7 PC SOFA SET ASSEMBLY INSTRUCTIONS CUSTOMER SERVICE INFORMATION THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
* ASSEMBLE YOUR UNIT IN AN AREA FREE FROM ANY OBJECTS THAT MIGHT SCRATCH THE SURFACE OF YOUR UNIT. * EXAMINE ALL PACKING MATERIAL BEFORE DISCARDING, SHORTAGES MAY OCCUR FROM PARTS LEFT IN THE PACKING MATERIAL. * PLEASE READ THE INSTRUCTIONS CAREFULLY, AND VERIFY ALL PARTS ARE INCLUDED. * ALL BOLTS AND SCREWS NEED TO BE TIGHTENED FROM TIME TO TIME TO AVOID DAMAGE. LIST OF WOODEN PARTS NO.
TEP 1 FRONT B Metal pin Attach right and left side frames (Al & Anton back support (B) and back apron (D2). Secure using 3 1/2" into back support and 2* bolts (F) into bag apron as shown. * DO NOT TIGHTEN BOLTS YET. TEP 2 B Cc FRONT Attach front apron (D1) into side frames and s using 2" bolts (F). { Apron with round edge mn attached in front ) Next, put the seat (C) into side frames. STEP 3 Lay down the chair and secure the seat using 1" screws (G) as shown. Tighten using screwdriver. Upright the chair.
* ASSEMBLE YOUR UNIT IN AN AREA FREE FROM ANY OBJECTS THAT MIGHT SCRATCH THE SURFACE OF YOUR UNIT. * EXAMINE ALL PACKING MATERIAL BEFORE DISCARDING, SHORTAGES MAY OCCUR FROM PARTS LEFT IN THE PACKING MATERIAL. * PLEASE READ THE INSTRUCTIONS CAREFULLY, AND VERIFY ALL PARTS ARE INCLUDED. * ALL BOLTS AND SCREWS NEED TO BE TIGHTENED FROM TIME TO TIME TO AVOID DAMAGE. LIST OF WOODEN PARTS NO.
STEP 1 Attach the back support (B) and back apron (D2) into right and left side frames (Al & A2). Secure using 3 1/2" bolts (E) into D2 ‘back support and 2" bolts (F) into back support as shown. F ** DO NOT TIGHTEN BOLTS YET. STEP 2 TEP 3 od] Next, attach the front apron (D1) into right and le; frames (Al & A2). Secure front apron using 2" bolts (F) as shown. ide Secure the seat (C) using 1 1/2" screw (G) into front apron and 1" screws (H) into side frames and back apron.
IMPORTANT ! * ASSEMBLE YOUR UNIT IN AN AREA FREE FROM ANY OBJECTS THAT MIGHT SCRATCH THE SURFACE OF YOUR UNIT. * EXAMINE ALL PACKING MATERIAL BEFORE DISCARDING, SHORTAGES MAY OCCUR FROM PARTS LEFT IN THE PACKING MATERIAL. * PLEASE READ THE INSTRUCTIONS CAREFULLY, AND VERIFY ALL PARTS ARE INCLUDED. * ALL NUTS AND SCREWS NEED TO BE TIGHTENED FROM TIME TO TIME TO AVOID DAMAGE. A B Cc LIST OF WOODEN PARTS NO.
STEP 1 Attach the leg frames (B) into each corner of table top (A). Assemble the washers (D), Spring washers (E) and nuts (F) to leg frames (B). Tighten the nut using wrench. Next, attach the table support (C) into each corner of leg frames and secure using 1 1/4" screws (G) as diagram shown. Make sure all parts are correctly connected and tighten all screws using screwdriver. THE COFFEE TABLE IS NOW READY FOR USE.
IMPORTANT ! * ASSEMBLE YOUR UNIT IN AN AREA FREE FROM ANY OBJECTS THAT MIGHT SCRATCH THE SURFACE OF YOUR UNIT. * EXAMINE ALL PACKING MATERIAL BEFORE DISCARDING, SHORTAGES MAY OCCUR FROM PARTS LEFT IN THE PACKING MATERIAL. * PLEASE READ THE INSTRUCTIONS CAREFULLY, AND VERIFY ALL PARTS ARE INCLUDED. * ALL NUTS AND SCREWS NEED TO BE TIGHTENED FROM TIME TO TIME TO AVOID DAMAGE. A B LIST OF WOODEN PARTS NO.
Attach the leg frames (B) into each corner of table top (A). Assemble the washers (D), Spring washers (E) and nuts (F) to leg frames (B). Tighten the nuts using wrench. STEP 2 Next, attach the table support (C) into each corner of leg frames and secure using 1 1/4" screws (G) as diagram shown. Make sure all parts are correctly connected and tighten all screws using screwdriver. THE END TABLE IS NOW READY FOR USE.
* ASSEMBLE YOUR UNIT IN AN AREA FREE FROM ANY OBJECTS THAT MIGHT SCRATCH THE SURFACE OF YOUR UNIT. * EXAMINE ALL PACKING MATERIAL BEFORE DISCARDING, SHORTAGES MAY OCCUR FROM PARTS LEFT IN THE PACKING MATERIAL. * PLEASE READ THE INSTRUCTIONS CAREFULLY, AND VERIFY ALL PARTS ARE INCLUDED. * ALL BOLTS AND SCREWS NEED TO BE TIGHTENED FROM TIME TO TIME TO AVOID DAMAGE. LIST OF WOODEN PARTS NO.
EP 1 FRONT Attach the aprons (C) and stool (B) into leg frames (A) and secure using 2" bolts (D). ( Apron with round edge must attached in front ) Tighten the bolts using screwdriver. STEP 2 TEP 3 Cushion Make sure all parts are correctly connected and tighten E all bolts and screws completely using s driver. Tapping in the wooden caps (F) to cover bolts head using rubber mallet. 8 the seat using 1"screws (E) as shown, Install the cushion. Tighten screws using screwdriver. right the stool.
