PTCT MINI-32 299-7-05-2
TABLE OF CONTENTS Page SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 MOTOR WIRING AND ELECTRICAL REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . .
— OPERATOR'S NOTES —
NOTICE TO OWNERS AND OPERATORS BIRO’s products are designed to process food products safely and efficiently. Unless the operator is properly trained and supervised, however, there is the possibility of a serious injury. It is the responsibility of the owner to assure that this machine is used properly and safely, strictly following the instructions contained in this Manual and any requirements of local law. No one should use or service this machine without proper training and supervision.
SAFETY TIPS ROTATING GRINDING AUGER & ROTATING MIXING PADDLES TO AVOID SERIOUS PERSONAL INJURY NEVER Touch This Machine without Training and Authorization by Your Supervisor. NEVER Place Hands into Machine Input or Output Openings. NEVER Open Machine During Operation. ONLY Use a Qualified Electrician to Install According to Local Building Codes: Machine MUST Be Properly Grounded. ALWAYS Connect to Proper Voltage & Phase.
INSTALLATION TO AVOID SERIOUS PERSONAL INJURY, PROPERLY INSTALL EQUIPMENT IN ADEQUATE WORK AREA ALWAYS Use Qualified Technician and Electrician for Installation. ALWAYS Connect to Proper Voltage & Phase. ALWAYS Install Equipment in Work Area with Adequate Light and Space Away From Children and Visitors. ONLY Operate on a Solid, Level, Non-Skid Surface. ALWAYS Lock Machine Castors After Moving Machine. NEVER Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition.
MOTOR WIRING AND ELECTRICAL REQUIREMENTS 1. Interchange of motor current is made in motor outlet box. Leads are properly marked. Changing instructions are on the motor plate or inside junction box cover. 2. All grinders are wired 220 volts unless otherwise specified. Be sure motor specifications (voltage, cycle, phase) match power supply line. Be sure line voltage is up to specification. 3. Connect leads to machine in a manner that will be approved by local electrical inspectors. 4.
10. The start stop switch and the grind engage lever are located on the right side of the machine when facing the grinding bowl. The start stop switch will activate the mixer paddles. The start stop switch will also activate the grinding auger only when the grind lever is in the "engaged" position. To deactivate the grinding operation move the grind lever to the "disengaged" position. The tank and hopper cover interlock switches are located in the motor compartment.
PARTS LOCATION 6
OPERATION ROTATING GRINDING AUGER & ROTATING MIXING PADDLE TO AVOID SERIOUS PERSONAL INJURY ONLY Properly Trained Personnel Should Use This Equipment. NEVER Place Hands Into Machine Input or Output Openings. NEVER Open Machine During Operation. DO NOT Wear Gloves While Operating. DO NOT Tamper With, Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition. NEVER Operate Machine With Product Mixer Safety Cover Opened or Hopper Removed or Magnetic Interlock Switch By-Passed.
DO’s DON’Ts • Always keep knife & plate as matched set. • Never, never mix different knives to different • Always keep the knife & plate sharp. • • Always check for straightness by laying the knife on the plate before inserting in machine. • • Always install the knife & plate in correct se- quence, knife 1st, then plate. • Always keep knives & plates lubricated in storage and when starting machine. • Always use coolant when sharpening plates.
DISASSEMBLY INSTRUCTIONS PADDLE REMOVAL: Remove mixing paddle by first locating and lifting up on the hopper lock down clamps releasing them from the hopper. Next loosen the paddle lock knob (black knob located at the front of the hopper). Then turn the locking lever clockwise approximately ¼ turn and remove to unlock the paddle shaft from the hopper. Slide paddle shaft toward front of hopper and lift drive end up and out to remove paddle.
MAINTENANCE ROTATING GRINDING AUGER & ROTATING MIXING PADDLE TO AVOID SERIOUS PERSONAL INJURY ALWAYS Turn Off, Unplug From Power Source and Perform Lockout/Tagout Procedure to This Machine BEFORE Servicing. NEVER Touch This Machine Without Training and Authorization By Your Supervisor. NEVER Place Hands Into Machine Input or Output Openings. NEVER Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition. PROMPTLY REPLACE Any Worn or Illegible Warning Labels.
MOTOR DRIVE COVER AND HOPPER COVER Fig. 9 26 50 51 52 116 116A 117 118 119 120 121 122 123 125 125A 126 127 Item No.
Fig. 1 2 3 4 11 12 12A 12B 13 29 31 33 34 Item No. 15026-02 15029 20050-10 20050-01 53568 53852 53517-1 53594 56302 63036 63041 63043 63045 Description Double roller chain 49" Double chain master link #40 Roller chain #40 Chain master link #40-C/L Paddle locking thumb screw Lock arm assembly w/bushings Thrust bearing Radial bushing Foot switch assembly w/6' tubing Hopper assembly Sprocket D40B35 Sprocket 40B15F-01 Back access panel Fig. 35 36 37 38 39 45 46 54 72 115 124 134 12 Item No.
TRANSMISSION MOUNTING ASSEMBLY Fig. 5 6 8 10 14 15 16 17 18 19 20 21 22 24 25 28 30 32 40 41 42 43 44 Item No. 20665 20665-01 30315 50029 63005 63007 63008 63009 63010 63011 63014 63015 63016 63019 63020 63033 63040 63042 63062 63063 63065 63066 63067 Description Key ¼ ´ ¼ ´ 11 8 SS Key ¼ ´ ¼ ´ 1¾ SS O-Ring 1.25 I.D.
BOWL & WORM ASSEMBLY Fig. 23 60 60A 60B 60C 60D 61 61A 61B 62 63 69 69A 69B 114 Item No.
FASTENERS & LOCATIONS Base Plate (63005) to Cart Assembly (63055) 3 -16 ´ 2¼ 4 ea. HHS088S 8 3 heavy 4 ea. LW25S 8 3 -16 heavy (with loctite) 4 ea. HN25S 8 Frame Side Plates (2 ea. 63009) to Base Plate (63005) 4 ea. HHS058S 5 16-18 ´ 7 8 5 4 ea. LW15S 16 regular 5 8 ea. FW10S 16 Frame Side Plates (2 ea. 63009) to Bearing Retainer-main shaft-rear (1 ea. 63016) 3 -16 ´ 1¼ 4 ea. HHS075S 8 3 heavy 4 ea. LW25S 8 Bowl Support Brackets (LH 63081-01 & RH 63081-02) to Bowl Lock Side Spacer (2 ea.
MINI-32 SCHEMATIC for 208-230/460 Volts, Three Phase, 60 Cycle with Elobau Magnetic Safety Switches 16
OPTIONAL PNEUMATIC FOOTSWITCH 17
SAFETY LABEL LOCATIONS 18
OPERATOR’S SIGNATURE PAGE WARNING READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE SIGNING BELOW MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SERIOUS INJURY TO MYSELF AND OTHERS.
LIMITED WARRANTY: WARRANTY: The Biro Manufacturing Company warrants that the BIRO MINI-32 Grinder will be free from defects in material and workmanship under normal use and with recommended service. BIRO will replace defective parts, which are covered by this limited warranty, provided that the defective parts are authorized for return, shipping charges prepaid, to a designated factory for inspection and/or testing.
