EYES P100 FULL NDI®. NO COMPROMISES.
Contents IMPORTANT INFORMATION.............................................................................................................................................................4 WHAT’S IN THE BOX..........................................................................................................................................................................5 Overview..............................................................................................................................
Operating Instructions Thank you for purchasing our product. If there are any questions, please contact your authorized dealer. Before operating the unit, please read this manual thoroughly and retain it for future reference. Copyright Copyright 2019 BirdDog Australia all rights reserved. No part of this manual may be copied, reproduced, translated, or distributed in any form or by any means without prior consent in writing from our company.
IMPORTANT INFORMATION • Do not aim the camera lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal damage to the camera. Legal Notice Attention: To ensure account security, please change the password after your first login. You are recommended to set a strong password (no less than eight characters). Maintenance Precautions: • If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a rubber dust blowing ball.
WHAT’S IN THE BOX OVERVIEW Note: The camera color may be in white or black per the item that is purchased. This user guide is suitable for the following models: BirdDog Eyes P100 1x BirdDog Eyes P100 Features • Resolution: Up to 1080P60, 1080i59.
Camera Diagrams 1. 12V DC Power Port Connect the supplied DC power adaptor and cord. 9. 2. NDI® Ethernet Port 3. HDMI Port (HDMI 1.4) 10. Communication LED Indicator Flashes orange when the camera receives commands from the infrared remote controller. 4. 3G-SDI Video Output 5. RS-232/422 Control Port (RJ45) RJ45 to RS-232/422 convertor cable is provided. 6. 11. Mic Built-in microphone. Range of sensitivity is within 15 feet. 12. Tripod mounting holes USB Port • For firmware upgrade.
Remote Controller 1. Power • Power ON the camera to turn the camera in operation status. • Power OFF the camera to turn the camera in standby status. • When the camera is powered OFF, the camera turns to the back and would be on standby mode. • When the camera is powered ON, the camera turns to the front. • Powering the camera ON/OFF would not restart the camera. 2. Camera ID (Total 3) Selector 3. Preset Position (Total 6) Calling and Setting 4.
System Configuration Connection Power When the camera is connected to a computer and joystick keyboard with a VISCA cable (cross type, RS-232), you can operate the camera with the computer and the joystick keyboard. • Use only the DC power adaptor (JEITA type4) supplied with the unit. Do not use any other DC power adaptor. • If using POE to power the camera, PoE+(IEEE802.
• System Requirements for your PC 1. 2. 3. 4. Operating System: Microsoft Windows 10/Windows 8/ Windows 7, Linux Ubuntu 16.04LTS, macOS Sierra, Microsoft Windows 7 (32-bit) or above is recommended. When the camera setting HDMI video format at 1080P60/1080P30/720P60, USB2.0 resolution with frame rate are available as following list. •HDMI FORMAT USB 2.0 RES. FRAME RATE • 1920x1080 10P 1280x720 25P / 15P 1024x768 30P / 15P 1080p60/1080p30/720p60 CPU: 2.0 GHz or higher, dual-core.
Camera Control Methods and System Configurations Camera Initial setting status Information Information of the camera initial setting status will display for 5 seconds. 1. Camera PELCO ID for RS-485 control 2. Camera ID for IR Remote Controller 3. IR remote control signal receive current setting This unit has multiple ways of controlling the camera and various system configuration capabilities using optional products.
10. Use RS422(VISCA) / RS485 (PELCO P/D) RS232 Connection 1. Set RS232 control method on Bottom Dip Switch. 2. Set Baud Rate on Bottom Dip Switch to the same as Baud Rate setting on the keyboard you are using. 3. Set specific camera address that you want to control the camera for on Bottom Dip Switch. 4. If you want to have the camera address to be automatically assigned by VISCA controller, set camera Dip Switch address to 0. 5.
9. How to make RS422 connection and RS422 Daisy Chain multiple cameras connection with SONY controller as below: 12. Or you can use CAT5/6 T-568B Standard Ethernet cable direct connect between the camera and the controller to make RS422 connection by following the pin definition below: SONY Keyboard RS422 Connection SONY Keyboard Connection Keyboard 1. --2. --3. --4. --5. GND 6. RXD IN – 7. RXD IN + 8. TXD IN – 9.
PELCO P/D Keyboard RS485 Connection • NOTE: Use RS422 ports for RS485 connection. Only use TX+ and TX- for RS485 connection. • Set RS422 control method on Bottom Dip Switch. • Set Baud Rate on Bottom Dip Switch to the same as Baud Rate setting on the keyboard you are using. • Set the camera ID on OSD menu by remote controller • Reboot the camera by turning it Off/On after the Bottom Dip Switch has been set up correctly. • Use PELCO P/D compatible keyboard.
• between the camera and the joystick controller. VISCA over IP Network Configuration You cannot use the RS-232 connections while you are using the RS422/485 connection. Re-assign the camera The default information of the IP camera is following: Operating Multiple Cameras Using RS-232,422/485 • Static IP: 192.168.0.13 • Subnet mask: 255.255.255.0 • Using RS-232 (VISCA), you can connect to 7 cameras. • Gateway: 192.168.0.1 • Using RS-422 (VISCA), you can connect to 7 cameras.
From the above list, No.1 Camera ID address and NO.2 Video resolution settings can be set in camera OSD menu as well. The camera takes either the way of OSD menu setting or the way of bottom DIP switch setting. They override each other. After the camera is turned on, the camera takes the last setting before it is turned on, either set through the OSD or bottom DIP switch. 4.
Adjusting and Setting with Menus NOTE: In some product models, only use “←” button on the infrared remote controller to change the value. To confirm the value, you can use either “→” button or HOME button. About On-Screen Menus You can change various settings, such as shooting conditions and system setup of the camera, while observing menus displayed on a connected computer screen. Control Button You can select the item by pressing “↑, ↓, ←, →” and HOME button.
OSD available only when the AE mode is set to “Full Auto.” The initial setting is “Auto Slow Shutter Off.” EXPOSURE MENU: IRIS PRI EXPOSURE MODE IRIS PRI WHITE BALANCE IRIS F1.6 PICTURE 1 GAIN LIMIT 21.4dB EX COMP OFF S. SHUTTER LIMIT: When the subject becomes dark, the shutter speed becomes slow and the gain is increased. This is a function to put a limit on the shutter speed. It prevents the camera shake when you shoot a moving subject in a dark place.
PICTURE1 Menu Push Trigger), assuming that a white subject, in correct lighting conditions, and occupying more than 1/2 of the image, is submitted to the camera. One Push White Balance data is lost when the power is turned off. If the power is turned off, reset One Push White Balance. OSD NOTE: When you select the OPW (One Push White Balance) Perform the following operations: 1. 2. Place an image of white subject (For example: A piece of white paper) in the center of the screen.
PICTURE2 Menu OSD PAN TILT ZOOM Menu OSD PICTURE 2 MENU PAN TILT ZOOM MENU EXPOSURE CHROMA OFF EXPOSURE DIGITAL ZOOM OFF WHITE BALANCE HLC MODE OFF WHITE BALANCE ZOOM RATIO OSD OFF PICTURE 1 BACKLIGHT COM.
SYSTEM Menu 10 8 0 P : 6 0/ 59.94 / 5 0/ 3 0/ 2 9.9 7/ 2 5,10 8 0 I : 6 0/ 59.94 / 5 0, 720P:60/59.94/50/30/25 SYSTEM MENU ON PAN TILT ZOOM FACTORY RESET SYSTEM RELOAD PRESET 1 ON AUTO FOCUS NORMAL FORMAT 1080p29.97 SV V0B1100S36[...] NOTE: The camera video format can be changed by setting bottom DIP switch as well. Operation Using the Infrared Remote Controller PELCO ID: When using RS485 (PELCO P/D) control, Set Camera ID to the address that you want to control to.
Operating Multiple Cameras with the Infrared Remote Controller you change the direction of the camera while checking the picture on the screen. In such a case, press the 2 (REV) button while holding down the L/R DIRECTION SET button. Arrow Button Movement of the Camera Setting MENU POWER L/R DIRECTION SET While holding down CAMERA SELECT CAMERA SELECT REV Press To reset the setting To reset the setting, press the 1 (STD) button while holding down the L/R DIRECTION SET button.
Storing the Camera Settings in Memory — the Presetting Feature Recalling the stored settings: Press any of the POSITION buttons, 1] to [6], in which you have stored the settings. CAMERA SELECT Memory (Preset) STD Using the preset function, 6 sets of camera shooting conditions can be stored and recalled. 6 sets of camera shooting conditions can be stored and recalled by using remote controller. Up to 128 presets via protocol programming.
Dimensions Unit: mm 46.5 154.5 105.7 112 145 154.5 98 97.2 94.9 14 154.
WELCOME TO THE FUTURE. bird-dog.tv hello@bi rd-dog.
