Biostar T-Series TForce4/ TForce4 U FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents PACKAGE CHECKLIST ............................................................................... I CHAPTER 1: INTRODUCTION ...................................................... 1 1.1 1.2 MOTHERBOARD FEATURES ............................................................1 LAYOUT AND COMPONENTS ...........................................................3 CHAPTER 2: HARDWARE INSTALLATION ............................... 4 2.1 2.2 2.3 INSTALLING CENTRAL PRIOCESSING UNIT (CPU)...............
Biostar T-Series TForce4/ TForce4 U CHAPTER 1: INTRODUCTION 1.1 MOTHERBOARD FEATURES CPU Supports Socket 939. Supports AMD Athlon 64 FX / Athlon 64 /Athlon 64 X2 processors. Supports AMD Sempron processor. AMD 64 architecture enables simultaneous 32 and 64 bit computing. Supports HyperTransport and AMD Cool’n’Quiet Technology. Chipset NVIDIA nForce4 for TForce4 NVIDIA nForce4 Ultra for TForce4 Ultra. Both support: Supports NVIDIA Firewall. Supports Gigabit Ethernet. Supports NVIDIA nTune Utility.
Biostar T-Series TForce4/ TForce4 U AC’9 7 Audio Sound Codec Chip: ALC850, supports 8 channels audio output. IEEE 1394A Chip Chip: VIA VT6307, supports 2 ports with transfer up to 400Mb/s. Gigabit Ethernet LAN NVIDIA Gigabit MAC + VITESSE Gigabit PHY VSC8201. Supports ACPI power management. Supports NVIDIA StreamThru technology Isochronous controller paired with Hyper Transport results in fastest networking performance.
Biostar T-Series 1.
Biostar T-Series TForce4/ TForce4 U CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PRIOCESSING UNIT (CPU) A. Central Processing Unit (CPU) Step 1: Remove the socket protection cap. Step 2: Pull the lever toward direction A from the socket and then raise the lever up to a 90-degree angle. 90 A Step 3: Look for the white triangle on socket, and the gold triangle on CPU should point forwards this white triangle. The CPU will fit only in the correct orientation.
Biostar T-Series TForce4/ TForce4 U Step 4: Hold the CPU down firmly, and then close the lever toward direct B to complete the installation. B Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN power cable to the JCFAN1. This completes the installation. B.
Biostar T-Series 2.2 TForce4/ TForce4 U SYSTEM MEMORY DIMM3 DIMM1 DIMM4 DIMM2 A. Memory Modules 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snaps back in place and the DIMM is properly seated.
Biostar T-Series TForce4/ TForce4 U C. DDR Installation Notice For AMD K8 939 CPU launched before Rev. E, please follow the table below to install your DDR memory module, or the system may not boot up or may not function properly. (Please refer to Table 1 for CPU Revision) “SS” represents Single Side DDR memory module. “DS” represents Double Side DDR memory module. Star sign “*” represents leave the DIMM socket empty.
Biostar T-Series 2.3 TForce4/ TForce4 U PERIPHERALS A. Card and I/O Slots: Floppy Disk Connector: FDD1 The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables. 2 34 1 33 Hard Disk Connectors: IDE1/IDE2 The motherboard has two 32-bit Enhanced PCI IDE Controllers that provide PIO Mode 0~5, Bus Master, and Ultra DMA 33/66/100/133 functionality.
Biostar T-Series TForce4/ TForce4 U Peripheral Component Interconnect Slots: PCI1~PCI3 This motherboard is equipped with 3 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PCI1 PCI2 PCI3 PCI-Express Slots: PCI-EX16/ PEX1_2/ PEX1_1 PCI-EX16: PCI Express 1.0a compliant. Maximum bandwidth is up to 4GB/s per direction. PEX1_2/ PEX1_1: PCI Express 1.0a compliant.
Biostar T-Series TForce4/ TForce4 U Xtreme Graphics Port Slot: XGP1 This XGP (Extreme Graphics Port) slot is a special design that only supports compatible AGP VGA cards. To install the system with an add-on AGP VGA card, please make sure to install the driver of add-on AGP VGA card before onboard VGA driver installation. If the onboard VGA driver has already been installed before you install the add-on AGP VGA card, the system will automatically set the onboard VGA as the primary graphics adapter.
Biostar T-Series TForce4/ TForce4 U B. Connectors and Headers: How to setup Jumpers The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “closed”, if not, that means the jumper is “open”. Pin opened Pin closed ATX Power Source Connector: JATXPWR1 Pin1-2 closed JATXPWR1 allows user to connect 24-pin power connector on the ATX power supply. 13 1 24 12 Pin Assignment Pin Assignment 13 14 15 16 17 18 19 20 21 22 23 24 +3.
Biostar T-Series TForce4/ TForce4 U ATX Power Source Connector: JATXPWR2 By connecting JATXPWR2, it will provide +12V to CPU power circuit. 1 2 3 4 Pin 1 2 3 4 Assignment +12V +12V Ground Ground Power Source Header for PS/2 Keyboard/Mouse: JKBMSV1 Pin 1-2 Close: +5V for PS/2 keyboard and mouse. (Factory default setting) Pin 2-3 Close: PS/2 keyboard and mouse are powered with +5V standby voltage.
Biostar T-Series TForce4/ TForce4 U Front Panel Audio-out Header: JAUDIO2 This connector will allow user to connect with the front audio output headers on the PC case. It will disable the output on back panel audio connectors.
Biostar T-Series TForce4/ TForce4 U Headers for USB Ports at Front Panel: JUSB1~JUSB3 This connector allows user to connect additional USB cables at PC front panel, and also can be connected with internal USB devices, like USB card reader. Pin 1 2 3 4 5 JUSB1 JUS B2 JUSB3 6 9 1 7 10 2 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC Power Source Headers for USB Ports: J1394_USBV1/JUSBV1 Pin 1-2 Close: J1394_USBV1: +5V for USB ports at J1394_USB1 and JUSBLAN1.
Biostar T-Series TForce4/ TForce4 U Digital Audio-out Connector: JSPDIF_OUT This connector allows users to connect the PCI bracket SPDIF output header. Pin 1 2 3 3 Assignment +5V SPDIF OUT Ground 1 Serial ATA Connectors: JSATA1~JSATA4 The motherboard has an SATA Controller in nForce4 CK8-04 and CK8-04 Ultra with 4 channels SATA interface, it satisfies the SATA 1.0 with transfer rate of 1.5 Gb/s and SATA 2.0 spec with transfer rate of 3.0 Gb/s.
Biostar T-Series TForce4/ TForce4 U Case Open Header: JCI1 This connector allows system to monitor PC case open status. If the signal has been triggered, it will record to the CMOS and show the message on next boot-up. Pin Assignment 1 Case open signal 2 Ground 1 2 Clear CMOS Header: JCMOS1 By placing the jumper on pin 2-3, it allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard.
Biostar T-Series TForce4/ TForce4 U J1394A1: Header for 1394 Firewire Port at Front Panel This header allows user to connect the digital image device, like DV, D8, or V8, etc. 9 1 10 2 Pin 1 2 3 4 5 6 7 8 9 10 Assignment A+ AGround Ground B+ B+12V +12V Key Ground J1394PWR1: Power Source for 1394 Firewire Port 3 1 Pin 1-2 close +3.3V for 1394 chipset (Default). 3 3 17 1 1 Pin 2-3 close +3.3V SB for 1394 chipset.
Biostar T-Series TForce4/ TForce4 U On-Board LED Indicators There are 2 LED indicators on the motherboard to show system status. LED_D1 LED_D2 LED_DIMM LED_5SB LED_D1 and LED_D2: These 2 LED indicate system power on diagnostics. Please refer to the table below for different messages: LED_D1 ON ON OFF OFF LED_D2 ON OFF ON OFF Message Normal Memory Error VGA Error Abnormal: CPU / Chipset error. LED_DIMM: This LED indicates the voltage of memory is activated normally.
Biostar T-Series TForce4/ TForce4 U CHAPTER 3: NVIDIA RAID FUNCTIONS 3.1 OPERATION SYSTEM Supports Windows XP Home/Professional Edition, and Windows 2000 Professional. 3.2 RAID ARRAYS NVRAID supports the following types of RAID arrays: RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications. RAID 1: RAID 1 defines techniques for mirroring data. RAID 0+1: RAID 0+1 combines the techniques used in RAID 0 and RAID 1.
Biostar T-Series 3.3 TForce4/ TForce4 U HOW RAID WORKS RAID 0: The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth.
Biostar T-Series TForce4/ TForce4 U RAID 1: Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure.
Biostar T-Series TForce4/ TForce4 U RAID 0+1: RAID 0 drives can be mirrored using RAID 1 techniques. Resulting in a RAID 0+1 solution for improved performance plus resiliency. Features and Benefits - - Data 1 Data 3 Data 5 ※ Drives: Minimum 4, and maximum is 6 or 8, depending on the platform. Benefits: Optimizes for both fault tolerance and performance, allowing for automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks.
Biostar T-Series TForce4/ TForce4 U CHAPTER 4: OVERCLOCK QUICK GUIDE 4.1: T-POWER INTRODUCTION Biostar T-Power is a whole new utility that is designed for overclock users. Based on many precise tests, Biostar Engineering Team (BET) has developed this ultimate overclock engine to raise system performance. No matter whether under BIOS or Windows interface, T-Power is able to present the best system state according to users’ overclock setting. T-Power BIOS Features: Overclocking Navigator Engine (O.N.E.
Biostar T-Series 4.2: TForce4/ TForce4 U T-POWER BIOS FEATURE A. Overclocking Navigator Engine (O.N.E.): ONE provides two powerful overclocking engines: MOS and AOS for both Elite and Casual overclockers. Manual Overclock System (M.O.S.) MOS is designed for experienced overclock users. It allows users to customize personal overclock settings.
Biostar T-Series TForce4/ TForce4 U CPU Overclock Setting: CPU Voltage: This function will increase CPU stability when overclocking. However, the CPU temperature will increase when CPU voltage is increased. Choices: The range is from 1.2V to 1.725V, with an interval of 0.0.25V. CPU Frequency: CPU Frequency is directly in proportion to system performance. To maintain the system stability, CPU voltage needs to be increased also when raising CPU frequency.
Biostar T-Series TForce4/ TForce4 U Notice: According to tests that have been done; AMD Athlon XP 3000+ CPU is the best CPU type for overclock function. Automatic Overclock System (A.O.S.) For beginners in overclock field, BET had developed an easy, fast, and powerful feature to increase the system performance, named A.O.S. Based on many tests and experiments, A.O.S. provides 3 ideal overclock configurations that are able to raise the system performance in a single step.
Biostar T-Series TForce4/ TForce4 U V8 Tech Engine: This setting will raise about 15%~25% of whole system performance. V12 Tech Engine: This setting will raise about 25%~30% of whole system performance. Notices: 1. Not all types of AMD CPU perform above overclock setting ideally; the difference will be based on the selected CPU model. 2. From BET experiments, the Atholon64 FX CPU is not suitable for this A.O.S. feature.
Biostar T-Series TForce4/ TForce4 U B. CMOS Reloading Program (C.R.P.): It allows users to save different CMOS settings into BIOS-ROM. Users are able to reload any saved CMOS setting for customizing system configurations. Moreover, users are able to save an ideal overclock setting during overclock operation. There are 50 sets of record addresses in total, and users are able to name the CMOS data according to personal preference.
Biostar T-Series TForce4/ TForce4 U C. Memory Integration Test (M.I.T.): This function is under “Overclocking Navigator Engine” item. MIT allows users to test memory compatibilities, and no extra devices or software are needed. Step 1: The default setting under this item is “Disabled”; the condition parameter should be changed to “Enable” to proceed this test. ↓ Step 2: Save and Exit from CMOS setup and reboot the system to activate this test.
Biostar T-Series TForce4/ TForce4 U D. Self Recovery System (S.R.S.): This function can’t be seen under T-Power BIOS setup; and is always on whenever the system starts up. However, it can prevent system hang-up due to inappropriate overclock actions. When the system hangs up, S.R.S. will automatically log in the default BIOS setting, and all overclock settings will be re-configured. E. Integrated Flash Program (I.F.P.): IFP is a safe and quick way to upgrade BIOS.
Biostar T-Series TForce4/ TForce4 U CPU Fan Start <℃> The CPU fan starts to work when CPU temperature arrives to this set value. The range is from 0℃~127℃, with an interval of 1℃. Choices: 32℃ (default). CPU Fan Full speed <℃> When CPU temperature arrives to the set value, the CPU fan will work under Full Speed. The range is from 0℃~127℃, with an interval of 1℃. Choices: 52℃ (default). Start PWM Value When CPU temperature arrives to the set value, the CPU fan will work under Smart Fan Function mode.
Biostar T-Series 4.3 TForce4/ TForce4 U T-POWER WINDOWS FEATURE A.Hardware Monitor: T-Power Hardware monitor allows users to monitor system voltage, temperature and fan speed accordingly. Additionally, a rescue action will be taken by the program automatically while the system faces an abnormal condition. The program will trigger an alarm or shut down the system when unpredictable errors occur. All the monitoring items are illustrated by a waveform diagram. Hardware Monitor Toolbar i.
Biostar T-Series TForce4/ TForce4 U CPU Temperature This column configures the CPU temperature. There is a waveform to represent the status of CPU temperature. By adjusting , users can easily configure the upper limit of CPU temperature for system operating. In this diagram, the white line represents the upper limit which user-set for CPU temperature and the green line shows present CPU temperature.
Biostar T-Series TForce4/ TForce4 U CPU/Battery Voltage i. VCore This item displays the CPU voltage, represented by a light blue line. Users can set the upper and lower limit by adjusting to monitor the CPU operating voltage. If CPU voltage is higher or lower than the set value, the status line will change into a red warning line, and a warning sound will change to . will alert you. Also, the system tray icon ii. VBAT This item displays the CMOS battery voltage, represented by a light green line.
Biostar T-Series TForce4/ TForce4 U B. Overclocking Configurations This diagram is designed for T-series Overclocking utility. Friendly interface and solid overclock features are the major concept of this utility. Graphic 1 will appear when activating this utility. Graphic 1 A. Clicking on “Biostar” will lead you to the Biostar Homepage. B. This column shows the CPU speed information. C. Click on this button and the utility will pop-up 4 sub-screens (Please refers to Graphic 3). D.
Biostar T-Series TForce4/ TForce4 U CPU Overclocking Settings: By adjusting can configure three items for CPU overclocking. A. CPU Frequency Range: 133MHz~450MHz. Interval: 1MHz. B. CPU Ratio Range: 4~25. Interval: 1. C. CPU Voltage Range: 1.175V~1.725V. Interval: 0.025V. Memory Overclocking Settings: By adjusting can configure two items for Memory overclocking. A. Memory Clock Frequency Choices: 100, 133, 166, 200, 233, 250. B. Memory Voltage Range: 2.5V~2.8V. Interval: 0.1V.
Biostar T-Series TForce4/ TForce4 U PCI Overclocking Setting: This diagram shows present PCI working status and helps to monitor PCI peripherals working status. This item cannot be adjusted.
Biostar T-Series TForce4/ TForce4 U C. Smart Fan Function When Smart Fan Function is activated, screens will pop-up to illustrate the fan speed information. i. CPU Temperature: Show current CPU temperature. ii. CPU Fan speed: Show current CPU Fan speed. iii. System Fan speed: Show current system Fan speed. iv. Calibrate: When changing CPU Fan or System Fan, click on this button to re-calibrate the Fan speed. Note: 1. 2.
Biostar T-Series v. TForce4/ TForce4 U Auto: If the green indicator is lit up, the Smart Fan Function is “On” (Default Setting). Click on this button again to close Smart Fan Function, and a screen as below would pop-up. There will be pulling-meter besides the CPU Fan and System Fan, the CPU Fan and the System Fan speed can be adjusted by adjusting the Cursor Up or Down. vi. Program Tool Bar: z About: Click on this button to get program-related information.
Biostar T-Series TForce4/ TForce4 U D. Live Update When Live Update program is activated, a screen will pop up to illustrate BIOS related information. i. Link to Internet: Click on this button will link to Biostar website and BIOS file will be downloaded. ii. Update BIOS: Click on this button to run BIOS flashing process, and it’s easy and safe. iii. Backup BIOS: Click on this button, and BIOS file will be saved into the user-selected folder. iv.
Biostar T-Series TForce4/ TForce4 U CHAPTER 5: USEFUL HELP 5.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.
Biostar T-Series TForce4/ TForce4 U Manual Aside from the paperback manual, we also provide manual in the Driver CD. Click on the Manual icon to browse for available manual. Note: You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep2.html 5.
Biostar T-Series 5.3 TForce4/ TForce4 U EXTRA INFORMATION A. BIOS Update After you fail to update BIOS or BIOS is invaded by a virus, the Boot-Block function will help to restore BIOS. If the following message is shown after boot-up of the system, it means the BIOS contents are corrupted. In this case, please follow the procedure below to restore the BIOS: 1. Make a bootable floppy disk. 2. Download the Flash Utility “AWDFLASH.exe” from the Biostar website: www.biostar.com.tw 3.
Biostar T-Series B. TForce4/ TForce4 U CPU Overheated If the system shuts down automatically after power on of system for a few seconds that means the CPU protection function has been activated. When the CPU is overheated, the motherboard will shutdown automatically to avoid damaging the CPU, and the system will not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotating normally. 3.
Biostar T-Series 5.4 TForce4/ TForce4 U TROUBLESHOOTING Problem Solution 1. No power to the system at all Power light don’t illuminate, fan inside power supply does not turn on. 2. Indicator light on keyboard does not turn on. 1. 2. 3. System inoperative. Keyboard lights are on, power indicator lights are lit, and hard drive is spinning. Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place. 1.
Biostar T-Series TForce4/ TForce4 U GERMAN CPU Unterstützt Sockel 939. Unterstützt AMD Athlon 64 FX- / Athlon 64- / Athlon 64 X2-Prozessoren. Unterstützt AMD Sempron -Prozessoren. AMD 64-Architektur ermöglicht 32- und 64-Bit-Verarbeitung. Unterstützt HyperTransport™- ud AMD Cool’n’Quiet™-Technologie. Chipsatz NVIDIA nForce4 (TForce4). NVIDIA nForce4 Ultra (TForce4 Ultra). Unterstützung: Unterstützt NVIDIA Firewall. Unterstützt Gigabit Ethernet. Unterstützt NVIDIA nTune Utility.
Biostar T-Series TForce4/ TForce4 U AC’97 Sound-Codec Chip: ALC850, unterstützt 8 Kanäle. IEEE 1394A Chip Chip: VIA VT6307, unterstützt zwei 1394A Firewire-Anschlüsse jeweils mit einer Geschwindigkeit von bis zu 400Mb/s. Gigabit Ethernet-LAN NVIDIA Gigabit MAC + VITESSE Gigabit PHY VSC8201. Unterstützt die ACPI-Energieverwaltung. Unterstützt NVIDIA StreamThru-Technologie Isochroner Controller gekoppelt mit Hyper Transport garantiert höchste Netzwerkleistung.
Biostar T-Series TForce4/ TForce4 U FRENCH Processeur Supporte le socket 939. Supporte les processeurs AMD Athlon 64 FX / Athlon 64 /Athlon 64 X2. Prise en charge des processeurs AMD Sempron. Architecture AMD 64 activant des operations 32 et 64 bits. Supporte les technologies HyperTransport™ et AMD Cool’n’Quiet™. Chipset NVIDIA nForce4 (TForce4). NVIDIA nForce4 Ultra (TForce4 Ultra). Tous deux prennent en charge: Supporte le firewall NVIDIA. Supporte l’éthernet Gigabit.
Biostar T-Series TForce4/ TForce4 U Codec audio AC’97 Chip: ALC850, prise en charge 8 canaux. Chip IEEE 1394 Chip: VIA VT6307, prise en charge de deux ports 1394A Firewire jusqu'à 400Mo/s par port. LAN Ethernet Gigabit NVIDIA Gigabit MAC + VITESSE Gigabit PHY VSC8201. Prise en charge Gestion de l'alimentation ACPI. Prise en charge de la technologie NVIDIA StreamThru Contrôleur isochrone couple l'Hyper Transport donnant des performances réseau plus rapides.
Biostar T-Series TForce4/ TForce4 U ITALIAN CPU Supporto di Socket 939. Supporto di processori AMD Athlon 64 FX / Athlon 64 / Athlon 64 X2. Supporto processore AMD Sempron. L’architettura AMD 64 abilita la computazione simultanea 32 e 64 bit. Supporto delle tecnologie HyperTransport™ e AMD Cool’n’Quiet™. Chipset NVIDIA nForce4 (TForce4). NVIDIA nForce4 Ultra (TForce4 Ultra). Entrambi supportano: Supporto di NVIDIA Firewall. Supporto di Gigabit Ethernet. Supporto di NVIDIA nTune Utility.
Biostar T-Series TForce4/ TForce4 U Chip: VIA VT6307, supporto di due porte Firewire 1394A con capacità massima individuale di 400Mb/s. Gigabit Ethernet LAN NVIDIA Gigabit MAC + VITESSE Gigabit PHY VSC8201. Supporto gestione energetica ACPI. Supporto della tecnologia NVIDIA StreamThru Il controller isocrono accoppiato con Hyper Transport produce le più veloci prestazioni di rete.
Biostar T-Series TForce4/ TForce4 U SPANISH Procesador Soporta el Socket 939. Supporta los procesadores AMD Athlon 64 FX / Athlon 64 /Athlon 64 X2. Compatible con el procesador AMD Sempron. La arquitectura AMD 64 permite computación de 32 bits y 64 bits de manera simultánea. Suporta las tecnologías HyperTransport™ y AMD Cool’n’Quiet™. Conjunto de chips NVIDIA nForce4 (TForce4). NVIDIA nForce4 Ultra (TForce4 Ultra). Ambos admiten: Soporta el Firewall NVIDIA. Soporta Gigabit Ethernet.
Biostar T-Series TForce4/ TForce4 U Procesador IEEE 1394 Procesador:VIA VT6307, admite dos puertos 1394A Firewire de hasta 400 Mb/s individualmente. LAN Ethernet Gigabit NVIDIA Gigabit MAC + VITESSE Gigabit PHY VSC8201. Admite administración de energía ACPI. Admite la tecnología NVIDIA StreamThru Controlador isócrono asociado con Hyper Transport proporciona el mayor rendimiento para interconexión en red.
Biostar T-Series TForce4/ TForce4 U PORTUGUESE CPU Suporta o socket 939. Suporta processadores AMD Athlon 64 FX / Athlon 64 / Athlon 64 X2. Suporta um processador AMD Sempron. A arquitectura AMD 64 permite uma computação de 32 e 64 bits em simultâneo. Suporta a tecnologia HyperTransport™ e AMD Cool’n’Quiet™. Chipset NVIDIA nForce4 (TForce4). NVIDIA nForce4 Ultra (TForce4 Ultra). Suporte: Suporta a firewall NVIDIA. Suporta a Ethernet Gigabit. Suporta o utilitário NVIDIA nTune.
Biostar T-Series TForce4/ TForce4 U Chip IEEE 1394A Chip: VIA VT6307, suporta duas portas Firewire 1394A até 400 Mb/s para cada uma LAN Ethernet Gigabit NVIDIA Gigabit MAC + VITESSE Gigabit PHY VSC8201. Suporta a gestão de energia ACPI. Suporta a tecnologia NVIDIA StreamThru Controlador isócrono combinado com a arquitectura Hyper Transport para um desempenho mais rápido ao nível da rede.
Biostar T-Series TForce4/ TForce4 U POLAND PROCESOR Obsługa gniazd Socket 939. Obsługa procesorów AMD Athlon 64 FX / Athlon 64 / Athlon 64 X2. Obsługa procesorów AMD Sempron Architektura AMD 64 umożliwiająca jednoczesne przetwarzanie 32 i 64 bitowe. Obsługa technologii HyperTransport™ oraz AMD Cool’n’Quiet™. Chipset NVIDIA nForce4 (TForce4). NVIDIA nForce4 Ultra (TForce4 Ultra). Obsługa: Obsługa firewalla NVIDIA. Obsługa Gigabit Ethernet. Obsługa programu narzędziowego NVIDIA nTune.
Biostar T-Series TForce4/ TForce4 U Chip: VIA VT6307, obsługa dwóch portów 1394A Firewire o indywidualnej szybkości do 400Mb/s. Sieć LAN Gigabit Ethernet NVIDIA Gigabit MAC + VITESSE Gigabit PHY VSC8201. Obsługa zarządzania zasilaniem ACPI. Obsługa technologii NVIDIA StreamThru Izochroniczny kontroler sparowany z Hyper Transport, zapewnia najszybsze działanie sieci.
Biostar T-Series TForce4/ TForce4 U RUSSIAN Процессор Поддерживает гнездо 939.. Поддерживает процессоры AMD Athlon 64 FX, Athlon 64, Athlon 64 X2 Поддерживает процессорыAMD Sempron. Архитектура AMD 64 допускает одновременную работу в 32-разрядном и 64-разрядном режимах. Поддерживает технологии HyperTransport™ и AMD Cool’n’Quiet™ Набор микросхем NVIDIA nForce4 (TForce4). NVIDIA nForce4 Ultra (TForce4 Ultra). Поддерживают оба: Поддерживает Поддерживает Поддерживает Поддерживает брандмауэр NVIDIA.
Biostar T-Series TForce4/ TForce4 U Контроллер: VIA VT6307, поддерживает два порта 1394A Firewire со скростью каждого порта до 400 Мбит/с. Гигабитный интерфейс Ethernet NVIDIA Gigabit MAC + VITESSE Gigabit PHY VSC8201. Поддерживает управление питанием ACPI. Поддержка технологии NVIDIA StreamThru Изохронный контроллер, объединенный с шиной HyperTransport для обеспечения повышенной производительности в сети.
Biostar T-Series TForce4/ TForce4 U ARABIC وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ )( CPU ﺗﺪﻋﻢ ﻗﺎﻋﺪة ﺗﻮﺻﻴﻞ .939 ﺗﺪﻋﻢ ﻣﻌﺎﻟﺠﺎت .Athlon 64 X2 / Athlon 64 / AMD Athlon 64 FX ﺗﺪﻋﻢ ﻣﻌﺎﻟﺠﺎت .AMD Sempron processor ﺗﺘﻴﺢ ﺑﻨﻴﺔ AMD 64اﻟﺤﺴﺎب اﻟﻤﺘﺰاﻣﻦ 32و 64ﺑﺖ. ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ ™ HyperTransportو ™.AMD Cool’n’Quiet ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ NVIDIA nForce4 (TForce4). NVIDIA nForce4 Ultra (TForce4 Ultra). آﻼ ﻣﻨﻬﻤﺎ یﺪﻋﻢ: ﺗﺪﻋﻢ ﺡﺎﺋﻂ اﻟﺤﻤﺎیﺔ ﻋﺒﺮ اﻹﻥﺘﺮﻥﺖ "." NVIDIA ﺗﺪﻋﻢ .
Biostar T-Series TForce4/ TForce4 U ﺵﺮﻳﺤﺔ ) IEEE 1394اﺧﺘﻴﺎري( VIاﻟﺸﺮیﺤﺔ, VIA VT6307 :ﺗﺪﻋﻢ ﻣﻨﻔﺬي 1394A Firewireﺗﺼﻞ ﻗﺪرة آﻞ ﻣﻨﻬﻤﺎ إﻟﻰ 400ﻣﻴﺠﺎ ﺑﺎیﺖ/اﻟﺜﺎﻥﻴﺔ. اﻟﺸﺒﻜﺔ اﻟﻤﺤﻠﻴﺔ .VSC PHY Gigabit EESSVIT 8201 +MAC Gigabit NVIDIA ودﻋﻢ إدارة اﻟﻄﺎﻗﺔ ﻣﻦ ﺥﻼل .ACPI دﻋﻢ ﺗﻘﻨﻴﺔ NVIDIA StreamThru وﺡﺪة ﺗﺤﻜﻢ ﺗﺰاﻣﻨﻴﺔ ﻣﻘﺘﺮﻥﺔ ﺑﺘﻘﻨﻴﺔ Hyper Transportﻣﻤﺎ یﻮﻓﺮ أﺱﺮع ﻣﻌﺪل ﻷداء اﻟﺸﺒﻜﺎت.
Biostar T-Series TForce4/ TForce4 U JAPANESE CPU Socket 939 をサポート。 AMD Athlon 64 FX / Athlon 64 / Athlon 64 X2 プロセッサをサポー ト。 AMD Sempron プロセッサをサポート。 AMD 64 アーキテクチャにより、32 ビットと 64 ビットの同時コン ピューティングが可能。 HyperTransport および AMD Cool’n’Quiet テクノロジをサ ポート。 チップセット NVIDIA nForce4 (TForce4).
Biostar T-Series TForce4/ TForce4 U バス・マスターモードに対応。 AC’97 オーディオ サウンド・コデック チップ: ALC850, 8 チャンネルをサポート。 IEEE 1394 チップ チップ: VIA VT6307, 最大 400Mb/秒の 2 つの 1394A Firewire ポー トを個別にサポート。 Gigabit イーサネット LAN NVIDIA Gigabit MAC + VITESSE Gigabit PHY VSC8201。 ACPI 電源管理をサポート。 NVIDIA StreamThru テクノロジに対応 アイソクロナスコントローラとハイパートランスポート の組み合わせによる、最速のネットワーキング性能。 Security セキュリティ NVIDIA ファイアウォールテクノロジ ネーティブなファイアウォールソリューションが、不正トラ ヒックのフィルタリングによる侵入から PC を保護します。 NVIDIA Active Armor に対応 (nForce4 Ultra のみ) ネットワークのセキュリティを強化し、ユーザに速く
Biostar T-Series TForce4/ TForce4 U シリアルポート(x1) (COM2 オプション) USB 2.
TForce4 /TForce4 Ultra BIOS Setup BIOS Setup.......................................................................................... 1 1 Main Menu .......................................................................................................3 2 Standard CMOS Features ...................................................................................6 3 Advanced BIOS Features....................................................................................8 4 Advanced Chipset Features...........
TForce4 / TForce4 Ultra BIOS Setup Introduction This manual discussed Award™ Setup program built into the ROM BIOS. The Setup program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM so that it retains the Setup information when the power is turned off. The Award BIOS™ installed in your computer system’s ROM (Read Only Memory) is a custom version of an industry standard BIOS.
TForce4 / TForce4 Ultra Supported CPUs This AWARD BIOS supports the AMD CPU. Using Setup In general, you use the arrow keys to highlight items, press to select, use the and keys to change entries, press for help and press to quit. The following table provides more detail about how to navigate in the Setup program by using the keyboard.
TForce4 / TForce4 Ultra 1 Main Menu Once you enter Award BIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions. Use the arrow keys to select among the items and press to accept and enter the sub-menu. !! WARNING !! The information about BIOS defaults on manual (Figure 1,2,3,4,5,6,7,8,9) is just for reference, please refer to the BIOS installed on board, for update information. Figure 1.
TForce4 / TForce4 Ultra PnP/PCI Configurations This submenu allows you to configure certain “Plug and Play” and PCI options. PC Health Status This submenu allows you to monitor the hardware of your system. OverClock Navigator Engine (O.N.E.) ONE provides two powerful overclock engines, MOS & AOS for both overclock expertises and beginners. Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence.
TForce4 / TForce4 Ultra Exit Without Saving Abandon all changes made during the current session and exit setup. confirmation message will be displayed before proceeding. Integrate Flashing Program This is a very safe way to upgrade BIOS. By pressing “Enter” key for three times, and the upgrading process will be completed easily.
TForce4 / TForce4 Ultra 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the or keys to select the value you want in each item. Figure 2.
TForce4 / TForce4 Ultra Main Menu Selections This table shows the selections that you can make on the Main Menu. Item Options Date mm : dd : yy Time IDE Primary Master hh : mm : ss Options are in its sub menu. Options are in its sub menu. Options are in its sub menu. Options are in its sub menu. IDE Primary Slave IDE Secondary Master IDE Secondary Slave Drive A Drive B Base Memory 360K, 5.25 in 1.2M, 5.25 in 720K, 3.5 in 1.44M, 3.5 in 2.88M, 3.
TForce4 / TForce4 Ultra 3 Advanced BIOS Features Figure 3. Advanced BIOS Setup Cache Setup These BIOS attempt to load the operating system from the device in the sequence selected in these items. CPU Internal Cache Depending on the CPU/chipset in use, you may be able to increase memory access time with this option. Enabled (default) Enable cache. Disabled Disable cache. External Cache This option enables or disables “Level 2” secondary cache on the CPU, which may improve performance.
TForce4 / TForce4 Ultra Boot Seq & Floppy Setup Hard Disk Boot Priority These BIOS attempt to load the operating system from the device in the sequence selected in these items. The Choices: Pri. Master, Pri. Slave, Sec. Master, Sec, Slave, USBHDD0, USB HDD1, USB HDD2, and Bootable Add-in Cards. First/ Second/ Third/ Boot Other Device These BIOS attempt to load the operating system from the devices in the sequence selected in these items.
TForce4 / TForce4 Ultra Boot Up Floppy Seek Enabling this option will test the floppy drives to determine if they have 40 or 80 tracks. Disabling this option reduces the time it takes to boot-up. The Choices: Enabled (default), Disabled. Virus Warning This option allows you to choose the Virus Warning feature that is used to protect the IDE Hard Disk boot sector.
TForce4 / TForce4 Ultra Security Option This option will enable only individuals with passwords to bring the system online and/or to use the CMOS Setup Utility. System A password is required for the system to boot and is also required to access the Setup Utility. Setup (default) A password is required to access the Setup Utility only. This will only apply if passwords are set from the Setup main menu. APIC MODE Selecting Enabled enables APIC device mode reporting from the BIOS to the operating system.
TForce4 / TForce4 Ultra 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system. This chipset manage bus speeds and access to system memory resources, such as DRAM. It also coordinates communications with the PCI bus. The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly. Figure 4.
TForce4 / TForce4 Ultra System BIOS Cacheable Selecting the “Disabled ” option allows caching of the system BIOS ROM at F0000h-FFFFFh which can improve system performance. However, any programs writing to this area of memory will cause conflicts and result in system errors. The Choices: Disabled (default), Enabled.
TForce4 / TForce4 Ultra 5 Integrated Peripherals Figure 5. Integrated Peripherals IDE Function Setup If you highlight the literal “Press Enter” next to the “IDE Function Setup” label and then press the enter key, it will take you a submenu with the following options: OnChip IDE Channel 0/1 The motherboard chipset contains a PCI IDE interface with support for two IDE channels. Select “Enabled” to activate the first and/or second IDE interface.
TForce4 / TForce4 Ultra Primary / Secondary /Master / Slave PIO The IDE PIO (Programmed Input / Output) fields let you set a PIO mode (0-4) for each of the IDE devices that the onboard IDE interface supports. Modes 0 to 4 will increase performance progressively. In Auto mode, the system automatically determines the best mode for each device. The Choices: Auto (default), Mode0, Mode1, Mode2, Mode3, Mode4.
TForce4 / TForce4 Ultra ONBOARD DEVICE OnChip USB This option should be enabled if your system has a USB installed on the system board. You will need to disable this feature if you add a higher performance controller. The Choices: V1. 1+V2. 0 (default), Disabled, V1.1 USB keyboard Support Enables support for USB attached keyboard. The Choices: Disabled (default), Enabled USB Mouse Support Enables support for USB attached mouse.
TForce4 / TForce4 Ultra ONBOARD IO/Address Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If install and FDC or the system has no floppy drive, select Disabled in this field. The Choices: Enabled (default), Disabled. Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports. The Choices: Disabled, 3F8/IRQ4 (default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Auto.
TForce4 / TForce4 Ultra Parallel Port Mode The default value is SPP. The Choices: SPP(default) Using Parallel port as Standard Printer Port. EPP Using Parallel Port as Enhanced Parallel Port. ECP Using Parallel port as Extended Capabilities Port. ECP+EPP Using Parallel port as ECP & EPP mode. ECP Mode Use DMA Select a DMA Channel for the port. The Choices: 3 (default), 1. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read / write.
TForce4 / TForce4 Ultra 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features. Figure 6. Power Manage ment Setup ACPI function This item displays the status of the Advanced Configuration and Power Management (ACPI). The Choices: Enabled (default), Disabled. ACPI Suspend Type The item allows you to select the suspend type under the ACPI operating system.
TForce4 / TForce4 Ultra User Define (default) Allows you to set each mode individually. When not disabled, each of the ranges are from 1 min. to 1 hr. except for HDD Power Down which ranges from 1 min. to 15 min. and disable. Video Off Method This option determines the manner in which the monitor is goes blank. V/H SYNC+Blank This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer.
TForce4 / TForce4 Ultra KB Power ON Password Input password and press Enter to set the Keyboard power on password. Hot Key Power on This option allows you to choose a hot key to power on. The Choices: Ctrl-F1 (default), Ctrl-F2, Ctrl-F3, Ctrl-F4, Ctrl-F5, Ctrl-F6, Ctrl-F7, Ctrl-F8 POWER After PWR-Fail This setting specifies whether your system will reboot after a power fail or interrupts occurs. Off Leaves the computer in the power off state. On Reboots the computer.
TForce4 / TForce4 Ultra 7 PnP/PCI Configurations This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. Figure 7.
TForce4 / TForce4 Ultra Resources Controlled By By Choosing “Auto(ESCD)” (default), the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral.By Choosing “Manual”, the user will need to assign IRQ & DMA for add-on cards. Be sure that there are no IRQ/DMA and I/O port conflicts. IRQ Resources This submenu will allow you to assign each system interrupt a type, depending on the type of device using the interrupt.
TForce4 / TForce4 Ultra 8 PC Health Status A、Figure 8. PC Health Status Chassis Open Warning This item allows you to enable or disable Chassis Open Warning beep. The Choices: Disabled (Default), Enabled. Shutdown Te mperature This item allows you to set up the CPU shutdown Temperature. This item only effective under Windows 98 ACPI mode. The Choices: Disabled (default), 60℃/140F, 65℃/149F, 70℃/158F, 75℃/167F. CPU FAN Control by The Choice “smart” can make your CPU FAN to reduce noise.
TForce4 / TForce4 Ultra Current SYS FAN Speed This field displays the current speed SYSTEM fan. B 、 Figure 8. PC Health Status Chassis Open Warning This item allows you to enable or disable Chassis Open Warning beep. The Choices: Disabled (Default), Enabled. Shutdown Te mperature This item allows you to set up the CPU shutdown Temperature. This item only effective under Windows 98 ACPI mode. The Choices: Disabled (default), 60℃/140F, 65℃/149F, 70℃/158F, 75℃/167F.
TForce4 / TForce4 Ultra Start PWM Value The Choices: 32 (default). Slope PWM The Choices: 1 PWM Value/℃ (default), 2 PWM Value/℃, 4 PWM Value/℃, 8 PWM Value/℃,16 PWM Value/℃,32 PWM Value/℃, 64PWM Value/℃. Show H/W Monitor in POST If your computer contains a monitoring system, it will show PC health status during POST stage. The item offers several delay time for you to choose. The Choices: Disabled (default), Enabled. CPU Vcore/ +1.5V+3.3V/ +5.0V/ +12.
TForce4 / TForce4 Ultra 9 Over Clock Navigator Engine Automate Overclock System A.O.S. is designed for beginners in overclock field. Based on many test and experiments from BET, A.O.S.
TForce4 / TForce4 Ultra z V6 Tech Engine: z V8 Tech Engine This setting will raise about 15%~25% of whole system performance.
TForce4 / TForce4 Ultra V12 Tech Engine z This setting will raise about 25%~30% of whole system performance. Cautions: 1. 2. Not all types of AMD CPU perform above overclock setting ideally; the difference will be based on the selected CPU model. From BET experiment, the Atholon64 FX CPU are not suitable for this A.O.S. feature. Manual Overclock System (M.O.S.) MOS is designed for experienced overclock users. It allows users to customize personal overclock setting.
TForce4 / TForce4 Ultra NB/SB Voltage Ragurator The Choices:1.52V(default),1.60V,1.68V,1.76V. Memorry Voltage The Choices:2.60V(default),2.70V,2.80V,2.90V. CPU Frequency This item allows you to select the CPU Frequency. The Choices: 200 (default),201,202,203,204,205,206,207,208,209…..450.( Max.is 450) Hammer CPU Multiplier The Max. value will be different from the selected CPU types. The Choices: StartUp (default),X4 800MHz, X5 1000MHz, X6 1200MHz, X7 1400MHz, X8 1600MHz, X9 1800MHz, etc.
TForce4 / TForce4 Ultra Timing Mode DDR Timing Setting by SPD or ITEM. The Choices: Auto (Default), Manual. CAS# Latency(Tcl) This field specify the cas# latency, i.e. cas# to read data valid. The Choices: CL=2.5(Default), CL=3.0, CL=2.0, Min RAS# active time (Tras) This field specifies the minimum RAS# active time. Typically -45-60 Nsec. The Choices: 8T(Default). RAS# to CAS# Delay (Trcd) This field specifies the RAS# to CAS# Delay to read/ write command to the same bank. Typically -20 Nsec.
TForce4 / TForce4 Ultra Step 2: When the process is done, change the setting back from “Enable” to “Disable” to complete the test.
TForce4 / TForce4 Ultra 10 CMOS Reload Program(C.R.P.) It allows users to save different CMOS settings into BIOS-ROM. Users are able to reload any saved CMOS setting to change system configurations. Moreover, users are able to save ideal overclock setting when under overclock operation. There are 50 sets record addresses in total, and users are able to name the CMOS data according to personal like.