iDEQ-T1 IN294KT1 Setup Manual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
iDEQ-T1 IN294KT1 Setup Manual Table of Contents Chapter 1: Introduction ..................................................................................... 1 Getting Started ............................................................................................. 1 Package Checklist ....................................................................................... 1 Specification .................................................................................................
iDEQ-T1 IN294KT1 Setup Manual Chapter 1: Introduction Getting Started To assure the safe application of the mini PC, please carefully read the following: Before disassembling or cleaning this product, make sure the power connector is unplugged. Keep the mini PC away from excessive moisture, direct sunlight, and extreme heat and cold. Keep liquids away from the mini PC and keyboard. Never wipe the interior of the system with water or dip the system in water.
iDEQ-T1 IN294KT1 Setup Manual Specification Processor iDEQ-T1 IN294KT1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz) Graphics Integrated Intel® HD Graphics series graphic engine Memory Supports Dual Channel DDR3L 1333 (1.35V/1.5V) 2x DDR3L SO-DIMM Memory Slot, Max. Supports up to 16 GB Memory Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8GB DDR3L module * Please refer to www.biostar.com.tw for Memory support list.
iDEQ-T1 IN294KT1 Setup Manual Getting to Know Your System Front Panel Rear Panel 3
iDEQ-T1 IN294KT1 Setup Manual Chapter 2: System hardware installation Disassembling the Cover 1. Loosen four screws on the bottom cover, then turn the system over. 2. Place the tip of your fingernail into the tiny gap between the cover and the chassis, then pull up the cover. 3. Loosen four screws of HDD Bracket.
iDEQ-T1 IN294KT1 Setup Manual 4. After removing the HDD bracket, you will see the system board. A. Installing WiFi Module Insert WiFi module into mini PCIe slot and fasten screw. Connect antenna line to “MAIN” on the WiFi module. Note: Wi-Fi module sold separately B. Installing Memory Module (1.35V/1.5V) Insert memory module into SODIMM socket at backside of motherboard. Note: The DIMM must be installed to DIMMA1 slot first.
iDEQ-T1 IN294KT1 Setup Manual C. Installing a 2.5 inch HDD 1. Fasten HDD bracket with HDD. 2. Connect the SATA cable to the HDD and system board. 3. Screw the HDD bracket back to the system.
iDEQ-T1 IN294KT1 Setup Manual VESA Bracket (Optional) 1. The mounting kit has either the VESA 75 mm or 100 mm mounting pattern. 2. Secure the VESA mounting bracket to your monitor with four screws. 3. Place your PC on VESA bracket and make sure the PC is hooked by the VESA mounting bracket.
iDEQ-T1 IN294KT1 Setup Manual Antenna Fasten antenna to the connector. Note: After the system assembly, please place the rubber stand to each screw hole.
iDEQ-T1 IN294KT1 Setup Manual Chapter 3: BIOS Setup Introduction The purpose of this manual is to describe the settings in the AMI UEFI BIOS Setup program on this motherboard. The Setup program allows users to modify the basic system configuration and save these settings to NVRAM. UEFI BIOS determines what a computer can do without accessing programs from a disk. This system controls most of the input and output devices such as keyboard, mouse, serial ports and disk drives.
iDEQ-T1 IN294KT1 Setup Manual Using Setup When starting up the computer, press during the Power-On Self-Test (POST) to enter the UEFI BIOS setup utility. In the UEFI BIOS setup utility, you will see General Help description at the top right corner, and this is providing a brief description of the selected item. Navigation Keys for that particular menu are at the bottom right corner, and you can use these keys to select item and change the settings.
iDEQ-T1 IN294KT1 Setup Manual Main Menu Once you enter AMI UEFI BIOS Setup Utility, the Main Menu will appear on the screen providing an overview of the basic system information. BIOS Information It shows system information including UEFI BIOS version, Product Name, Build Date and etc. Total Memory Shows system memory size, VGA shard memory will be excluded. System Language Choose the system default language. System Date Set the system date. Note that the ‘Day’ automatically changes when you set the date.
iDEQ-T1 IN294KT1 Setup Manual Advanced Menu The Advanced Menu allows you to configure the settings of CPU, Super I/O, Power Management, and other system devices. Beware of that setting inappropriate values in items of this menu may cause system to malfunction. ACPI Settings Enable ACPI Auto Configuration This item enables or disables BIOS ACPI Auto Configuration.
iDEQ-T1 IN294KT1 Setup Manual Enable Hibernation This item enables or disables system ability to hibernate (OS/S4 Sleep State). This option may be not effective with some OSes. Options: Enabled (Default) / Disabled ACPI Sleep State This item selects the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. Options: S3 only (Suspend to RAM) (Default) / Suspend Disabled Lock Legacy Resources The item enables or disables Lock of Legacy Resources.
iDEQ-T1 IN294KT1 Setup Manual SMART FAN Control System Smart Fan2 This item allows you to control the System Smart Fan function.
iDEQ-T1 IN294KT1 Setup Manual Intel (R) Smart Connect Technology ISCT Support This item enables/disables ISCT Support. Options: Disabled (Default) / Enabled Note: The following items appear only when you set the ISCT Support function to [Enabled] ISCT Notification Control Options: Enabled (Default) CPU Configuration This item shows CPU Information Active Processor Cores This item sets number of cores to enable in each processor package.
iDEQ-T1 IN294KT1 Setup Manual Limit CPUID Maximum Disabled for Windows XP Options: Disabled (Default) / Enabled Execute-Disable Bit XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, Red Hat Enterprise 3 Update 3.). Options: Enabled (Default) / Disabled Hardware Prefetcher This item enables or disables the Mid Level Cache (L2) streamer Prefetcher.
iDEQ-T1 IN294KT1 Setup Manual CPU C7 report This item enables or disables CPU C7 (ACPI C3) report to OS. Options: Enabled (Default) / Disabled Package C State limit This item sets Package C State limit. Options: No Limit (Default) / C0 / C1 / C3 / C6 / C7 SATA Configuration The BIOS will automatically detect the presence of SATA devices. Serial-ATA (SATA) This item enables/disables Serial ATA Device. Options: Enabled (Default) / Disabled SATA Mode This item determines how SATA controller(s) operate.
iDEQ-T1 IN294KT1 Setup Manual Network Stack Configuration Network Stack This item enables or disables UEFI network stack Options: Disabled (Default) / Enabled Note: The following items appear only when you set the Network Stack function to [Enabled] IPv4 PXE Support This item enables or disables IPv4 PXE Boot Support. If disabled IPv4 booth option will not be created. Options: Enabled (Default) / Disabled IPv6 PXE Support This item enables or disables IPv6 PXE Boot Support.
iDEQ-T1 IN294KT1 Setup Manual CSM Configuration CSM Support This item enables or disables CSM Support Options: Enabled (Default) / Disabled GateA20 Active Upon Request – FA20 can be disabled using BIOS services. Always – do not allow disabling GA20; this option is useful when any RT code is executed above 1MB Options: Upon Request (Default) / Always Option ROM Messages This item sets the display mode for option ROM.
iDEQ-T1 IN294KT1 Setup Manual Storage This item controls the execution of UEFI and Legacy Storage OpROM Options: Legacy only (Default) / Do not launch / UEFI only / Legacy first / UEFI first Video This item controls the execution of UEFI and Legacy Video OpROM Options: Legacy only (Default) / Do not launch / UEFI only / Legacy first / UEFI first Other PCI device It determines OpROM execution policy for devices other than Network, Storage, or video.
iDEQ-T1 IN294KT1 Setup Manual EHCI Hand-off This is workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. Options: Disabled (Default) / Enabled USB Mass Storage Driver Support The item allows you to enable or disable USB Mass Storage Driver Support. Options: Enabled (Default) / Disabled USB transfer time-out The time-out value for Control, Bulk, and Interrupt transfers.
iDEQ-T1 IN294KT1 Setup Manual Chipset Menu This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components. Beware of that setting inappropriate values in items of this menu may cause system to malfunction.
iDEQ-T1 IN294KT1 Setup Manual IGD Turbo Enable Enable: IGD Turbo Enable. Disable: IGD Turbo Disable. Options: Enabled (Default) / Disabled Primary Display This item selects which of IGD/PCI Graphics device should be Primary Display. Options: IGD (Default) / PCI PAVC This item enables/disables Protected Audio Video Control. Options: LITE Mode (Default) / Disabled / SERPENT Mode DVMT Pre-Allocated This item selects DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device.
iDEQ-T1 IN294KT1 Setup Manual South Bridge USB Configuration XHCI Mode This item enables or disables mode of operation of xHCI controller. Options: Smart Auto (Default) / Auto / Enabled / Disabled USB 2.0(EHCI) Support This item controls the USB EHCI (USB2.0) functions. One EHCI controller must always be enabled.
iDEQ-T1 IN294KT1 Setup Manual USB Per Port Controller This item controls each of the USB ports(0-3). Enable: Enable USB per port; Disable: Use USB port x setting. Options: Enabled (Default) / Disabled USB Port 0/1/2/3 This item enables/disables USB port 0/1/2/3 Options: Enabled (Default) / Disabled PCI Express Configuration ASPM This item sets PCI Express Active State Power Management settings. Options: Auto (Default) / L0s / L1 / L0sL1 / Disabled Speed This item selects PCI Express port speed.
iDEQ-T1 IN294KT1 Setup Manual Security Menu Administrator Password This item sets Administrator Password. User Password This item sets User Password. Secure Boot Menu Secure Boot Secure Boot flow control. Secure Boot can be enabled only when 1. Platform Key (PK) is enrolled and Platform is operating in user mode and 2.CSM function is disabled in Setup.
iDEQ-T1 IN294KT1 Setup Manual Note: The following items appear only when you set the Secure Boot function to [Enabled] Key Management Enroll All Factory Default Keys Forces system to user Mode – Install all Factory Default keys (PK, KEK, dbx, dbt). Change takes effect after boot. Platform Key (PK) Delete PK – Allows you to delete the PK file from your system. Set new PK – Allows you set new PK file. Key Exchange Key Database (KEK) Delete KEK – Allows you to delete the KEK file from your system.
iDEQ-T1 IN294KT1 Setup Manual Performance Menu This submenu allows you to change voltage and clock of various devices. (However, we suggest you use the default setting. Changing the voltage and clock improperly may damage the device.) Notice Beware of that setting inappropriate values in items of this menu may cause system to malfunction. The options and default settings might be different by RAM or CPU models. DRAM Voltage This item sets DRAM Voltage. Options: Auto (Default) / 1.35V / 1.40V / 1.
iDEQ-T1 IN294KT1 Setup Manual Row Precharge Time (tRP) This item allows you to select Row Precharge Time, Range 3-15 Options: Auto (Default) RAS# Active Time (tRAS) This item allows you to select Row Active Time, Range 9-63 Options: Auto (Default) Write Recovery Time (tWR) This item allows you to select Internal Write to Read Command Delay, Range 5-16 Options: Auto (Default) Row Refresh Cycle Time (tRFC) This item allows you to select Minimum Refresh Recovery Time, Range 1-511 Options: Auto (Default)
iDEQ-T1 IN294KT1 Setup Manual Boot Menu This menu allows you to setup the system boot options. Setup Prompt Timeout This item sets number of seconds to wait for setup activation key. Options: 1 (Default) Bootup NumLock State This item selects the keyboard NumLock state. Options: On (Default) / Off Full Screen Logo Display This item allows you to enable/disable Full Screen Logo Show function.
iDEQ-T1 IN294KT1 Setup Manual Exit Menu This menu allows you to load the optimal default settings, and save or discard the changes to the BIOS items. Discard Changes and Exit Abandon all changes made during the current session and exit setup. Save Changes and Reset Reset the system after saving the changes. Restore Defaults This selection allows you to reload the BIOS when problem occurs during system booting sequence. These configurations are factory settings optimized for this system.
iDEQ-T1 IN294KT1 Setup Manual Chapter 4: BIOS Update & Software BIOS Update The BIOS can be updated using either of the following utilities: BIOSTAR BIOS Flasher: Using this utility, the BIOS can be updated from a file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a CD-ROM. BIOSTAR BIOS Update Utility: It enables automated updating while in the Windows environment.
iDEQ-T1 IN294KT1 Setup Manual 6. Select the proper BIOS file, and a message asking if you are sure to flash the BIOS file. Click Yes to start updating BIOS. 7. A dialog pops out after BIOS flash is completed, asking you to restart the system. Press the [Y] key to restart system. 8. While the system boots up and the full screen logo shows up, press key to enter BIOS setup.
iDEQ-T1 IN294KT1 Setup Manual 4. An open dialog will show up to request your agreement to start the BIOS update. Click Yes to start the online update procedure. 5. If there is a new BIOS version, the utility will ask you to download it. Click Yes to proceed. 6. After the download is completed, you will be asked to program (update) the BIOS or not. Click Yes to proceed. 7. After the updating process is finished, you will be asked you to reboot the system. Click OK to reboot. 8.
iDEQ-T1 IN294KT1 Setup Manual 4. A warning message will show up to request your agreement to start the BIOS update. Click OK to start the update procedure. 5. Choose the location for your BIOS file in the system. Please select the proper BIOS file, and then click on Open. It will take several minutes, please be patient. 6. After the BIOS Update process is finished, click on OK to reboot the system. 7. While the system boots up and the full screen logo shows up, press key to enter BIOS setup.
iDEQ-T1 IN294KT1 Setup Manual Software Installing Software 1. Insert the Setup DVD to the optical drive. The driver installation program would appear if the Auto-run function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process is completed, you will see the software icon showing on the desktop. Double-click the icon to launch it.
iDEQ-T1 IN294KT1 Setup Manual eHot-Line eHot-Line is a convenient utility that helps you to contact with our Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem. Note: Before you use this utility, please set Outlook Express as your default e-mail client application program. represents important information that you must provide.
iDEQ-T1 IN294KT1 Setup Manual Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail. Note1: We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service.
iDEQ-T1 IN294KT1 Setup Manual Smart Connect Technology Intel® Smart Connect Technology is designed to update programs by periodically waking your computer from sleep/standby mode for a short time. This function works with applications that automatically get their data from the Internet. System Requirement: Intel Smart Connect Technology enabled in BIOS Setup Set the “ACPI Sleep State” to S3 in BIOS Setup. Windows 7, Windows 8 and Windows 8.
iDEQ-T1 IN294KT1 Setup Manual Configuration Utility The Intel Smart Connect Technology Configuration Utility allows configuration of the sleep duration, extended hours sleep duration, and viewing of the Event History along with other settings. To launch the application, select the application “Intel® Smart Connect Technology in the Start menu (Windows* 7) or Start screen (Windows* 8/8.1) to launch the configuration GUI.
K-BAR iDEQ-T1 IN294KT1 Setup Manual K-BAR is a windows-based audio utility which allows you to synchronize recording from song and voice, change the pitch of background music and reduce the original vocal volume in songs. After finishing driver installation, you can find this utility in control panel. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Smart EAR iDEQ-T1 IN294KT1 Setup Manual Smart EAR is a windows-based audio utility which allows you to easily adjust system volume. With its user-friendly GUI, you can also adjust impedance setting (Low/High Gain) to optimize your headphone performance. High/Low Gain Switch: Keep the gain switch to low for low impedance headphone and set to high for high impedance headphone.
iDEQ-T1 IN294KT1 Setup Manual Chapter 5: Useful Help Driver Installation After you installed your operating system, please insert the Fully Setup Driver DVD into your optical drive and install the driver for better system performance. You will see the following window after you insert the DVD The setup guide will auto detect your motherboard and operating system. A. Driver Installation To install the driver, please click on the Driver icon.
iDEQ-T1 IN294KT1 Setup Manual Troubleshooting Probable Solution 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 1. Make sure power cable is securely plugged in. 2. Replace cable. 2. Indicator light on keyboard does not shine. 3. Contact technical support. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running.
iDEQ-T1 IN294KT1 Setup Manual Appendix: Specification In Other Languages Arabic ااﻟﻤﻌﺎﻟﺞ اﻟﺠﺮاﻓﻴﻜﺲ )iDEQ-T1 IN294KT1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz ﻣﺸﻐﻞ ﺳﻠﺴﻠﺔ ﺟﺮاﻓﻴﻜﺲ® Intelﻋﺎﻟﻴﺔ اﻟﺪﻗﺔ اﻟﻤﺘﻜﺎﻣﻠﺔ ) 1.35ﻓﻮﻟﺖ 1.5 /ﻓﻮﻟﺖ(DDR3L 1333ﻳﺪﻋﻢ اﻟﻘﻨﺎة اﻟﻤﺰدوﺟﺔ ،ذاآﺮةﺗﺪﻋﻢ ﻣﺎ ﻳﺼﻞ إﻟﻰ 16ﺟﻴﺠﺎ ﺑﺎﻳﺖ آﺤﺪ أﻗﺼﻰ2x DDR3L SO-DIMMﻓﺘﺤﺔ ذاآﺮة 512 DDR3Lﻣﻴﺠﺎﺑﺎﻳﺖ 8 /4 /2 /1 /ﺟﻴﺠﺎ ﺑﺎﻳﺖ وﺣﺪة non-ECCﺗﺪﻋﻢDIMMآﻞ ﻟﻘﺎﺋﻤﺔ دﻋﻢ اﻟﺬاآﺮة *www.biostar.com.tw.
iDEQ-T1 IN294KT1 Setup Manual French Processeur iDEQ-T1 IN294KT1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz) Graphique Intégré Intel® HD Série Graphique Moteur Graphique Mëmoire Soutient Canal double DDR3L 1333 (1.35V/1.5V) 2x DDR3L SO-DIMM Créneau de Mémoire, Max. Supporte jusqu’à 16 GB de Mémoire Chaque DIMM supporte non-ECC 512MB/ 1/ 2/ 4/ 8GB DDR3L Module * Référez-vous s’il vous plaît à www.biostar.com.tw pour la liste de soutien de mémoire.
iDEQ-T1 IN294KT1 Setup Manual German Prozessor iDEQ-T1 IN294KT1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz) Grafik Integrierter Intel® HD Grafik Serie grafischer Motor Speicher Unterstützt Doppelkanal DDR3L 1333 (1.35V/1.5V) 2x DDR3L SO-DIMM Speicher Schlitz, Max. Unterstützt bis 16 GB Speicher Jeder DIMM unterstützt non-ECC 512MB/ 1/ 2/ 4/8 GB DDR3L Modul * Bitte konsultieren Sie www.biostar.com.tw für die Unterstützungsliste des Speichers.
iDEQ-T1 IN294KT1 Setup Manual Portuguese Processador iDEQ-T1 IN294KT1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz) Gráficos Motor gráfico Intel® da série HD Graphics integrado Memória Suporta Canal Duplo DDR3L 1333 (1.35V/1.5V) Ranhura de Memória 2x DDR3L SO-DIMM, Max. Suporta até 16 GB de memória Cada DIMM suporta módulo não-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L * Por favor, refira awww.biostar.com.tw para a lista de suporte de memória.
iDEQ-T1 IN294KT1 Setup Manual Russian Процессор iDEQ-T1 IN294KT1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz) Графики Интегрированные Intel® HD графики серии графического процессора Память Поддерживает Двойной канал DDR3L 1333 (1.35V/1.5V) 2xDDR3L SO-DIMM Слот памяти, макс. поддерживает до 16Гб памяти Каждый DIMM (модуль памяти с двухрядным расположением выводов) поддерживает не-ECC 512Мб/ 1/ 2/ 4/ 8 Гб DDR3L модуля * Для перечня поддержания памяти смотрите www.biostar.com.tw.
iDEQ-T1 IN294KT1 Setup Manual Japanese プロセッサ iDEQ-T1 IN294KT1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz) グラフィックス Integrated Intel® HD グラフィックス シリーズ グラフィック エンジン メモリ デュアル チャンネル DDR3L 1333 (1.35V/1.5V) 対応 2x DDR3L SO-DIMM メモリ スロットは、メモリ最大16 GBまで対応 各 DIMM はnon-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L モジュール対応 * www.biostar.com.
iDEQ-T1 IN294KT1 Setup Manual Spanish Procesador iDEQ-T1 IN294KT1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz) Gráfico Serie de Intel ® HD Gráfico motor gráfico integrado Memoria Sportar Canal Dual DDR3L 1333 (1.35V/1.5V) Muesca de Memoria 2x DDR3L SO-DIMM, Soportar Memoria Max. de 16 GB Cada DIMM soporta modulo non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L Por favor refiere la www.biostar.com.tw para la lista de soporte de Memoria.