MCP6P M2+ Setup Manual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Chapter 1: Introduction ............................................................ 3 1.1 Before You Start ................................................................................ 3 1.2 Package Checklist ............................................................................. 3 1.3 Motherboard Features...................................................................... 4 1.4 1.5 Rear Panel Connectors .....................................................................
MCP6P M2+ CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: 1.2 Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation.
Motherboard Manual 1.3 MOTHERBOARD FEATURES SPEC Socket AM2+ CPU AMD Phenom / Athlon 64 / Athlon 64 FX / AMD 64 Architecture enables 32 and 64 bit computing Athlon 64 x2 / Sempron processors Supports Hyper Transport and Cool=n=Quiet (Maximum Watt: 95W) FSB Chipset Supports up to 1 GHz Bandwidth Support HyperTransport GeForce 6150 SE/nForce 430 ITE 8716F Super I/O Environment Control initiatives, Provides the most commonly used legacy H/W Monitor Super I/O functionality.
MCP6P M2+ SPEC CD-in Connector Back Panel I/O Board Size Special Features x1 Supports CD audio-in function S/PDIF out Connector x1 Supports digital audio out function CPU Fan Header x1 CPU Fan power supply (with Smart Fan function) System Fan Header x1 System Fan Power supply CMOS clear Header x1 Restore CMOS data to factory default USB Connector x3 Each connector supports 2 front panel USB ports Power Connector (24pin) x1 Connects to Power supply Power Connector (4pin) x1 Connects
Motherboard Manual 1.5 MOTHERBOARD LAYOUT JKBMS1 JCFAN1 JATX PWR4 JUSBPWR1 AM2+ DIMMB1 Socket JVGA1 DIMMA1 JCOM1 JKB_PWR JUSB1 IDE1 JATX PWR1 JUSBPWR2 JUSBLAN1 JAUDIO1 GeForce 6150 SE / nForce 430 JCDIN1 JUSB3 JAUDIOF1 JUSB2 JUSB4 LAN PCI-EX16 BIOS JCMOS1 BAT1 PCI2 Codec JSPDI F_OUT1 Super I/O PCI1 SATA4 SATA1 SATA3 JSFAN1 JPRNT1 FDD1 Note: ■ represents the 1st pin.
MCP6P M2+ CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Step 1: Remove the socket protection cap. Step 2: Pull the lever toward direction A from the socket and then raise the lever up to a 90-degree angle. Step 3: Look for the white triangle on socket, and the gold triangle on CPU should point towards this white triangle. The CPU will fit only in the correct orientation.
Motherboard Manual Step 4: Hold the CPU down firmly, and then close the lever toward direct B to complete the installation. Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN power cable to the JCFAN1. This completes the installation. Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU transition, you may encounter the situation that the new system failed to boot while using new AM2+ CPUs.
MCP6P M2+ 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. JCFAN1: CPU Fan Header 1 4 Pin Assignment Ground +12V FAN RPM rate sense Smart Fan Control (By Fan) 1 2 3 4 JSFAN1: System Fan Header Pin 1 2 3 1 Assignment Ground +12V FAN RPM rate sense 3 Note: The JCFAN1 supports 4-pin head connector.
Motherboard Manual 2.3 INSTALLING SYSTEM MEMORY DIMMA1 DIMMB1 A. Memory Modules 10 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
MCP6P M2+ B. Memory Capacity DIMM Socket Location DDR2 Module Total Memory Size DIMMA1 256MB/512MB/1GB/2GB/4GB DIMMB1 256MB/512MB/1GB/2GB/4GB Max is 8GB. C. Dual Channel Memory installation To trigger the Dual Channel function of the motherboard, the memory module must meet the following requirements: Install memory module of the same density in pair, shown in the following table.
Motherboard Manual 2.4 CONNECTORS AND SLOTS FDD1: Floppy Disk Connector The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables. 2 34 1 33 IDE1: IDE/ATAPI Connector The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
MCP6P M2+ PCI-EX16: PCI-Express x16 Slot - PCI-Express 1.0a compliant. Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally. PCI-Express supports a raw bit-rate of 2.5GB/s on the data pins. 2X bandwidth over the traditional PCI architecture. PCI-EX16 PCI1~PCI2: Peripheral Component Interconnect Slots This motherboard is equipped with 2 standard PCI slots.
Motherboard Manual CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DETAIL SETTINGS JPANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.
MCP6P M2+ JATXPWR1: ATX Power Source Connector This connector allows user to connect 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 1 24 12 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.3V JATXPWR4: ATX Power Source Connector By connecting this connector, it will provide +12V to CPU power circuit.
Motherboard Manual JUSB2/JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel This header allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. Pin 1 2 3 4 5 6 7 8 9 10 JUSB3 JUSB2 JUSB4 2 10 1 9 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC SATA1~SATA4: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 4 channels SATA interface.
MCP6P M2+ JAUDIOF1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable.
Motherboard Manual JSPDIF_OUT1: Digital Audio-out Connector This connector allows user to connect the PCI bracket SPDIF output header. Pin 1 2 3 1 Assignment +5V SPDIF_OUT Ground 3 JCMOS1: Clear CMOS Header By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (default). 1 1 3 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Procedures: 1. 2.
MCP6P M2+ JPRNT1: Printer Port Connector This header allows you to connector printer on the PC.
Motherboard Manual JUSBPWR1/JUSBPWR2: Power Source Headers for USB Ports Pin 1-2 Close: JUSBPWR1: +5V for USB ports at JUSB1/JUSBLAN1. JUSBPWR2: +5V for USB ports at front panel (JUSB2/JUSB3/JUSB4). Pin 2-3 Close: JUSBPWR1: +5V STB for USB ports at JUSB1/JUSBLAN1. JUSBPWR2: +5V STB for USB ports at front panel (JUSB2/JUSB3/JUSB4).
MCP6P M2+ CHAPTER 4: RAID FUNCTIONS 4.1 OPERATION SYSTEM Supports Windows XP and Windows Vista. 4.2 RAID ARRAYS RAID supports the following types of RAID arrays: RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications. RAID 1: RAID 1 defines techniques for mirroring data. RAID 0+1: RAID 0+1 combines the techniques used in RAID 0 and RAID 1. RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity. 4.
Motherboard Manual RAID 1: Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure.
MCP6P M2+ RAID 0+1: RAID 0 drives can be mirrored using RAID 1 techniques. Resulting in a RAID 0+1 solution for improved performance plus resiliency. Features and Benefits Drives: Minimum 4, and maximum is 6 or 8, depending on the platform. Benefits: Optimizes for both fault tolerance and performance, allowing for automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks.
Motherboard Manual RAID 5: RAID 5 stripes both data and parity information across three or more drives. It writes data and parity blocks across all the drives in the array. Fault tolerance is maintained by ensuring that the parity information for any given block of data is placed on a different drive from those used to store the data itself. Features and Benefits Drives: Minimum 3. Uses: RAID 5 is recommended for transaction processing and general purpose service.
MCP6P M2+ CHAPTER 5: USEFUL HELP 5.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.
Motherboard Manual 5.2 SOFTWARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. BIOScreen Utility This utility allows you to personalize your boot logo easily. You can choose JPG or BMP as your boot logo so as to customize your computer.
MCP6P M2+ 5.3 AWARD BIOS BEEP CODE Beep Sound Meaning One long beep followed by two short beeps Video card not found or video card memory bad High-low siren sound CPU overheated System will shut down automatically One Short beep when system boot-up Long beeps every other second No error found during POST No DRAM detected or install 5.
Motherboard Manual 5.5 TROUBLESHOOTING Probable 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. Solution 1. 2. 3. Make sure power cable is securely plugged in. Replace cable. Contact technical support.
MCP6P M2+ This page is intentionally left blank.
Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen Sockel AM2+ CPU AMD Phenom / Athlon 64 / Athlon 64 FX / Athlon 64 x2 / Sempron Prozessoren (Maximales Watt: 95W) FSB Chipsatz 64-Bit-Datenverarbeitung Unterstützt Hyper Transport und Cool’n’Quiet Unterstützt HyperTransport mit einer Bandbreite von bis zu 1 GHz GeForce 6150 SE/nForce 430 ITE 8716F Super E/A Die AMD 64-Architektur unterstützt eine 32-Bit- und Umgebungskontrolle, Bietet die häufig verwendeten alten Super Hardw
MCP6P M2+ Spezifikationen Rückseiten-E /A Platinengröße .
Motherboard Manual FRANCE SPEC Socket AM2+ UC Processeurs AMD Phenom / Athlon 64 / L'architecture AMD 64 permet le calcul 32 et 64 bits Athlon 64 FX / Athlon 64 x2 / Sempron Prend en charge Hyper Transport et Cool’n’Quiet (Watt maximum : 95W) Bus frontal Chipset Super E/S Prend en charge Hyper Transport jusqu'à une bande passante de1 GHz GeForce 6150 SE/nForce 430 ITE 8716F Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S Moniteur de matériel patrimoniales la plu
MCP6P M2+ SPEC Chaque connecteur prend en charge 1 périphérique Connecteur SATA x4 Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant Connecteur d'entrée CD x1 Prend en charge la fonction d'entrée audio de CD Connecteur de sortie S/PDIF x1 Embase de ventilateur UC x1 Embase de ventilateur système x1 Embase d'effacement CMOS x1 Connecteur USB x3 Connecteur d'alimentation
Motherboard Manual ITALIAN SPECIFICA Socket AM2+ CPU Processori AMD Phenom / Athlon 64 / Athlon 64 FX / Athlon 64 x2 / Chipset Supporto di HyperTransport fino a1 GHz di larghezza di banda GeForce 6150 SE/nForce 430 ITE 8716F Super I/O Funzioni di controllo dell’ambiente: Fornisce le funzionalità legacy Super Monitoraggio hardware I/O usate più comunemente.
MCP6P M2+ SPECIFICA Connettore pannello frontale x1 Supporta i servizi del pannello frontale Connettore audio frontale x1 Supporta la funzione audio pannello frontale Connettore CD-in x1 Supporta la funzione input audio CD Connettore output SPDIF x1 Supporta la funzione d’output audio digitale Collettore ventolina CPU x1 Collettore ventolina sistema x1 Collettore cancellaz ione CMOS x1 Connettore USB x3 Connettore alimentazione x1 Alimentazione ventolina CPU (con funzione Smart Fan) Al
Motherboard Manual SPANISH Especificación Conector AM2+ CPU Procesadores AMD Phenom / Athlon 64 / Athlon 64 FX / Athlon 64 x2 / Sempron (Vatio máximo: 95W) FSB Conjunto de chips 64 bits Soporta las tecnologías Hyper Transport y Cool’n’Quiet Admite HyperTransport con un ancho de banda de hasta1 GHz GeForce 6150 SE/nForce 430 ITE 8716F Súper E/S La arquitectura AMD 64 permite el procesado de 32 y Iniciativas de control de entorno, Le ofrece las funcionalidades heredadas de Monitor hardware uso más co
MCP6P M2+ Especificación Conector de panel frontal X1 Soporta instalaciones en el panel frontal Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal Conector de entrada de CD X1 Soporta función de entrada de sonido de CD Conector de salida S/PDIF X1 Soporta función de salida de sonido digital Cabecera de ventilador de CPU X1 Cabecera de ventilador de sistema X1 Cabecera de borrado de CMOS X1 Conector USB X3 Conector de alimentación X1 Fuente de alimentación de ve
Motherboard Manual PORTUGUESE ESPECIFICAÇÕES Socket AM2+ CPU Processadores AMD Phenom / Athlon 64 / Athlon 64 FX / Athlon 64 x2 / Sempron (Watt máximo: 95W) FSB Chipset o Super I/O GeForce 6150 SE/nForce 430 Iniciativas para controlo do ambiente Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O.
MCP6P M2+ ESPECIFICAÇÕES Conector SATA x4 Cada conector suporta 1 dispositivo SATA Conector do painel frontal x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Suporta a função de áudio no painel frontal Conector para entrada de CDs x1 Suporta a entrada de áudio a partir de CDs Conector de saída S/PDIF x1 Suporta a saída de áudio digital Conector da ventoinha da CPU x1 Conector da ventoinha do sistema x1 Conector para limpeza do CMOS x1 Conector USB x3 C
Motherboard Manual POLISH SPEC Socket AM2+ Procesor AMD Phenom / Athlon 64 / Athlon 64 FX / Athlon 64 x2 / Sempron Procesory Chipset Obsługa HyperTransport o szerokości pasma do1 GHz GeForce 6150 SE/nForce 430 Gniazda DDR2 DIMM x 2 Moduł pamięci DDR2 z trybem podwójnego kanału Pamięć Maks.
MCP6P M2+ SPEC Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze wejścia CD x1 Obsługa funkcji wejścia audio CD Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia audio Złącze główkowe wentylatora procesora x1 Złącze główkowe wentylatora systemowego x1 Zasilanie wentylatora procesora (z funkcją Smart Fan) Zasilanie wentylatora systemowego Złącze główkowe kasowania Back Panel I/O Wymiary płyty Funkcje specjalne CMOS x1 Złącze USB x3 Złącze zasilania (24 pi
Motherboard Manual RUSSIAN СПЕЦ CPU Гнездо AM2+ (центральн Процессоры AMD Phenom / Athlon 64 / ый Athlon 64 FX / Athlon 64 X2 / Sempron процессор) (Максимальный ватт: 95W) FSB Набор микросхем Архитектура AMD 64 разрешать обработка данных на 32 и 64 бит Поддержка Hyper Transport и Cool’n’Quiet Поддержка HyperTransport с пропускной способностью до1GГц GeForce 6150 SE/nForce 430 Модуль памяти с двухканальным режимом DDR2 Слоты DDR2 DIMM x 2 Основная Максимальная ёмкость памяти 8 ГБ Поддержка DDR2 533
MCP6P M2+ СПЕЦ Разъём на лицевой панели x1 Поддержка устройств на лицевой панели Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели Разъём ввода для CD x1 Поддержка функции ввода для CD Разъём вывода для S/PDIF x1 Поддержка вывода цифровой звуковой функции Контактирующее приспособление x1 вентилятора центрального процессора Контактирующее приспособление вентилятора системы x1 Источник питания для вентилятора центрального процессора (с функцией интеллектуального вентилятора
Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت AM2+ﻡﻘﺒﺲ إﺝﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺏﻴﺔ ﺏﺴﺮﻋﺔ 32و 64ﺏﺖAMD 64ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ AMD Phenom / Athlon 64 /ﻡﻌﺎﻟﺠﺎت اﻟﻤﺮآﺰﻳﺔ Cool’n’Quiet Athlon 64 FX / Athlon 64 x2 / Sempronو Hyper Transportﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ )و: 95ﻗﺼ ﻮى واط( اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ اﻟﺠﺎﻥﺒﻲ ﺗﺮدد 1000ﺏﺘﺮدد ﻳﺼﻞ إﻟﻰ HyperTransportﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ GeForce 6150 SE/nForce 430 ﻓﺘﺤﺔ DDR2 DIMM ﻋﺪد2 ﻡﺰدوﺝﺔ اﻟﻘﻨﺎةDDR2وﺣﺪة ذاآﺮة ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 8ﺝﻴﺠﺎ
MCP6P M2+ اﻟﻤﻮاﺻﻔﺎت ﻡﻨﺎﻓﺬ دﺥﻞ/ﺥﺮج اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ﻡﻨﻔﺬ SATA ﻋﺪد 4 SATAﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻋﺪد 1 ﻳﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺏﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ CD-IN ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻡﺞ ﻡﻨﻔﺬ ﺥﺮج S/PDIF ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ وﺹﻠﺔ ﻡﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ ﻋﺪد 1 Smart Fanﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔ وﺹﻠﺔ ﻡﺮوﺣﺔ اﻟﻨﻈﺎم ﻋ
Motherboard Manual JAPANESE 仕様 Socket AM2+ CPU FSB AMD 64アーキテクチャでは、32ビットと64ビット計算が可 AMD Phenom / Athlon 64 / Athlon 64 FX / 能です Athlon 64 x2/ Sempron プロセッサ ハイパートランスポートとクールアンドクワイアットをサポ (最高のワット: 95W) ートします 1GHzのバンド幅までハイパートランスポート をサポートします チップセット GeForce 6150 SE/nForce 430 DDR2 DIMMスロット x 2 デュアル チャンネルモードDDR2メモリモジュール 最大メモリ容量8GB メインメモリ 各DIMMは 256MB/512MB & 1GB/2GB/ 4GB DDR2をサポート ITE 8716F Super I/O グラフィック DDR2 533 / 667 / 800 / 1066をサポート 登録済みDIMMとECC DIMMはサポートされません 環境コントロールイニシアチブ、 もっとも一般に使用されるレガシーSup
MCP6P M2+ 仕様 SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします フロントパネルコネクタ x1 フロントパネル機能をサポートします フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします CDインコネクタ x1 CDオーディオイン機能をサポートします S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x1 システムファン電源装置 CMOSクリアヘッダ x1 USBコネクタ x3 各コネクタは2つのフロントパネルUSBポートをサポートし ます 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 VGAポート x1 シリアルポート x1 LANポート x1 USBポート x4 オーディオジャック x3 背面パネル I/O ボードサイズ 190 mm (幅) X 244 mm (高さ)