P4M890-M7 SE Setup Manual FCC Information and Copyright This equipment has been tes ted and found to comply with the limits of a Class B digital devic e, purs uant to Part 15 of the FCC Rules . T hese limits are designed to provide reasonable protec tion against harmful interference in a residential installation.
Table of Contents Chapter 1: Introduction ............................................. 3 1.1 1.2 1.3 1.4 1.5 Before You Start................................................................... 3 Package Checklist................................................................ 3 Motherboard Features.......................................................... 4 Rear Panel Connectors.......................................................... 5 Motherboard Layout .................................................
P4M890-M7 SE CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU ST ART Thank you for choosing our product. Be fore you start installing the mothe rboard, please make sure you follow the instructions be low: Prepare a dry and stable work ing environment with sufficie nt lighting. Always disconne ct the compute r from powe r outle t be fore ope ration.
Motherboard Manual 1.3 MOT HERBOARD FEAT URES SPEC LGA 775 Intel Core 2Duo/ Pe ntium 4 / Pe ntium D / Supports Hy per Tra nsport/ Execute Disable CPU Celeron D pr ocessor up to 3.8 GHz Bit/ Enhanced Intel S peedStep®/ Intel *It is recommende d to use processors Extende d Memor y 64 technolo gy with 95W power consumption.
P4M890-M7 SE SPEC Back Panel I/O S/PDIF o ut co nnector x1 CPU Fan hea der x1 Supports di gital a udio out function CPU Fan power s upply (with Smart Fa n function) System Fan hea der x1 System Fan Power supply Clear CMOS header x1 Restore CMOS data to factory defa ult USB connector x2 Power Connector ( 24pi n) x1 Connects to Power supply Power Connector ( 4pin) x1 Connects to Power supply PS/2 Keyboard x1 Connects to PS/ 2 Key board PS/2 Mo use x1 Connects to PS/ 2 Mo use Serial
Motherboard Manual 1.5 MOT HERBOARD LAYOUT JCFAN1 J KBMS 1 LGA775 COM1 JCOM1 CPU1 JPRNT1 DIMM1 JVGA1 JUSB1 DIMM2 JATXPWR1 JUSBV1 IDE1 P4M890 JUSBLAN1 IDE2 JATXPWR2 LAN J AUDIO1 PCI-EX16 Super I/O PCI-EX1_1 BAT1 JSATA2 JUSB2 VIA VT8237A PCI1 BIOS JSATA1 JCDIN1 JUSB3 PCI2 JCMOS1 JSPDIF_OUT1 Codec JAUDIOF1 Not e: ■ represe nts the 1st pin.
P4M890-M7 SE CHAPTER 2: HARDWARE INSTALLATION 2.1 INST ALLING CENT RAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Pin Cap Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a 90-degree angle.
Motherboard Manual Step 2: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 2-1: Step 2-2: Step 3: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the JCFAN1. This completes the installation.
P4M890-M7 SE 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. JCFAN1: CPU Fan Heade r 4 1 JCFAN1 Pin 1 2 3 4 Assignment Ground +12V FAN RPM rate sense Smart Fan Control JSFAN1: System Fan He ader Pin JSFAN1 3 1 2 3 Assignment Ground +12V FAN RPM rate sense 1 Note: The JSFAN1 s upport 3-pi n head connec tor.
Motherboard Manual 2.3 INST ALLING SYST EM MEMORY DIMM1 DIMM2 A. Memory Modules 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated. B.
P4M890-M7 SE 2.4 CONNECT ORS AND SLOT S FDD1: Floppy Disk Conne ctor The motherboard prov ides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk ty pes. This connector supports the prov ided f loppy drive ribbon cables. 2 34 1 33 IDE1/IDE2: Hard Disk Conne ctors The motherboard has a 32-bit Enhanced PCI IDE Controller that prov ides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 f unctionality.
Motherboard Manual PCI-EX16: PCI-Express x16 Slot - PCI-Express 1.0a compliant. - Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, f or an aggregate of 8GB/s totally. PCI-EX1_1: PCI-Express x1 Slot - PCI-Express 1.0a compliant. - Data transf er bandwidth up to 250MB/s per direction; 500MB/s in total. PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins. 2X bandwidth ov er the traditional PCI architecture.
P4M890-M7 SE CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW T O SET UP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DET AIL SETT INGS JPANEL1: Front Panel Heade r This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep button and speaker connection. It allows user to connect the PC case’s f ront panel switch functions.
Motherboard Manual ATX Powe r Source Conne ctor: JATXPWR1 JATXPWR1 allows user to connect 24-pin power connector on the ATX power supply. 12 24 1 13 Pin Assignment Pin Assignment 13 14 15 16 17 18 19 20 21 22 23 24 +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground 1 2 3 4 5 6 7 8 9 10 11 12 +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.
P4M890-M7 SE JUSB2/JUSB3: Heade rs for USB 2.0 Ports at Front Panel This header allows user to connect additional USB cable on the PC f ront panel, and also can be connected with internal USB devices, like USB card reader. 2 10 JUSB2 1 9 JUSB3 Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC JUSBV1/JUSBV2: Powe r Source Heade rs for USB Ports Pin 1-2 Close: JUSBV1: +5V for USB ports at JUSB1/JUSBLAN1.
Motherboard Manual JAUDIO F1: Front Panel Audio Heade r This header allows user to connect the front audio output cable with the PC f ront panel. It will disable the output on back panel audio connectors.
P4M890-M7 SE JCMO S1: Cle ar CMOS Heade r By placing the jumper on pin2-3, it allows user to restore the BIOS saf e setting and the CMOS data, please carefully f ollow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (default). 1 1 3 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Proce dures: 1. 2. 3. 4. 5. 6. Remov e AC power line. Set the jumper to “Pin 2-3 close”. Wait f or f ive seconds. Set the jumper to “Pin 1-2 close”. Power on the AC.
Motherboard Manual CHAPTER 4: USEFUL HELP 4.1 DRIVER INST ALLAT ION NOT E After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you ins ert the Driver CD, please use file brows er to locate and execute the file SETUP.
P4M890-M7 SE 4.2 AWARD BIOS BEEP CODE Beep Sound One long beep followed by two short beeps High-low siren sound Meaning Video card not found or v ideo card memory bad CPU overheated System will shut down automatically One Short beep when system boot-up No error found during POST Long beeps every other second 4.3 No DRAM detected or install EXT RA INFORMAT ION A. BIOS Update After you fail to update BIOS or BIOS is invaded by virus, the Boot-Block function will help to restore BIOS.
Motherboard Manual B. CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed.
P4M890-M7 SE 4.4 TROUBLESHOOT ING Probable Solution 1. Make sure power cable is No power to the system at all securely plugged in. Power light don’t illuminate, f an inside power supply does not turn 2. Replace cable. on. 3. Contact technical support. 2. Indicator light on key board does not turn on. System inoperativ e. Keyboard lights Using even pressure on both ends of are on, power indicator lights are lit, the DIMM, press down firmly until the and hard driv e is spinning. module snaps into place. 1.
Motherboard Manual CHAPTER 5: WARPSPEEDER™ 5.1 INT RODUCT ION [WarpSpeeder™], a new powerful control utility, features three user-friendly functions including Overclock Manager, Overvoltage Manager, and Hardware Monitor. With the Overclock Manager, users can easily adjust the frequency they prefer or they can get the best CPU performance with just one click. The Overvoltage Manager, on the other hand, helps to power up CPU core voltage and Memory voltage.
P4M890-M7 SE 5.3 INST ALLAT ION 1. Execute the setup execution file, and then the following dialog will pop up. Please click “Next” button and follow the default procedure to install. 2. When you see the following dialog in setup procedure, it means setup is completed. If the “Launch the WarpSpeeder Tray Utility” checkbox is checked, the Tray Icon utility and [WarpSpeeder™] utility will be automatically and immediately launched after you click “Finish” button.
Motherboard Manual 5.4 WARPSPEEDER™ 1. Tray Icon: Whenever the Tray Icon utility is launched, it will display a little tray icon on the right side of Windows Taskbar. This utility is responsible for conveniently invoking [WarpSpeeder™] Utility. You can use the mouse by clicking the left button in order to invoke [WarpSpeeder™] directly from the little tray icon or you can right-click the little tray icon to pop up a popup menu as following figure.
P4M890-M7 SE 2. Main Panel If you click the tray icon, [WarpSpeeder™] utility will be invoked. Please refer to the following figure; the utility’s first window you will see is Main Panel. Main Panel contains fe ature s as follows: a. Display the CPU Speed, CPU external clock, Memory clock, AGP clock, and PCI clock information. b. Contains About, Voltage, Overclock, and Hardware Monitor Buttons for invoking respective panels. c.
Motherboard Manual 3. Voltage Panel Click the Voltage button in Main Panel, the button will be highlighted and the Voltage Panel will slide out to up as the following figure. In this panel, you can decide to increase CPU core voltage and Memory voltage or not. The default setting is “No”. If you want to get the best performance of overclocking, we recommend you click the option “Yes”.
P4M890-M7 SE 4. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel will slide out to left as the following figure. O ve rclock Panel contains the these features: a. “–3MHz button”, “-1MHz button”, “+1MHz button”, and “+3MHz button”: provide user the ability to do real-time overclock adjustment. Warning: Manually overclock is potentially dangerous, especially when the ov erclocking percentage is over 110 %.
Motherboard Manual c. d. “Auto-overclock button”: User can click this button and [WarpSpeeder™] will set the best and stable performance and frequency automatically. [WarpSpeeder™] utility will execute a series of testing until system fail. Then system will do fail-safe reboot by using Watchdog function. After reboot, the [WarpSpeeder™] utility will restore to the hardware default setting or load the verified best and stable frequency according to the Recovery Dialog’s setting.
P4M890-M7 SE 6. About Panel Click the “about” button in Main Panel, the button will be highlighted and the About Panel will slide out to up as the following figure. In this panel, you can get model name and detail information in hints of all the chipset that are related to overclocking. You can also get the mainboard’s BIOS model and the Version number of [WarpSpeeder™] utility.
Motherboard Manual APPENDENCIES: SPEC IN OTHER LANGUAGE GERMAN Spezifikationen LGA 775 Intel Core2Duo/ Pe ntium 4 / Pe ntium D Unterstützt Hyper-Threa ding / Execute Disable CPU / Celeron D Prozessoren mit bis zu 3,8 Bit / Enhance d I ntel Spee dStep® / Intel GHz Architecture-64 / Exte nde d Memory 64 *It is recommende d to use processors Technol ogy with 95W power consumption. FSB Chipsatz Grafik Super E/A 533 / 800 / 1066 MHz VIA P4M890 VIA VT8237A Integrierter U niChrome Pro C hipsatz Max.
P4M890-M7 SE Spezifikationen Onboard-An schluss Jeder A nschluss unterstützt 2 Diskettenlaufwerk anschluss x1 IDE-Anschluss x2 Jeder A nschluss unterstützt 2 IDE-L aufwerk e SATA-Anschluss x2 Jeder A nschluss unterstützt 1 SATA-Laufwerk Fronttafela nschluss x1 Unterstützt die Fro nttafelfunktio nen Front-Audioa nschluss x1 CD-IN-Anschluss x1 Unterstützt die CD Audio-I n-Funktion S/PDIF-Ausgangsanschluss x1 Unterstützt die di gitale Audi oausgabe funktion CPU-Lüfter-Sockel x1 System-L
Motherboard Manual FRANCE SPEC LGA 775 Processeurs Intel Core 2Duo/ P entium Prend en charge les technologies UC 4 / Pe ntium D / Celer on D jusqu'à 3,8 Hyper -Thre ading / d'ex écution de bit de désactivation / I ntel Spe edStep® optimisée/ GHz *It is recommende d to use processors d'architecture Intel 64 / de mém oire éte ndue 64 with 95W power consumption.
P4M890-M7 SE SPEC Connecteur SATA x2 Connecteur du pa nne au avant x1 Connecteur Audio du panneau Chaque connecteur prend e n char ge 1 périphéri que SATA Prend en charge les é quipements du panneau avant Prend en charge la fo nction a udio du panneau avantx1 x1 avant Connecteur d'entré e CD x1 Prend en charge l a fonction d'entrée audio de CD Connecteur de sortie S/PDIF x1 Embase de ve ntilateur UC x1 Embase de ve ntilateur système x1 Embase d'e ffacement CMOS x1 Connecteur USB x2 Conne
Motherboard Manual IT ALIAN SPECIFICA LGA 775 Processore Intel Core 2Duo/ Pentium CPU 4 / Pentium D / Celero n D fino a 3.8 GHz *It is recommende d to use processors Supporto di Hyper -Threadi ng / Execute Disable Bit / Enhance d I ntel Spee dStep® / Architettura Intel 64 / Tecnologia Exte nde d Memory 64 with 95W power consumption.
P4M890-M7 SE SPECIFICA Connettore flo ppy x1 Ciascun connettore supporta 2 unità Floppy Connettore IDE x2 Ciascun connettore supporta 2 unità IDE Connettore SATA x2 Ciascun connettore supporta 1 unità SATA Connettore pa nnello fro ntale x1 Supporta i servizi del pa nnell o fr ontale Connettore audio frontale x1 Supporta la funzione audi o pannello frontale Connettore CD-in x1 Supporta la funzione i nput audio C D Connettore output SPDIF x1 Supporta la funzione d’output a udio digitale C
Motherboard Manual SPANISH Especificación LGA 775 CPU Procesador I ntel Core 2Duo/ P entium Admite Hyper -Threadi ng / Bit de deshabilitación 4 / Pentium D / Celero n D hasta 3,8 de ejecució n / Intel SpeedStep® Me jorado / Intel GHz Architecture-64 / Tecnologí a Extended Memor y *It is recommende d to use processors 64 with 95W power consumption.
P4M890-M7 SE Especificación Cada conector soporta 2 uni dades de disco Conector disco flexible X1 Conector IDE X2 Cada conector soporta 2 dispositivos IDE Conector SATA X2 Cada conector soporta 1 dispositivos SATA Conector de pa nel fro ntal X1 Soporta instalaciones en el panel fr ontal Conector de sonido frontal X1 Soporta funcio nes de sonido e n el pa nel frontal Conector de entra da de C D X1 Soporta funció n de e ntrada de sonido de CD Conector de salida S/PDIF Conectore Cabecera de v
Motherboard Manual PORT UGUESE ESPECIFICAÇÕES LGA 775 Processador Intel Cor e2Duo/ Pentium Suporta as tecnologias Hyper -Threa ding / CPU 4 / Pentium D / Celero n D até 3,8 GHz Execute Disable Bit / Enhanced I ntel SpeedStep® *It is recommende d to use processors / Intel Arquitecture - 64 / Extended Memory 64 with 95W power consumption.
P4M890-M7 SE ESPECIFICAÇÕES Conector da unida de de x1 Conector IDE x2 Cada conector suporta 2 dispositivos IDE Conector SATA x2 Cada conector suporta 1 dispositivo SATA Conector do pai nel fro ntal x1 Para suporte de várias funções no painel fro ntal Conector de áudio fro ntal x1 Suporta a função de áudio no painel fr ontal Conector para e ntrada de C Ds x1 Suporta a e ntrada de áudi o a partir de C Ds Conector de saída S/PDIF x1 Conectore Conector da ve ntoinha da CPU s na placa Cada co
Motherboard Manual POLISH SPEC LGA 775 Procesor Intel Core 2Duo/ P entium 4 / Procesor Pentium D / Celeron D do 3,8 GHz *It is recommende d to use processors with 95W power consumption. FSB Chipset Grafika Obsługa Hy per-Thre ading / Execute Disabl e Bit / Enha nced Intel SpeedStep® / I ntel Architecture-64 / Exte nde d Memory 64 Technol ogy 533 / 800 / 1066 MHz VIA P4M890 VIA VT8237A Zintegrowana w chipsecie U niChrome Maks.
P4M890-M7 SE SPEC Złącza Złącze napędu dyskietek x1 Każde złącze obsługuje 2 na pędy dyskietek Złącze IDE x2 Każde złącze obsługuje 2 urządze nia I DE Złącze SATA x2 Każde złącze obsługuje 1 urządze nie SATA Złącze panela przedniego x1 Obsługa eleme ntów pa nela przedniego Przednie złącze a udio x1 Obsługa funkcji audio na pa nelu przednim Złącze wejścia CD x1 Obsługa funkcji wejścia a udio CD Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowe go wy jścia audi o Złącze główkowe wentylat
Motherboard Manual RUSSIAN СПЕЦ. CPU LGA 775 (центра ль Процессор Intel Core 2Duo/ Pe ntium ный 4 / Pentium D / Celero n D до 3.8 ГГц процессор *It is recommende d to use processors ) with 95W power consumption.
P4M890-M7 SE СПЕЦ.
Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت LGA 775 Intel Core2Duo/ Penti um 4 /ﻡﻌﺎﻟﺠﺎت وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﺑ ﺘﺮدد ﻳﺼﻞ إﻟﻰ Pentium D / Celeron D 8.3 اﻟﻤﺮآﺰﻳ ﺔ ﺝﻴﺠﺎ هﺮﺕﺰ *It is recommende d to use processors Hyper -Thr eadi ng / Ex ecute Disa ble Bitﺕﺪﻋﻢ ﺕﻘﻨﻴ ﺎت / Enha nced I ntel Spee dStep® / Exte nde d Memory 64 Technology with 95W power consumption.
P4M890-M7 SE اﻟﻤﻮاﺻﻔﺎت اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ اﻟﻠﻮﺣ ﺔ ﻡﻨﻔﺬ ﻡﺤﺮك أﻗﺮاص ﻡﺮﻥﺔ ﻋﺪد 1 ﻳﺪﻋﻢ ﻡﺤﺮآﻴﻦ ﻟﻸﻗﺮا ص اﻟﻤﺮﻥﺔ ﻡﻨﻔﺬIDE ﻋﺪد 2 IDEﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺝﻬﺰة ﻡﻨﻔﺬSATA ﻋﺪد 2 SATAﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻋﺪد 1 ﻳﺪﻋﻢ ﺕﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮ ت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬCD-IN ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻡ ﺞ ﻡﻨﻔﺬ ﺥﺮجS/PDIF ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤ ﻲ وﺹﻠﺔ
Motherboard Manual JAPANESE 仕様 LGA 775 Intel Core2Duo/ Pe ntium 4 / Pentium CPU D / Celeron D processor up to 3.8 GHz *It is recommende d to use processors with 95W power consumption.
P4M890-M7 SE 仕様 各コネクタは2つのフロッピードライブをサポートし フロッピーコネクタ x1 IDEコネクタ x2 各コネクタは2つのIDEデバイスをサポートします SATAコネクタ x2 各コネクタは1つのSATAデバイスをサポートします フロントパネルコネクタ x1 フロントパネル機能をサポートします フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします CDインコネクタ x1 CDオーディオイン機能をサポートします S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x1 システムファン電源装置 CMOSクリアヘッダ x1 USBコネクタ x2 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 ます オンボード コネクタ 各コネクタは2つのフロントパネルUSBポートをサポ ートします シリアルポート
P4M890-M7 SE BIOS Setup BIOS Setup .................................................................................................1 1 Main Menu...............................................................................................3 2 Standard CMOS Features......................................................................7 3 Advanced BIOS Features .......................................................................9 4 Advanced Chipset Features................................................
P4M890-M7 SE BIOS Setup Introduction The purpose of this manual is to describe the settings in the Phoenix-Award™ BIOS Setup program on this motherboard. The Setup program allows users to modify the basic system configuration and save these settings to CMOS RAM. The power of CMOS RAM is supplied by a battery so that it retains the Setup inform ation when the power is turned off. Basic Input-Output System (BIOS) determines what a computer can do without accessing programs from a disk.
P4M890-M7 SE ACPI Support Phoenix-Award ACPI BIOS support Version 1.0b of Advanced Configuration and Power interface speci fi cation (ACPI). It provides ASL code for power management and devi ce configuration capabilities as defined in the ACPI speci fication, developed by Microsoft, Intel and Toshiba. PCI Bus Support This PHOENIX-AWARD BIOS also supports Version 3.0 of the Int el PCI (Peripheral Component Interconnect) local bus specification.
P4M890-M7 SE 1 Main Menu Once you enter Phoenix-Award BIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions. Use the arrow keys to select among the items and press to accept and enter the sub-menu. !! WARNING !! For better system performance, the BIOS firmware is being continuously updated. The BIOS information described in this manual (Figure 1, 2, 3, 4, 5, 6, 7, 8, 9) is for your reference only.
P4M890-M7 SE Advanced Chipset Features This submenu allows you to configure special chipset features. Integrated Peripherals This submenu allows you to configure cert ain IDE hard drive options and Programmed Input/ Output features. Power Management Setup This submenu allows you to configure the power managem ent features. PnP/PCI Configurations This submenu allows you to configure cert ain “ Plug and Play” and PCI options. PC Health Status This submenu allows you to monitor the hardware of your system.
P4M890-M7 SE Set Supervisor Password Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility. You will be prompted with to enter a password. Set User Password If the Supervisor Password is not set, then the User Password will function in the same way as the Supervisor Password. If the Supervisor Password is set and the User Password is set, the “User” will only be able to view configurations but will not be able to change them.
P4M890-M7 SE Upgrade BIOS This submenu allows you to upgrade bios.
P4M890-M7 SE 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into several categori es. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the or keys to select the value you want in each item. Figure 2: Standard CMOS Setup Main Menu Selections This table shows the items and the available options on the Main Menu. Item Options Description Date mm : dd : yy Set the system date.
P4M890-M7 SE Item Options Description IDE Channel 1 Master Options are in its sub menu. Press to enter the sub menu of detailed options. IDE Channel 1 Slav e Options are in its sub menu. Press to enter the sub menu of detailed options. 360K, 5.25 in 1.2M, 5.25 in Driv e A 720K, 3.5 in Driv e B 1.44M, 3.5 in Select the ty pe of f loppy disk drive installed in your sy stem. 2.88M, 3.
P4M890-M7 SE 3 Advanced BIOS Features Figure 3: Advanced BIOS Setup Boot Seq & Floppy Setup This item allows you to setup boot sequence & Floppy.
P4M890-M7 SE Hard Disk Boot Priority The BIOS will attempt to arrange the Hard Disk boot sequence automatically. You can change the Hard Disk booting sequence here. The Choices: Pri. Master, Pri. Slave, Sec. Master, Sec. Slave, USB HDD0, USB HDD1, USB HDD2, and Bootable Add-in Cards. First/Second/Third Boot Dev ice The BIOS will attempt to load the operating system in this order. The Choices: Floppy, LS120, Hard Disk, CDROM, ZIP 100, USB-FDD, USB-ZIP , USB-CDROM, LAN, Disabled.
P4M890-M7 SE Boot Up Floppy Seek When enabled, System will test the floppy drives to determine if they have 40 or 80 tracks during boot up. Disabling this option reduces the time it takes to boot-up. The Choices: Enabled (default), Disabled. Shadow Setup This item allows you to setup cache & shadow setup. Figure 3.2: Shadow Setup Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution or not. Enabled (default) Optional ROM is enabled.
P4M890-M7 SE Cache Setup CPU L1 & L2 Cache Depending on the CP U/chipset in use, you may be able to increase me mory access time with this option. Enabled (default) Enable cache. Disabled Disable cache. CPU L3 Cache Depending on the CP U/chipset in use, you may be able to increase me mory access time with this option. Enabled (default) Enable cache. Disabled Disable cache. CPU L2 Cache ECC Checking This item allows you to enable/disable CPU L2 Cache ECC Checking.
P4M890-M7 SE CPU Feature Delay Prior to Thermal Set this item to enable the CP U Thermal function to engage after the specified time. The Choices: 4 Min, 8 Min, 16Min (default), 32 Min. Thermal Management This option allows you to select the way to control the “ Thermal Management.” The Choices: Thermal Monitor 1 (default), Thermal Monitor 2.
P4M890-M7 SE Limit CPUID MaxVal Set Limit CP UID MaxVal to 3, it should be “ Disabled” for Windows XP . The Choices: Disabled (default), Enabled. C1E Function This item allows you to configure the Enhanced Halt State (C1E) function, which may reduce the power consumption of your system when the system is idle. The Choices: Auto (default),Disabled. Execute Disable Bit This item allows you to configure the Execute Disabled Bit function, which protects your system from buffer overflow attacks.
P4M890-M7 SE Quick Power On Self Test Enabling this option will cause an abridged version of the Power On Self-Test (POST) to execute after you power up the computer. Disabled Normal POST. Enabled (default) Enable quick POST. Boot Up NumLock Status Selects the NumLock State after the system switched on. The Choices: On (default) Numpad is number keys. Off Numpad is arrow keys. Typematic Rate Setting When a key is held down, the keystroke will repeat at a rate determined by the keyboard controller.
P4M890-M7 SE MPS Version Control For OS The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor speci fication. Select version supported by the operation system running on this computer. The Choices: 1.4 (default), 1.1. OS Select For DRAM > 64MB A choice other than Non-OS2 is only used for OS2 systems with memory exceeding 64MB. The Choices: Non-OS2 (default), OS2. HDD S.M.A.R.T. Capability This item allows you to enable/disable HDD S.M.A.R.T. Capability.
P4M890-M7 SE 4 Advanced Chipset Features This submenu allows you to configure the speci fic features of the chipset installed on your system. This chipset manage bus speeds and access to system memory resources, such as DRAM. It also coordinates communications with the PCI bus. The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly.
P4M890-M7 SE AGP & P2P Bridge Control Highlight “Press Enter” next to the “ AGP & P2P Bridge Control” label and pressing the enter key will take you a submenu with the following options: Figure 4.1: AGP & P2P Bridge Control AGP Aperture Size Select the size of the Accelerated Graphics Port (AGP ) aperture. The aperture is a portion of the P CI memory address range dedicated for graphics memory address space.
P4M890-M7 SE AGP Master 1 WS Read When enabled, read to the AGP (Accelerated Graphics P ort) are executed with one wait states. The Choices: Enabled (default), Disabled. VGA Share Memory Size This item allows you to select the VGA share memory size. The Choices: 64M (default), 16M, 32M, 128M, 256M, Disabled Direct Frame Buffer This item allows you to disabled or enabled direct frame buffer The Choices: Enabled (default), Disabled.
P4M890-M7 SE PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with P CI specification. The Choices: Enabled (default), Disabled. Vlink mode selection This item allows you to select Vlink mode. The Choices: B y Auto (default), Mode 0 , Mode 1. VLink 8X Support This item allows you to enable or disable VLink 8X support. The Choices: Enabled (default), Disabled.
P4M890-M7 SE 5 Integrated Peripherals Figure 5.
P4M890-M7 SE SATA Controller This option allows you to enable the on-chip Serial ATA. The Choices: Enabled (default), Disabled. SATA Controller Mode This option allows you to select SATA Mode. The Choices: RAID, IDE (default). IDE DMA Transfer Access This item allows you to enable or disable the IDE DMA transfer access. The Choices: Enabled (default), Disabled. On-chip IDE Channel 0/1 The motherboard chipset contains a P CI IDE interface with support for two IDE channels.
P4M890-M7 SE Primary/Secondary/Master/Slave UDMA Ultra DMA function can be implemented if it is supported by the IDE hard drives in your system. As well, your operating environment requires a DMA driver (Windows 95 or OSR2may need a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA, select Auto to enable BIOS support. The Choices: Auto (default), Disabled.
P4M890-M7 SE LAN Controller This option allows you to control the onboard LAN. The Choices: Enabled (default), Disabled Lan Boot ROM Decide whether to invoke the boot ROM of the onboard LAN chip. The Choices: Disable (default), Enabled. Super IO Device Press Enter to configure the Super I/O Device. Onboard FDC Controller Select enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it.
P4M890-M7 SE Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O Address. The Choices: 378/IRQ 7 (default), 278/IRQ5, 3BC/IRQ7, Disabled. Parallel Port Mode This item allows you to determine how the parallel port should function. The default value is SPP . The Choices: SPP (de fault) Using P arallel port as Standard P rinter Port. EPP Using P arallel P ort as Enhanced P arallel Port. ECP Using P arallel port as Extended Capabilities P ort.
P4M890-M7 SE USB 1.0/2.0 Controller These options allow you to enable or disable the USB 1.0/2.0 controller function. The Choices: Enabled (default), Disabled. USB Operation Mode This option let you select the operation mode of USB function. The Choices: High Speed (default), Full/Low Speed. USB Keyboard/Mouse/Storage Function These options allow you to enable or disable the USB keyboard/mouse/storage devices. The Choices: Enabled (default), Disabled.
P4M890-M7 SE 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features. Figure 6. Power Management Setup ACPI Function This item displays the status of the Advanced Configuration and Power Management (ACPI). The Choices: Enabled (default), Disabled.
P4M890-M7 SE Power Management This category allows you to select the power saving method and is directly related to the following modes: 1. HDD Power Down. 2. Suspend Mode. There are three options of Power Management, three of which have fixed mode settings Min. Power Saving Minimum power management. Suspend Mode = 1 hr. HDD Power Down = 15 min Max. Power Saving Maximum power management only available for sl CPU’s. Suspend Mode = 1 min. HDD Power Down = 1 min.
P4M890-M7 SE Video Off Method This option determines the manner when the monitor goes blank. V/H SYNC+Blank (default) This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer. Blank Screen This option only writes blanks to the video buffer. DPMS Initial display power management signaling. Modem Use IRQ This determines the IRQ, which can be applied in MODEM use. The Choices: 3 (default), 4, 5, 7, 9, 10, 11, NA.
P4M890-M7 SE WDRT Support This option allows you to disabled or enables the Watchdog Timer. The Choices: Enabled (default), Disabled. WDRT Run/Stop This option allows you to select the mode of Watchdog Timer. The Choices: Stop (default), Run. WDRT Count This option allows you to control the count of the Watchdog Timer. The Choices: 1023 (default); min=0, amx=1023, key in a DEC number. Wakeup Event Detect Figure 6.
P4M890-M7 SE PowerOn by PCI Card When you select Enabled, a P ME signal from P CI card returns the system to Full ON state. For this function to work, you may need a LAN add-on card which supports the Wake on LAN function. Set the Wake on LAN (WOL) jumper on motherboard to enable if applicable. The Choices: Disabled (default), Enabled. Modem Ring Resume This item allows you to disable or enable Modem Ring Resume function. The Choices: Disabled (default), Enabled.
P4M890-M7 SE 7 PnP/PCI Configurations This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components. This section covers some very techni cal items and it is strongly recommended that only experienced users should make any changes to the default settings.
P4M890-M7 SE Reset Configuration Data The system BIOS supports the PnP feature which requires the system to record which resources are assigned and protects resources from conflict. Every peripheral device has a node, which is called ESCD. This node records which resources are assigned to it. The system needs to record and update ESCD to the memory locations. These locations are reserved in the system BIOS.
P4M890-M7 SE IRQ Resources This submenu will allow you to assign each system interrupt a type, depending on the type of device using the interrupt. When you press the “ Press Enter” tag, you will be directed to a submenu that will allow you to configure the system interrupts. This is only configurable when “ Resources Controlled By” is set to “Manual”.
P4M890-M7 SE 8 PC Health Status Figure 8: PC Health Status Shutdown Temperature This item allows you to set up the CPU shutdown Temperature. This item is only effective under Windows 98 ACPI mode. The Choices: 65℃/ 149℉, 70℃/ 158℉, 75℃/ 167℉, 80℃/ 176℉, 85℃/ 185 ℉, 90℃/ 167℉, 95℃/ 194℉(default), Disabled. CPU FAN Control by Choose “ smart” to reduce the noise caused by CPU FAN. The Choices: Smart, Always On (default). CPU Fan Load (Sharp=0) The Choices: Min=0, Max=7; key in a DEC number.
P4M890-M7 SE CPU Fan Full speed <℃> When CPU temperature is reach the set value, the CPU fan will work under Full Speed. The Choices: Min=0, Max=100; key in a DEC number. Start PWM Value (%) When CPU temperature arrives to the set value, the CPU fan will work under Smart Fan Function mode. The range is from 0~127, with an interval of 1. The Choices: Min=0, Max=100; key in a DEC number. Slope PWM Level (%/℃) Increasing the value of slope PWM will raise the speed of CPU fan. The Choices: 3.
P4M890-M7 SE 9 Performance Booster Zone Figure 9: Performance Booster Zone DRAM Clock/Drive Control This item controls the DRAM Clock. Highlight “Press Enter” next to the “ DRAM Clock/Drive Control” label and pressing the enter key will take you a submenu with the following options: Figure 9.
P4M890-M7 SE DRAM Clock This item determines DRAM clock. The Choices: B y SPD (default), 100MHz, 133MHz, 166MHz, 200MHz, 266MHz, 333MHz . DRAM Timing This item determines DRAM clock/ timing. The Choices: Auto by SPD (default), Manual, Turbo, Ultra. SDRAM CAS Latency When DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The Choices: 2.5 /4(default). Bank Interleave This item allows you to enable or disable the bank interleave feature.
P4M890-M7 SE ACT (0) to ACT (1) (tRRD) This item allows you to determine the selection for ACT (0) to ACT (1) (tRRD) The Choices: 3T (default). 1T CMD Support The Choices: Disable (default), Auto. DDR2 On Die Termination This option allows you to choose the working type of ODT. The Choices: ODT Always ON (default), Dynamic ODT, ODT Always OFF. CPU CLOCK This item allows you to select CPU Clock, and CPU over clocking.
P4M890-M7 SE Spread Spectrum This item allows you to enable/disable the Spread Spectrum function. The Choices:+/- 0.25% (default), +/- 0. 5%, Disabled, -0.5%, -1.0%. DDR Voltage This item allows you to select DDR Voltage. The Choices: StartUp (default), +0.10V, +0.20V, +0.30V, +0.40V, +0.50V, +0.60V, +0.70V. CPU Voltage This item allows you to select CPU Voltage. The Choices: StartUp (default), +0.012V~+0.787V.
P4M890-M7 SE BIOS Setup BIOS Setup .................................................................................................1 1 Main Menu...............................................................................................3 2 Standard CMOS Features......................................................................7 3 Advanced BIOS Features .......................................................................9 4 Advanced Chipset Features................................................
P4M890-M7 SE BIOS Setup Introduction The purpose of this manual is to describe the settings in the Phoenix-Award™ BIOS Setup program on this motherboard. The Setup program allows users to modify the basic system configuration and save these settings to CMOS RAM. The power of CMOS RAM is supplied by a battery so that it retains the Setup inform ation when the power is turned off. Basic Input-Output System (BIOS) determines what a computer can do without accessing programs from a disk.
P4M890-M7 SE ACPI Support Phoenix-Award ACPI BIOS support Version 1.0b of Advanced Configuration and Power interface speci fi cation (ACPI). It provides ASL code for power management and devi ce configuration capabilities as defined in the ACPI speci fication, developed by Microsoft, Intel and Toshiba. PCI Bus Support This PHOENIX-AWARD BIOS also supports Version 3.0 of the Int el PCI (Peripheral Component Interconnect) local bus specification.
P4M890-M7 SE 1 Main Menu Once you enter Phoenix-Award BIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions. Use the arrow keys to select among the items and press to accept and enter the sub-menu. !! WARNING !! For better system performance, the BIOS firmware is being continuously updated. The BIOS information described in this manual (Figure 1, 2, 3, 4, 5, 6, 7, 8, 9) is for your reference only.
P4M890-M7 SE Advanced Chipset Features This submenu allows you to configure special chipset features. Integrated Peripherals This submenu allows you to configure cert ain IDE hard drive options and Programmed Input/ Output features. Power Management Setup This submenu allows you to configure the power managem ent features. PnP/PCI Configurations This submenu allows you to configure cert ain “ Plug and Play” and PCI options. PC Health Status This submenu allows you to monitor the hardware of your system.
P4M890-M7 SE Set Supervisor Password Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility. You will be prompted with to enter a password. Set User Password If the Supervisor Password is not set, then the User Password will function in the same way as the Supervisor Password. If the Supervisor Password is set and the User Password is set, the “User” will only be able to view configurations but will not be able to change them.
P4M890-M7 SE Upgrade BIOS This submenu allows you to upgrade bios.
P4M890-M7 SE 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into several categori es. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the or keys to select the value you want in each item. Figure 2: Standard CMOS Setup Main Menu Selections This table shows the items and the available options on the Main Menu. Item Options Description Date mm : dd : yy Set the system date.
P4M890-M7 SE Item Options Description IDE Channel 1 Master Options are in its sub menu. Press to enter the sub menu of detailed options. IDE Channel 1 Slav e Options are in its sub menu. Press to enter the sub menu of detailed options. 360K, 5.25 in 1.2M, 5.25 in Driv e A 720K, 3.5 in Driv e B 1.44M, 3.5 in Select the ty pe of f loppy disk drive installed in your sy stem. 2.88M, 3.
P4M890-M7 SE 3 Advanced BIOS Features Figure 3: Advanced BIOS Setup Boot Seq & Floppy Setup This item allows you to setup boot sequence & Floppy.
P4M890-M7 SE Hard Disk Boot Priority The BIOS will attempt to arrange the Hard Disk boot sequence automatically. You can change the Hard Disk booting sequence here. The Choices: Pri. Master, Pri. Slave, Sec. Master, Sec. Slave, USB HDD0, USB HDD1, USB HDD2, and Bootable Add-in Cards. First/Second/Third Boot Dev ice The BIOS will attempt to load the operating system in this order. The Choices: Floppy, LS120, Hard Disk, CDROM, ZIP 100, USB-FDD, USB-ZIP , USB-CDROM, LAN, Disabled.
P4M890-M7 SE Boot Up Floppy Seek When enabled, System will test the floppy drives to determine if they have 40 or 80 tracks during boot up. Disabling this option reduces the time it takes to boot-up. The Choices: Enabled (default), Disabled. Shadow Setup This item allows you to setup cache & shadow setup. Figure 3.2: Shadow Setup Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution or not. Enabled (default) Optional ROM is enabled.
P4M890-M7 SE Cache Setup CPU L1 & L2 Cache Depending on the CP U/chipset in use, you may be able to increase me mory access time with this option. Enabled (default) Enable cache. Disabled Disable cache. CPU L3 Cache Depending on the CP U/chipset in use, you may be able to increase me mory access time with this option. Enabled (default) Enable cache. Disabled Disable cache. CPU L2 Cache ECC Checking This item allows you to enable/disable CPU L2 Cache ECC Checking.
P4M890-M7 SE CPU Feature Delay Prior to Thermal Set this item to enable the CP U Thermal function to engage after the specified time. The Choices: 4 Min, 8 Min, 16Min (default), 32 Min. Thermal Management This option allows you to select the way to control the “ Thermal Management.” The Choices: Thermal Monitor 1 (default), Thermal Monitor 2.
P4M890-M7 SE Limit CPUID MaxVal Set Limit CP UID MaxVal to 3, it should be “ Disabled” for Windows XP . The Choices: Disabled (default), Enabled. C1E Function This item allows you to configure the Enhanced Halt State (C1E) function, which may reduce the power consumption of your system when the system is idle. The Choices: Auto (default),Disabled. Execute Disable Bit This item allows you to configure the Execute Disabled Bit function, which protects your system from buffer overflow attacks.
P4M890-M7 SE Quick Power On Self Test Enabling this option will cause an abridged version of the Power On Self-Test (POST) to execute after you power up the computer. Disabled Normal POST. Enabled (default) Enable quick POST. Boot Up NumLock Status Selects the NumLock State after the system switched on. The Choices: On (default) Numpad is number keys. Off Numpad is arrow keys. Typematic Rate Setting When a key is held down, the keystroke will repeat at a rate determined by the keyboard controller.
P4M890-M7 SE MPS Version Control For OS The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor speci fication. Select version supported by the operation system running on this computer. The Choices: 1.4 (default), 1.1. OS Select For DRAM > 64MB A choice other than Non-OS2 is only used for OS2 systems with memory exceeding 64MB. The Choices: Non-OS2 (default), OS2. HDD S.M.A.R.T. Capability This item allows you to enable/disable HDD S.M.A.R.T. Capability.
P4M890-M7 SE 4 Advanced Chipset Features This submenu allows you to configure the speci fic features of the chipset installed on your system. This chipset manage bus speeds and access to system memory resources, such as DRAM. It also coordinates communications with the PCI bus. The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly.
P4M890-M7 SE AGP & P2P Bridge Control Highlight “Press Enter” next to the “ AGP & P2P Bridge Control” label and pressing the enter key will take you a submenu with the following options: Figure 4.1: AGP & P2P Bridge Control AGP Aperture Size Select the size of the Accelerated Graphics Port (AGP ) aperture. The aperture is a portion of the P CI memory address range dedicated for graphics memory address space.
P4M890-M7 SE AGP Master 1 WS Read When enabled, read to the AGP (Accelerated Graphics P ort) are executed with one wait states. The Choices: Enabled (default), Disabled. VGA Share Memory Size This item allows you to select the VGA share memory size. The Choices: 64M (default), 16M, 32M, 128M, 256M, Disabled Direct Frame Buffer This item allows you to disabled or enabled direct frame buffer The Choices: Enabled (default), Disabled.
P4M890-M7 SE PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with P CI specification. The Choices: Enabled (default), Disabled. Vlink mode selection This item allows you to select Vlink mode. The Choices: B y Auto (default), Mode 0 , Mode 1. VLink 8X Support This item allows you to enable or disable VLink 8X support. The Choices: Enabled (default), Disabled.
P4M890-M7 SE 5 Integrated Peripherals Figure 5.
P4M890-M7 SE SATA Controller This option allows you to enable the on-chip Serial ATA. The Choices: Enabled (default), Disabled. SATA Controller Mode This option allows you to select SATA Mode. The Choices: RAID, IDE (default). IDE DMA Transfer Access This item allows you to enable or disable the IDE DMA transfer access. The Choices: Enabled (default), Disabled. On-chip IDE Channel 0/1 The motherboard chipset contains a P CI IDE interface with support for two IDE channels.
P4M890-M7 SE Primary/Secondary/Master/Slave UDMA Ultra DMA function can be implemented if it is supported by the IDE hard drives in your system. As well, your operating environment requires a DMA driver (Windows 95 or OSR2may need a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA, select Auto to enable BIOS support. The Choices: Auto (default), Disabled.
P4M890-M7 SE LAN Controller This option allows you to control the onboard LAN. The Choices: Enabled (default), Disabled Lan Boot ROM Decide whether to invoke the boot ROM of the onboard LAN chip. The Choices: Disable (default), Enabled. Super IO Device Press Enter to configure the Super I/O Device. Onboard FDC Controller Select enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it.
P4M890-M7 SE Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O Address. The Choices: 378/IRQ 7 (default), 278/IRQ5, 3BC/IRQ7, Disabled. Parallel Port Mode This item allows you to determine how the parallel port should function. The default value is SPP . The Choices: SPP (de fault) Using P arallel port as Standard P rinter Port. EPP Using P arallel P ort as Enhanced P arallel Port. ECP Using P arallel port as Extended Capabilities P ort.
P4M890-M7 SE USB 1.0/2.0 Controller These options allow you to enable or disable the USB 1.0/2.0 controller function. The Choices: Enabled (default), Disabled. USB Operation Mode This option let you select the operation mode of USB function. The Choices: High Speed (default), Full/Low Speed. USB Keyboard/Mouse/Storage Function These options allow you to enable or disable the USB keyboard/mouse/storage devices. The Choices: Enabled (default), Disabled.
P4M890-M7 SE 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features. Figure 6. Power Management Setup ACPI Function This item displays the status of the Advanced Configuration and Power Management (ACPI). The Choices: Enabled (default), Disabled.
P4M890-M7 SE Power Management This category allows you to select the power saving method and is directly related to the following modes: 1. HDD Power Down. 2. Suspend Mode. There are three options of Power Management, three of which have fixed mode settings Min. Power Saving Minimum power management. Suspend Mode = 1 hr. HDD Power Down = 15 min Max. Power Saving Maximum power management only available for sl CPU’s. Suspend Mode = 1 min. HDD Power Down = 1 min.
P4M890-M7 SE Video Off Method This option determines the manner when the monitor goes blank. V/H SYNC+Blank (default) This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer. Blank Screen This option only writes blanks to the video buffer. DPMS Initial display power management signaling. Modem Use IRQ This determines the IRQ, which can be applied in MODEM use. The Choices: 3 (default), 4, 5, 7, 9, 10, 11, NA.
P4M890-M7 SE WDRT Support This option allows you to disabled or enables the Watchdog Timer. The Choices: Enabled (default), Disabled. WDRT Run/Stop This option allows you to select the mode of Watchdog Timer. The Choices: Stop (default), Run. WDRT Count This option allows you to control the count of the Watchdog Timer. The Choices: 1023 (default); min=0, amx=1023, key in a DEC number. Wakeup Event Detect Figure 6.
P4M890-M7 SE PowerOn by PCI Card When you select Enabled, a P ME signal from P CI card returns the system to Full ON state. For this function to work, you may need a LAN add-on card which supports the Wake on LAN function. Set the Wake on LAN (WOL) jumper on motherboard to enable if applicable. The Choices: Disabled (default), Enabled. Modem Ring Resume This item allows you to disable or enable Modem Ring Resume function. The Choices: Disabled (default), Enabled.
P4M890-M7 SE 7 PnP/PCI Configurations This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components. This section covers some very techni cal items and it is strongly recommended that only experienced users should make any changes to the default settings.
P4M890-M7 SE Reset Configuration Data The system BIOS supports the PnP feature which requires the system to record which resources are assigned and protects resources from conflict. Every peripheral device has a node, which is called ESCD. This node records which resources are assigned to it. The system needs to record and update ESCD to the memory locations. These locations are reserved in the system BIOS.
P4M890-M7 SE IRQ Resources This submenu will allow you to assign each system interrupt a type, depending on the type of device using the interrupt. When you press the “ Press Enter” tag, you will be directed to a submenu that will allow you to configure the system interrupts. This is only configurable when “ Resources Controlled By” is set to “Manual”.
P4M890-M7 SE 8 PC Health Status Figure 8: PC Health Status Shutdown Temperature This item allows you to set up the CPU shutdown Temperature. This item is only effective under Windows 98 ACPI mode. The Choices: 65℃/ 149℉, 70℃/ 158℉, 75℃/ 167℉, 80℃/ 176℉, 85℃/ 185 ℉, 90℃/ 167℉, 95℃/ 194℉(default), Disabled. CPU FAN Control by Choose “ smart” to reduce the noise caused by CPU FAN. The Choices: Smart, Always On (default). CPU Fan Load (Sharp=0) The Choices: Min=0, Max=7; key in a DEC number.
P4M890-M7 SE CPU Fan Full speed <℃> When CPU temperature is reach the set value, the CPU fan will work under Full Speed. The Choices: Min=0, Max=100; key in a DEC number. Start PWM Value (%) When CPU temperature arrives to the set value, the CPU fan will work under Smart Fan Function mode. The range is from 0~127, with an interval of 1. The Choices: Min=0, Max=100; key in a DEC number. Slope PWM Level (%/℃) Increasing the value of slope PWM will raise the speed of CPU fan. The Choices: 3.
P4M890-M7 SE 9 Performance Booster Zone Figure 9: Performance Booster Zone DRAM Clock/Drive Control This item controls the DRAM Clock. Highlight “Press Enter” next to the “ DRAM Clock/Drive Control” label and pressing the enter key will take you a submenu with the following options: Figure 9.
P4M890-M7 SE DRAM Clock This item determines DRAM clock. The Choices: B y SPD (default), 100MHz, 133MHz, 166MHz, 200MHz, 266MHz, 333MHz . DRAM Timing This item determines DRAM clock/ timing. The Choices: Auto by SPD (default), Manual, Turbo, Ultra. SDRAM CAS Latency When DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The Choices: 2.5 /4(default). Bank Interleave This item allows you to enable or disable the bank interleave feature.
P4M890-M7 SE ACT (0) to ACT (1) (tRRD) This item allows you to determine the selection for ACT (0) to ACT (1) (tRRD) The Choices: 3T (default). 1T CMD Support The Choices: Disable (default), Auto. DDR2 On Die Termination This option allows you to choose the working type of ODT. The Choices: ODT Always ON (default), Dynamic ODT, ODT Always OFF. CPU CLOCK This item allows you to select CPU Clock, and CPU over clocking.
P4M890-M7 SE Spread Spectrum This item allows you to enable/disable the Spread Spectrum function. The Choices:+/- 0.25% (default), +/- 0. 5%, Disabled, -0.5%, -1.0%. DDR Voltage This item allows you to select DDR Voltage. The Choices: StartUp (default), +0.10V, +0.20V, +0.30V, +0.40V, +0.50V, +0.60V, +0.70V. CPU Voltage This item allows you to select CPU Voltage. The Choices: StartUp (default), +0.012V~+0.787V.