G41U3G Setup Manual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Chapter 1: Introduction ............................................................ 1 1.1 Before You Start ................................................................................ 1 1.2 Package Checklist ............................................................................. 1 1.3 Motherboard Features...................................................................... 2 1.4 1.5 Rear Panel Connectors .....................................................................
G41U3G CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation.
Motherboard Manual 1.3 MOTHERBOARD FEATURES SPEC LGA 775 Supports Hyper-Threading / Execute Disable Bit / Intel Core2Duo / Core2Quad / CPU Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx processor Chipset Support 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 ITE 8721 Super I/O Environment Control initiatives, Provides the most commonly used legacy Hardware Monitor Controller Super I/O functionality.
G41U3G SPEC SATA Connector x4 Each connector supports 1 SATA device Front Panel Connector x1 Supports front panel facilities Front Audio Connector x1 Supports front panel audio function CPU Fan Header x1 CPU Fan power supply (with Smart Fan function) System Fan Header x1 System Fan Power supply Clear CMOS Header x1 Restore CMOS data to factory default USB 2.0 Connector x2 Each connector supports 2 front panel USB 2.
Motherboard Manual 1.5 MOTHERBOARD LAYOUT KBMS1 LGA775 ATXPWR1 CPU1 VGA1 CPU_FAN1 DDR3_B1 DDR3_A1 ATXPWR2 JUSBV1 JUSBV2 USB3_0 IDE1 Intel G41 RJ45USB1 BIOS AUD IO1 F_AUDIO1 PEX16_1 LAN PCI1 PCI2 J_PRIN T1 J_ COM1 SYS_FAN1 F_ USB1 Super I/O Intel ICH 7 F_USB2 Codec FDD1 Note: ■ represents the 1st pin.
G41U3G CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Pin-Cap Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a 90-degree angle.
Motherboard Manual Step 2: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 2-1: Step 2-2: Step 3: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the CPU_FAN1. This completes the installation.
G41U3G 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different due to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. CPU_FAN1: CPU Fan Header 1 4 Pin 1 2 3 4 Assignment Ground Power FAN RPM rate sense Smart Fan Control Pin 1 2 3 Assignment Ground +12V FAN RPM rate sense SYS_FAN1: System Fan Header 3 1 Note: CPU_FAN1 supports 4-pin head connector; SYS_FAN1, 3-pin head one.
Motherboard Manual 2.3 INSTALLING SYSTEM MEMORY 8 DDR3_B1 DDR3_A1 A. DDR3 module 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
G41U3G B. Memory Capacity DIMM Socket Location DDR3 Module DDR3_A1 256MB/512MB/1GB/2GB/4GB DDR3_B1 256MB/512MB/1GB/2GB/4GB Total Memory Size Max is 8GB. C. Dual Channel Memory Installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table. Dual Channel Status DDR3_A1 DDR3_B1 Disabled O X Disabled X O Enabled O O (O means memory installed; X, not installed.
Motherboard Manual 2.4 CONNECTORS AND SLOTS FDD1: Floppy Disk Connector The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables. 2 34 1 33 IDE1: Hard Disk Connector The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.
G41U3G ATXPWR1: ATX Power Source Connector This connector allows user to connect 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground Pin 1 2 3 4 5 6 7 8 9 10 11 12 12 24 1 13 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.3V ATXPWR2: ATX Power Source Connector This connector provides +12V to CPU power circuit.
Motherboard Manual PEX16_1: PCI-Express x16 Slot - PCI-Express 1.0a compliant. Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally. PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins. 2X bandwidth over the traditional PCI architecture. PEX16_1 PCI1/PCI2: Peripheral Component Interconnect Slots This motherboard is equipped with 2 standard PCI slots.
G41U3G CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DETAIL SETTINGS PANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.
Motherboard Manual F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel This motherboard provides 2 USB 2.0 headers, which allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. F_USB1 F_USB2 2 10 1 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC JUSBV1/JUSBV2/JUSBV3: Power Source Headers for USB Ports Pin 1-2 Close: JUSBV1: +5V for USB ports at USB3_0.
G41U3G JCMOS1: Clear CMOS Header Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (Default). 1 3 1 Pin 2-3 Close: Clear CMOS data. 3 ※ Clear CMOS Procedures: 1. 2. 3. 4. 5. Remove AC power line. Set the jumper to “Pin 2-3 close”. Wait for five seconds. Set the jumper to “Pin 1-2 close”. Power on the AC. 6.
Motherboard Manual F_AUDIO1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable. 10 9 2 1 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense J_COM1: Serial port Connector The motherboard has a Serial Port Connector for connecting RS-232 Port.
G41U3G J_PRINT1: Printer Port Connector This header allows you to connector printer on the PC.
Motherboard Manual CHAPTER 4: USEFUL HELP 4.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.
G41U3G 4.2 SOFTWARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop. Double-click the icon to launch the utility.
Motherboard Manual After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .
G41U3G BIOS Update BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system. AWARD BIOS Show current BIOS information AMI BIOS Clear CMOS function (Only for AWARD BIOS) Save current BIOS to a .bin file Update BIOS with a BIOS file Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.
Motherboard Manual Before doing this, please download the proper BIOS file from the website. For AWARD BIOS, update BIOS procedure should be run with Clear CMOS function, so please check on Clear CMOS first. Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure.
G41U3G 4.3 EXTRA INFORMATION CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed.
Motherboard Manual BIO-Flasher BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive or floppy disk. The BIO-Flasher is built in the BIOS chip. To enter the utility, press during the Power-On Self Tests (POST) procedure while booting up. Updating BIOS with BIO-Flasher 1. Go to the website to download the latest BIOS file for the motherboard. 2. Then, save the BIOS file into a USB pen drive or a floppy disk. 3.
G41U3G 4.4 AMI BIOS BEEP CODE Boot Block Beep Codes Number of Beeps 1 2 3 4 5 7 10 11 12 13 Description No media present. (Insert diskette in floppy drive A:) “AMIBOOT.ROM” file not found in root directory of diskette in A: Insert next diskette if multiple diskettes are used for recovery Flash Programming successful File read error No Flash EPROM detected Flash Erase error Flash Program error “AMIBOOT.
Motherboard Manual 4.5 TROUBLESHOOTING Probable 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. Solution 1. 2. 3. Make sure power cable is securely plugged in. Replace cable. Contact technical support.
G41U3G This page is intentionally left blank.
Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen LGA 775 Unterstützt Hyper-Threading / Execute Disable Bit / Intel Core2Duo / Core2Quad / CPU Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx Prozessoren Chipsatz 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 Umgebungskontrolle, ITE 8721 Super E/A Bietet die häufig verwendeten alten Super Hardware-Überwachung E/A-Funktionen.
G41U3G Spezifikationen Onboard-Ans Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss Serieller Anschluss x1 IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen Front-Audioanschluss x1 CPU-Lüfter-Sockel x1 System-Lüfter-Sockel x1 "CMOS löschen"-Sockel
Motherboard Manual FRENCH SPEC LGA 775 Processeurs Intel Core2Duo / Core2Quad UC / Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx Prend en charge les technologies Hyper-Threading / d'exécution de bit de désactivation / Intel SpeedStep® optimisée/ d'architecture Intel 64 / de mémoire étendue 64 / de virtualisation (Watt maximum : 95W) Bus frontal 800 / 1066 / 1333 MHz Chipset Super E/S Intel G41 Intel ICH7 ITE 8721 Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S
G41U3G SPEC Chaque connector prend en charge 2 lecteurs de Connecteur de disquette x1 Connecteur de Port d'imprimante x1 Port série x1 Connecteur IDE x1 Connecteur SATA x4 Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant Connecteur Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant embarqué Alimentation électrique du ventilateur UC (avec fonction Embase de ventilateur UC x1 Embase de ventilateur système x1 Embase d'eff
Motherboard Manual ITALIAN SPECIFICA LGA 775 Supporto di Hyper-Threading / Execute Disable Processore Intel Core2Duo / CPU Bit / Enhanced Intel SpeedStep® / Architettura Core2Quad / Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx Intel 64 / Tecnologia Extended Memory 64 / Tecnologia V irtualization (Watt massimo: 95W) FSB Chipset 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 Funzioni di controllo dell’ambiente: ITE 8721 Super I/O Fornisce le funzionalità legacy Super Monitoraggio hardware I/O usa
G41U3G SPECIFICA Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante Porta seriale x1 Connettore IDE x1 Ciascun connettore supporta 2 unità IDE Connettore SATA x4 Ciascun connettore supporta 1 unità SATA Connettore pannello frontale x1 Supporta i servizi del pannello frontale Connettore audio frontale x1 Supporta la funzione audio pannello frontale Connettori Collettore ventolina CPU x1 Alimentazion
Motherboard Manual SPANISH Especificación LGA 775 Admite Hyper-Threading / Bit de deshabilitación de Procesador Intel Core2Duo / Core2Quad / CPU Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx ejecución / Intel SpeedStep® Mejorado / Intel Architecture-64 / Tecnología Extended Memory 64 / Tecnología de virtualización (Vatio máximo: 95W) FSB 800 / 1066 / 1333 MHz Conjunto de Intel G41 chips Intel ICH7 Iniciativas de control de entorno, ITE 8721 Súper E/S Le ofrece las funcionalidades heredadas
G41U3G Especificación Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora Puerto serie X1 Conector IDE X1 Cada conector soporta 2 dispositivos IDE Conector SATA X4 Cada conector soporta 1 dispositivos SATA Conector de panel frontal X1 Soporta instalaciones en el panel frontal Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal X1 Fuente de alimentación de venti
Motherboard Manual PORTUGUESE ESPECIFICAÇÕES LGA 775 Processador Intel Core2Duo / Core2Quad Suporta as tecnologias Hyper-Threading / Execute CPU / Pentium Dual-Core / Celeron Dual-Core / Disable Bit / Enhanced Intel SpeedStep® / Intel Arquitecture -64 / Extended Memory 64 / Virtualization Celeron 4xx (Watt máximo: 95W) FSB Chipset 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 ITE 8721 Especificaçã o Super I/O Iniciativas para controlo do ambiente Proporciona as funcionalidades mais utilizadas em termos
G41U3G ESPECIFICAÇÕES Conectores na placa Ranhura PCI Express x16 x1 Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes Conector da para impressora x1 Cada conector suporta 1 Porta para impressora Porta série x1 Conector IDE x1 Cada conector suporta 2 dispositivos IDE Conector SATA x4 Cada conector suporta 1 dispositivo SATA Conector do painel frontal x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Suporta a função de áud
Motherboard Manual POLISH SPEC LGA 775 Procesor Intel Core2Duo / Core2Quad / Procesor Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx Chipset Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology (Maksymalny Watt: 95W) FSB Obsługa Hyper-Threading / Execute Disable Bit / 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 Gniazda DDR3 DIMM x 2 Moduł pamięci DDR3 z trybem podwójnego kanału Pamięć Każde gniazdo DIMM obsługuje moduły Obsługa DDR3 800
G41U3G SPEC Złącza Złącze napędu dyskietek x1 Każde złącze obsługuje 2 napędy dyskietek Złącze Port drukarki x1 Każde złącze obsługuje 1 Port drukarki Port szeregowy x1 Złącze IDE x1 Każde złącze obsługuje 2 urządzenia IDE Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA Złącze panela przedniego x1 Obsługa elementów panela przedniego Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze główkowe wentylatora wbudowane procesora x1 Złącze główkowe wentylatora
Motherboard Manual RUSSIAN СПЕЦ CPU (центральн ый процессор) LGA 775 Процессор Intel Core2Duo / Core2Quad / Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx 800 / 1066 / 1333 МГц Набор Intel G41 Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / технологии виртуализация (Максимальный ватт: 95W) FSB Поддержка технологий Hyper-Threading / Execute микросхем Intel ICH7 Модуль памяти с двухканальным режимом DDR3 Слоты DDR3 DIMM x 2 Поддержка DDR3 800/1
G41U3G СПЕЦ Разъём НГМД x1 Разъём Порт подключения Встроенны й разъём Каждый разъём поддерживает 2 накопителя на гибких магнитных дисках Каждый разъём поддерживает 1 Порт подключения принтера x1 Последовательный порт x1 Разъём IDE x1 принтера Каждый разъём поддерживает 2 встроенных интерфейса накопителей Разъём SATA x4 Каждый разъём поддерживает 1 устройство SATA Разъём на лицевой панели x1 Поддержка устройств на лицевой панели Входной звуковой разъём x1 Поддержка звуковых функций на ли
Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت LGA 775 وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ Intel Core2Duo / Core2Quad /ﻣﻌﺎﻟﺠﺎت Pentium Dual-Core / Celeron Dual-Core / ﺑﺘﺮدد یﺼﻞ إﻟﻰ Celeron 4xx Hyper-Threading / Execute Disable Bit /ﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology )و: 95ﻗﺼ ﻮى واط( اﻟﻨﺎﻗﻞ اﻷﻣﺎﻣﻲ اﻟﺠﺎﻥﺒﻲ ﻣﻴﺠﺎ هﺮﺗﺰ 800 / 1066 / 1333ﺗﺮدد Intel G41 ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ Intel ICH7 ﻓﺘﺤ
G41U3G اﻟﻤﻮاﺻﻔﺎت اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺱﻄﺢ اﻟﻠﻮﺣﺔ ﻣﻨﻔﺬ ﻣﺤﺮك أﻗﺮاص ﻣﺮﻥﺔ ﻋﺪد 1 ﻣﻨﻔﺬ ﻃﺎﺑﻌﺔ ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ ﻋﺪد1 ﻣﻨﻔﺬ IDE ﻋﺪد 1 IDEیﺪﻋﻢ آﻞ ﻣﻨﻔﺬ اﺙﻨﻴﻦ ﻣﻦ أﺝﻬﺰة ﻣﻨﻔﺬ SATA ﻋﺪد 4 SATAیﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺝﻬﺰة ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ ﻋﺪد 1 یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ ﻋﺪد 1 یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد 1 وﺹﻠﺔ ﻣﺴﺢ CMOS ﻋﺪد 1 ﻣﻨﻔﺬ USB 2.
Motherboard Manual JAPANESE 仕様 LGA 775 Hyper-Threading / Execute Disable Bit / Enhanced Intel Intel Core2Duo / Core2Quad / CPU Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx processor Memory 64 Technology / Virtualization Technologyをサ ポートします (最高のワット: 95W) FSB SpeedStep® / Intel Architecture-64 / Extended 800 / 1066 / 1333 MHz Intel G41 チップセット Intel ICH7 デュアル チャンネルモードDDR3メモリモジュール DDR3 DIMMスロット x 2 各DIMMは 256MB / 512MB / 1GB / 2GB / メインメモリ 4GB DDR3をサポート DDR3 800/1066/1333(OC)をサポート 登録済みDIMMとE
G41U3G 仕様 フロッピーコネクタ x1 各コネクタは2つのフロッピードライブをサポートします プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします シリアルポート x1 IDEコネクタ x1 各コネクタは2つのIDEデバイスをサポートします SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします フロントパネルコネクタ x1 フロントパネル機能をサポートします x1 フロントパネルオーディオ機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x1 システムファン電源装置 CMOSクリアヘッダ x1 USB 2.0コネクタ x2 オンボードコ フロントオーディオコネクタ ネクタ 各コネクタは2つのフロントパネルUSB 2.