USER'S GUIDE 53U6, 34T2 SERIES 220-240V 2 Thank You 3 Safety Instructions 4-5 6 7-14 15 16-17 Product View Assembly Operations Maintenance and Care Troubleshooting 18 Replacement Parts 18 Accessories and Formulas 19 Warranty 20 Consumer Services
Thanks for buying a BISSELL CleanView® ProHeat® We’re glad you purchased a BISSELL CleanView® ProHeat®. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL CleanView® ProHeat® is well made, and we back it with a limited two year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: ■ Remove plug from electrical outlet before Read all instructions before using your deep cleaner.
Product view Ergonomically Designed Handle Handle Assembly Heat Indicator Light/Built-in Hot Water Heater Heater Switch: Turn heat on or off as needed Lower Body Assembly Integrated Carry Handle ReadyTools™ Dial Belt Access Door Removable Nozzle Edge Sweep™ Brushes 4 www.bissell.
Product view Spray Trigger Cord Clip Quick Release™ Cord Wrap Tough Stain Tool Hose Secure Latch Power Cord Ready-to-Use Hose WARNING: To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning formulas intended for use with the deep cleaner. NonBISSELL cleaning formulas may harm the machine and void the warranty.
Assembly Your CleanView® ProHeat® comes in four easy to assemble components: • Handle assembly • Upper hose rack • Lower body assembly • Lower hose rack Four Phillips head screws are included, 2 long and 2 short. They can be found taped to the handle assembly. Warning: Do not plug in your cleaner until you have completely assembled it per the instructions and are familiar with all instructions and operating procedures. The only tool you will need to assemble your cleaner is a Phillips head screwdriver.
Operations Special features Your BISSELL CleanView® ProHeat® is a home cleaning system that uses a combination of heat, BISSELL cleaning formula, brush agitation and suction to safely clean carpets. Heater Switch Built-In-Heater BISSELL CleanView® ProHeat® models all feature a patented built-in heater which will heat the hand hot tap water you put in it to safely optimise cleaning effectiveness. The heater will never allow the temperature to exceed 82°C degrees.
Operations Special features continued Scotchgard™ Protector Carpet protection applied at the mill typically wears down over time from heavy foot traffic and everyday cleaning, including deep cleaning. To help restore this important protection, only BISSELL offers cleaning formulas with Scotchgard protector. This offers extra protection against dirt and tough stains to keep your carpets looking good longer.
Operations Before you clean 1. Plan activities to give your carpet time to dry. 2. Move furniture to another area if cleaning an entire room (optional). 3. Vacuum area with a dry vacuum cleaner before deep cleaning. 4. Plan your cleaning route to leave an exit path. It is best to begin cleaning in the corner farthest from your exit. EXIT 12 5 9 10 11 6 7 2 4 3 1 T STAR E HER 3' 4' 5.
Operations Fill the 2-in-1 water tank 1. 2. 3. 4. 5. 6. 1. Remove the tank from the base of the machine by lifting the tank carry handle. 2. Carry like a bucket to the sink. Rotate the handle forward to unlatch the lid. Remove lid, turn over and locate built in measuring cup. 3. Fill with BISSELL 2X formula to the indicated fill line on the built in measuring cup and pour into mouth of the bladder. 4. Fill the bladder with clean hand hot tap water.
Operations Carpet cleaning 1. Plug the deep cleaner into a proper outlet. Set ReadyTools dial to the Floor Cleaning setting. Turn the power on by pressing the red power switch on the back of the unit with your foot. Turn heater switch (located on side of unit) to the on position. Allow one minute for the built-in heater to warm up before cleaning. NOTE: The CleanView® ProHeat® will be fully warmed and will provide optimal performance after one minute of continuous heated cleaning. 2.
Operations Empty the 2-in-1 water tank/clean removable nozzle 1. Turn power switch off. Remove the 2-in-1 water tank from the base using the tank carry handle. Carry the tank like a bucket to a utility sink or outside where you will dispose of the collection water. Remove the top of the tank by rotating the handle forward to unlatch lid and lifting lid off tank. 2. 1. 2. Empty collection water from bottom of tank. 3. After each use, remove and rinse the lint screen located on the tank lid. 4.
Operations ReadyTools™ continued 5. Vacuum thoroughly to pick up loose debris and pet hair. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts. 6. To begin cleaning with attachments, follow the instructions on page 10 for filling the 2-in-1 water tank. 7. 7. Set the ReadyTools dial to the TOOLS setting. This will allow spray and suction from the hose. 8. Attach the cleaning tool of your choice to the end of the hose. 9.
Operations ReadyTools™ continued Cleaning with Deep Reach™ Tool (select models only) 1. 1. Set tool on soiled surfaces and press the spray trigger to spray solution onto the soiled area to be cleaned. 2. Slowly move the tool back and forth over the soiled surface, keeping the tool in contact with the carpet. Release spray trigger and move tool slowly over the soiled area to suction up water and dirt. 4. Continue to clean the area, working in small sections, until no more dirt can be removed.
Maintenance and care Hard Floor Cleaning continued 8. While pressing the spray trigger, make one slow forward wet pass and another back.Caution: Do Not Overwet. 9. Repeat the motion without pressing the spray trigger using the hard floor tool to squeegee and suction up the dirty water. 10. When finished, remove hard floor tool, rinse and let dry before storing. Refer to the Maintenance and care section on page 15 for machine clean up and storage instructions.
Troubleshooting WARNING: To reduce the risk of electric shock, or injury, unplug from the outlet before servcing Heat indicator light does not illuminate Possible Causes Remedies 1. The heater switch is not turned on. 1. Turn on the heater switch located on side of unit. 2. The machine power switch is not turned on. 2. Both switches must be on to activate the heat indicator light. Reduced spray OR no spray Possible cause Remedies 1. Bladder may be empty. 1.
Troubleshooting DirtLifter PowerBrush does not turn Possible cause 1. Remedies The brush belt or pump belt is off or broken. 1. Refer to Remedy 4 on page 16 to check if brush belt or pump belt is broken. Cleaner not picking up solution Possible cause Remedies 1. ReadyTools dial may be on the wrong setting for the cleaning job. 1. Set ReadyTools dial to either FLOOR CLEANING or TOOLS. 2. Poor tool position. (Hand held attachments only). 2. Adjust angle; apply more downward pressure. 3.
Replacement parts Item 1 Part No. 1 2 3 4 5 6 2 203-0104 203-0102 203-8114 215-0628 015-0621 203-0105 Part Name 3 Tank Assembly Complete Tank Base Removable Nozzle Replacement Pump Belt (with instructions) Replacement Brush Belt (with instructions) Lint Screen 4 5 6 Accessories and formulas While not all of these parts may not have come with your machine, all are available to you for purchase, if desired. Item Part No.
Warranty - BISSELL CleanView ® ProHeat® This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or contact your local in country distributor.
BISSELL consumer services If your BISSELL product should require service: Call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. If you have questions about your warranty or need replacement parts please contact the numbers below.