Guide contains only highlights and device-specific features and functionalities. For a full Android User Guide please refer to: http://www. bittium.com/BittiumToughMobile2#support.
Getting started To start using the device first open the SIM card tray and insert the SIM card(s). To open the SIM tray insert the SIM tray tool into the hole shown below. Push the tool gently into the hole until the SIM tray pops out. Insert the SIM card and optional SDHC card as shown below.
Insert your primary Nano SIM card onto the SIM card slot as shown above. If you have a secondary Nano SIM card, insert it onto the Dual Mode slot. In case you are not using two SIM cards you can insert your Micro SDHC card onto the Dual Mode slot. After the SIM and SD cards are inserted, push the SIM tray back. See the figure below if you are inserting two SIM cards. NOTE: In order to maintain water and dust resistance, keep the rubber seal around the SIM tray clean of any dirt.
Once the device has powered up, follow the on-screen instructions to set up the device using the Security Wizard.
Security wizard The device is equipped with a Security Wizard that is launched during the initial power up of the device. Security Wizard is used to set up a number of different device settings. Follow the on-screen instructions by first setting a screen lock code. The number of set up steps may vary depending on the security features of the device. Lock screen Switching off the display locks the device. The device also locks after a period of inactivity.
Special key functions The device has dedicated special keys in addition to the Push to Talk (PTT) function. The emergency key is a configurable button. The Privacy Mode key switches the device to ‘Do not disturb’ mode. See Privacy Mode section for more information.
• Sensor accuracy is reduced Activate/deactivate the privacy mode by pressing the Privacy Mode key for 3 seconds. Software update Use software update to manually check for available software updates and install them on your device. 1. Go to Settings -> System -> Advanced -> Additional system updates. 2. Tap ‘Check Now’ to check if an update is available. You can also set the schedule for OTA (over-the-air) updates by tapping Check OTA updates. Options are: Disabled, Daily, Weekly and Monthly.
Important health and safety precautions Please take the following safety precautions when using the device: WARNINGS Only use the batteries, antennas and chargers approved by Bittium Wireless Ltd. The use of non-Bittium approved batteries, antennas, and chargers may be dangerous. Permanent hearing loss may occur if earphones or headphones are used at high volume for prolonged periods of time. Do not use the charger if it has a visible defect, or if you suspect it is damaged.
CAUTIONS The material used in the display is glass. The display can break if your handset is dropped or if it receives a significant impact. Do not use the device if the screen is broken or cracked as this may cause an injury. Any modification to this product is prohibited and will invalidate the warranty.
Important customer information Bittium Tough Mobile 2 is a wireless device, containing a radio transmitter and receiver which emit radio frequency energy during its use. Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the radio signals from a wireless phone. Do not use the device near medical equipment without permission.
Turn Bittium Tough Mobile 2 OFF in any facility where posted notices so require. To avoid interfering with blasting operations turn Bittium Tough Mobile 2 OFF when in a blasting area or in areas posted: “Turn off two-way radio”. Obey all signs and instructions. Turn Bittium Tough Mobile 2 OFF when in areas with a potentially explosive atmosphere and obey all signs and instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.
FCC notice to users This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
To satisfy the FCC RF Exposure requirements for mobile transmitting devices, a separation distance of 10 mm should be maintained between the antennas of this device and persons during operation. To ensure compliance, operations at closer distances than this are not recommended.
Frequency bands and power Following table lists the frequency bands in which the radio equipment operates as well as the maximum radio-frequency power transmitted in these frequency bands: Frequency bands and maximum transmitted radio frequency power GSM850/900: 33.3dBm, GSM1800/1900: 30.8dBm, WCDMA Bands 1,2,4,5,8: 25dBm, LTE Bands FDD: 1,2,3,4,5,7,8,12,13,14,17, 20,25,26,28,29,30,66: 25.5dBm, LTE Bands TDD: 34,38,39 25dBm Wi-Fi 2.4G: 16.5dBm, Wi-Fi 5G: 17dBm, Bluetooth: 12.
Limited warranty For a period of 1 year from the date of purchase, Bittium Wireless Ltd. (“Bittium”) warrants this Product, including all accessories provided in the sales box, against defects in materials or workmanship. If this Product is determined to be defective within the 1 year warranty period, Bittium will repair the Product or replace it with a new or refurbished Product, at its option, at no charge to the customer, except as set forth below.
Notes Bittium Tough Mobile 2 Quick Start Guide 19
Published by: Bittium Wireless Ltd. Ritaharjuntie 1 90590 Oulu Finland Phone: +358 40 344 2000 www.bittium.com For the latest Quick Start Guide see: www.bittium.com/BittiumToughMobile2 #support Guide is also available in your device: Settings-> About phone->User guide->Quick user guide. Legal Notice Copyright 2019 Bittium. All rights reserved. The information contained herein is subject to change without notice. Bittium retains ownership of and all other rights to the material expressed in this document.
