US E R MAN UAL
AFRAME A-Frame & V-Frame User Manual Please read this manual very carefully before using the product. The manual contains important instructions for the safe use and longevity of your bike. If you need any type of support or warranty information for your BirdBike, please contact us before returning it back to wherever you purchased it. The BirdBike Support Team is ready to help you via phone or email and you can also visit support.bird.co for more info.
1 Assembly Prep Frame Handlebar Saddle To prepare for the assembly of your BirdBike, first take out all pieces of the BirdBike from the box and remove all packaging. Also, open the accessory box and remove all tools, parts and everything else that’s inside of it. Tail light Front light Front fender Rear fender Rear rim Front rim Tire 2.
2 Install the handlebar 2.5 mm Allen key Y-wrench Remove Display from the Handlebar Install the Handlebar Use the 2.5mm Allen Key to remove the screw that’s behind Use the 5mm end of the Y-wrench to remove the hex bolt from inside the steerer tube and insert the handlebar over the steerer tube. the display on the handlebar. If the display isn’t easily removed from the handlebar, use the hex key to gently push it from the back of the handlebar through the hole from where the screw was removed.
3 Attach the front fender Attach the front fender to the fork by using the screws that are already in the fork legs. Use the 4mm end of the Y-wrench to remove the two screws from the fork legs and then tighten the screws through the holes at the end of the fender mounts. Using the 4mm end of the Y-wrench remove the screw that’s on the top of the backside of the fork and tighten the screw through the fender mount bracket on top of the fender so that it’s secured tightly to the back ack of the fork.
5 Adjust the saddle Remove the cap that’s covering the seat clamp screw, which is located just below the seat. Insert the seat post into the seat tube. To adjust the height, ght, move it to where it feels comfortable, then tighten the seat clamp screw with the 5mm end of the Y-wrench. Be sure to replace the cap once the seat at post is set and tightened. Warning: do not extend the seat post farther than the minimum insertion line that is indicated on the seat post.
Install the display 2.5 mm Allen key VFRAME For the final step before powering on your BirdBike, reinstall the display back into the handlebar so that the Bird logo is at the bottom. Be sure to not pinch the cable inside of the handlebar while reinstalling. Once reinstalled, use the 2.5mm Allen key to replace and tighten the screw under the display so that it’s tightened into place inside of the handlebar.
1 Assembly Prep Frame To prepare for the assembly of your BirdBike, first take out all pieces of the BirdBike from the box and remove all packaging. Also, open the accessory box and remove all tools, parts and everything else that’s inside of it. Saddle Rear fender Rear rim Handlebar Front light Front fender Front rim Tire Tail light 2.
2 Install the handlebar Y-wrench 2.5 mm Allen key Remove Display from the Handlebar Install the Handlebar Use the 2.5mm Allen Key to remove the screw that’s behind Use the 5mm end of the Y-wrench to remove the hex bolt from inside the steerer tube and insert the handlebar over the steerer tube. the display on the handlebar. If the display isn’t easily removed from the handlebar, use the hex key to gently push it from the back of the handlebar through the hole from where the screw was removed.
3 Attach the front fender Attach the front fender to the fork by using the screws that are already in the fork legs. Use the 4mm end of the Y-wrench to remove the two screws from the fork legs and then tighten the screws through the holes at the end of the fender mounts. Using the 4mm end of the Y-wrench remove the screw that’s on the top of the backside of the fork and tighten the screw through the fender mount bracket on top of the fender so that it’s secured tightly to the back of the fork.
5 Attach the pedals Wrench Install the left and right pedals by screwing them into the crank. Pay attention to which pedal is being installed on the left and the right as the left pedal is reverse threaded so it is tightened counter-clockwise. You can tell the two pedals apart by looking for the “R” on the right pedal and “L” on the left. After the pedals are screwed on by hand, use the 15mm end of the wrench to give the pedals a final tightening. Pedals 6 Install the display 2.
F U N CT I O N S OV E R V I E W Battery capacity display Speed display Power button Walk mode Switch between mph and km/h Assist level Operating Options POWER ONOFF WA L K M O D E After long pressing the power button, the BirdBike will be turned on. While the power is on, press and hold the power button again to turn off the power. After pressing and holding the - button for 2 seconds the BirdBike will go into Walk Mode.
TURN ONOFF THE HEADLIGHTS B AT T E R Y L E V E L SETTINGS MODE MPH & KMH P1 Press and hold the + key for 2 seconds to turn on the headlight. When the headlight is on, the display brightness will also automatically dim. Whenever natural lighting is insufficient (such as in bad weather) or when riding in the dark, you should always turn on the headlight. Press and hold the + key again for 2 seconds to switch off the headlight.
WHEEL DIAMETER P3 D I S P L AY B R I G H T N E S S P 4 A U TO M AT I C P O W E R O F F T I M E R P 5 SERVICE REMINDER: When P3 is displayed in the speed position while in Settings Mode, the wheel diameter setting will be shown in inches and can be adjusted with the +/- buttons. Be sure to know the proper sizes as selecting the wrong size can result in unexpected speeds. After selecting, press the power button so save.
Operation and Safety Instructions READ BEFORE RIDING • Do not drive under the influence of alcohol. • Anyone who suffers from diseases such as hypertension, hernia, concussion, epilepsy, and cardiovascular disease For your personal safety, you must pay attention to the following safe use of the BirdBike: • It is recommended to always wear a helmet when riding. • Do not exceed the maximum load of 265 lbs (120.2 kg) and no more than one rider at a time.
Maintenance and general troubleshooting Inspection of handlebar and front & rear wheel: Inspection of front and rear brakes • Move the BirdBike up, down, front, back, left and right to check • Adjustment of the brake lever: Pinch the front and rear brake whether the handlebars and the axle nuts of the front and rear levers, and confirm whether the brakes are working when the wheels are tightened properly, whether the handlebars are distance between the brake lever and the handlebar is ½ inch.
BirdBike Limited Manufacturer’s Warranty FCC Statement The BirdBike comes with a limited manufacturer’s warranty This device complies with Part 15 of the FCC rules. Operation is -Consult the dealer or an experienced radio/TV technician for and is covered from any defects or issues that are outside of subject to the following two conditions: 1) this device may not help.
ISED Statement Prop 65 Warning This device contains licence‐exempt transmitter(s)/receiv- This product can expose you to chemicals including chromium, er(s) that comply with Innovation, Science and Economic which is known to the State of California to cause cancer and Development Canada’s licence‐exempt RSS(s). Operation is birth defects or other reproductive harm. subject to the following two conditions: (1) This device may not For more information go to: http://www.p65warnings.ca.gov.
Questions? We’ve got answers. Visit support.bird.co for more info. Phone: 1-888-309-3702 (M-F 9a-5p EST) Email: BirdBike@bird.
