G41D-M7 Setup Manual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Chapter 1: Introduction ........................................ 1 1.1 1.2 1.3 1.4 1.5 Before You Start ................................................................................ 1 Package Checklist ............................................................................. 1 Motherboard Features...................................................................... 2 Rear Panel Connectors ..................................................................... 3 Motherboard Layout...
G41D-M7 CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation.
Motherboard Manual 1.3 MOTHERBOARD FEATURES SPEC LGA 775 Intel Core2Quad / Core2Duo / Pentium CPU Dual-Core / Celeron Dual-Core / Celeron 4xx processor Chipset Intel G41 Intel ICH7 Environment Control initiatives, Provides the most commonly used legacy Hardware Monitor Controller Super I/O functionality.
G41D-M7 SPEC SATA Connector x4 Each connector supports 1 SATA devices Front Panel Connector x1 Supports front panel facilities Front Audio Connector x1 Supports front panel audio function CPU Fan Header x1 CPU Fan power supply (with Smart Fan function) System Fan Header x1 System Fan Power supply Clear CMOS Header x1 Restore CMOS data to factory default USB Connector x2 Each connector supports 2 front panel USB ports Power Connector (24pin) x1 Connects to Power supply Power Connector
Motherboard Manual 1.5 MOTHERBOARD LAYOUT CPU_FAN1 ATXPWR2 KBMS1 C OM 1 C OM 1 LGA775 PR NT1 ATXPWR1 CPU1 D DR2_B1 D DR2_A1 VGA1 J USBV1 USB1 RJ45USB1 AUDIO1 LAN ID E1 Intel G41 BAT1 PEX16_1 Super I/O BI OS PCI1 JUSBV2 Intel ICH7 SATA2 FDD1 F_AUDIO1 F_COM1 Note: ■ represents the 1st pin.
G41D-M7 CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Pin-Cap Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a 90-degree angle.
Motherboard Manual Step 2: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 2-1: Step 2-2: Step 3: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the JCFAN1. This completes the installation.
G41D-M7 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.
Motherboard Manual 2.3 INSTALLING SYSTEM MEMORY 8 DD R2_B1 DD R2_A1 A. DDR2 module 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot so that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
G41D-M7 B. Memory Capacity DIMM Socket Location DDR2 Module DDR2_A1 256MB/512MB/1GB/2GB DDR2_B1 256MB/512MB/1GB/2GB Total Memory Size Max is 4GB. C. Dual Channel Memory Installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table. Dual Channel Status DDR2_A1 DDR2_B1 Disabled O X Disabled X O Enabled O O (O means memory installed, X means memory not installed.
Motherboard Manual 2.4 CONNECTORS AND SLOTS FDD1: Floppy Disk Connector The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables. 2 34 1 33 IDE1: IDE/ATAPI Connector The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.
G41D-M7 PEX16_1: PCI-Express x16 Slot - PCI-Express 1.0a compliant. Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally. PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins. 2X bandwidth over the traditional PCI architecture. PEX16_1 PCI1/PCI2: Peripheral Component Interconnect Slots This motherboard is equipped with 2 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards.
Motherboard Manual CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DETAIL SETTINGS PANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.
G41D-M7 ATXPWR1: ATX Power Source Connector This connector allows user to connect 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground 12 24 1 13 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.3V ATXPWR2: ATX Power Source Connector This connector provides +12V to CPU power circuit.
Motherboard Manual F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel This motherboard provides 2 USB 2.0 headers, which allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. 2 10 1 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC F_AUDIOF1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel.
G41D-M7 JCMOS1: Clear CMOS Header Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard. 3 1 Pin 1-2 Close: Normal Operation (Default). 3 3 1 Pin 2-3 Close: Clear CMOS data. 1 ※ Clear CMOS Procedures: 1. 2. 3. 4. 5. Remove AC power line. Set the jumper to “Pin 2-3 close”. Wait for five seconds. Set the jumper to “Pin 1-2 close”. Power on the AC. 6.
Motherboard Manual JUSBV1/JUSBV2: Power Source Headers for USB Ports Pin 1-2 Close: JUSBV1: +5V for USB ports at USB1/RJ45USB1. JUSBV2: +5V for USB ports at F_USB1/F_USB2. Pin 2-3 Close: JUSBV1: +5V STB for USB ports at USB1/RJ45USB1. JUSBV2: +5V STB for USB ports at F_USB1/F_USB2. 1 3 Pin 1-2 close JUSBV1 1 3 1 JUSBV2 3 Pin 2-3 close 3 1 F_COM1: Serial port Connector (Optional) The motherboard has a Serial Port Connector for connecting RS-232 Port.
G41D-M7 CHAPTER 4: USEFUL HELP 4.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.
Motherboard Manual 4.2 SOFTWARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop.
G41D-M7 After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .
Motherboard Manual BIOS Update BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system. AWARD BIOS Show current BIOS information AMI BIOS Online Update function Clear CMOS function (Only for AMI BIOS) (Only for AWARD BIOS) Save current BIOS to a .bin file Update BIOS with a BIOS file Once click on this button, the saving dialog will show. Choose the position to save file and enter file name.
G41D-M7 Before doing this, please download the proper BIOS file from the website. For AWARD BIOS, update BIOS procedure should be run with Clear CMOS function, so please check on Clear CMOS first. Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure.
Motherboard Manual (for AMI BIOS only) Automatically download and update the latest BIOS via internet; make sure that the computer is connected to the internet before using this function. After clicking on the Online Update button, the utility will search for the latest BIOS from internet. If there is a new BIOS version, the utility will ask you to download it. Click Yes to proceed.
G41D-M7 4.3 EXTRA INFORMATION CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed.
Motherboard Manual BIO-Flasher BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive or floppy disk. The BIO-Flasher is built in the BIOS chip. To enter the utility, press during the Power-On Self Tests (POST) procedure while booting up. Updating BIOS with BIO-Flasher 1. Go to the website to download the latest BIOS file for the motherboard. 2. Then, save the BIOS file into a USB pen drive or a floppy disk. 3.
G41D-M7 4.4 AMI BIOS BEEP CODE Boot Block Beep Codes Number of Beeps 1 2 3 4 5 7 10 11 12 13 Description No media present. (Insert diskette in floppy drive A:) “AMIBOOT.ROM” file not found in root directory of diskette in A: Insert next diskette if multiple diskettes are used for recovery Flash Programming successful File read error No Flash EPROM detected Flash Erase error Flash Program error “AMIBOOT.
Motherboard Manual 4.5 TROUBLESHOOTING Probable 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. Solution 1. 2. 3. Make sure power cable is securely plugged in. Replace cable. Contact technical support.
G41D-M7 This page is intentionally left bank.
Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen LGA 775 Unterstützt Hyper-Threading / Execute Disable Bit / Intel Core2Quad / Core2Duo / Pentium Enhanced Intel SpeedStep® / Intel Architecture-64 / CPU Dual-Core / Celeron Dual-Core / Celeron Extended Memory 64 Technology / Virtualization 4xx Prozessoren Technology (Maximales Watt: 95W) FSB 800 / 1066 / 1333 MHz Intel G41 Chipsatz Intel ICH7 ITE 8718F Umgebungskontrolle, Bietet die häufig verwendeten alten Super Hardware-Übe
G41D-M7 Spezifikationen Steckplätze PCI-Steckplatz x2 PCI Express x16 Steckplatz x1 Diskettenlaufwerkanschluss x1 Serieller Anschluss (fakultativ) x1 IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion CPU-Lüfter-Sockel x1 Onboard-Ans chluss Jeder Anschluss unterstützt 2 Diskettenla
Motherboard Manual FRENCH SPEC Prend en charge les technologies Hyper-Threading / LGA 775 UC Processeurs Intel Core2Quad / Core2Duo d'exécution de bit de désactivation / Intel SpeedStep® /Pentium Dual-Core / Celeron Dual-Core / optimisée/ d'architecture Intel 64 / de mémoire Celeron 4xx (Watt maximum : 95W) étendue 64 / de virtualisation Bus frontal 800 / 1066 / 1333 MHz Chipset Super E/S Intel G41 Intel ICH7 ITE 8718F Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/
G41D-M7 SPEC Chaque connecteur prend en charge 1 périphérique Connecteur SATA x4 Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant Embase de ventilateur UC x1 Embase de ventilateur système x1 Embase d'effacement CMOS x1 Connecteur USB x2 Connecteur d'alimentation x1 SATA Alimentation électrique du ventilateur UC (avec fonction de ventilateur intelligent) Alimentation élect
Motherboard Manual ITALIAN SPECIFICA LGA 775 Supporto di Hyper-Threading / Execute Disable Processore Intel Core2Quad / CPU Bit / Enhanced Intel SpeedStep® / Architettura Core2Duo /Pentium Dual-Core / Intel 64 / Tecnologia Extended Memory 64 / Celeron Dual-Core / Celeron 4xx Tecnologia V irtualization (Watt massimo: 95W) FSB Chipset 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 Funzioni di controllo dell’ambiente: ITE 8718F Super I/O Fornisce le funzionalità legacy Super Monitoraggio hardware I/O u
G41D-M7 SPECIFICA Connettore IDE x1 Ciascun connettore supporta 2 unità IDE Connettore SATA x4 Ciascun connettore supporta 1 unità SATA Connettore pannello frontale x1 Supporta i servizi del pannello frontale Connettore audio frontale x1 Supporta la funzione audio pannello frontale Collettore ventolina CPU x1 Alimentazione ventolina CPU (con funzione Smart Fan) Collettore ventolina sistema x1 Collettore cancellaz ione CMOS x1 Connettore USB x2 Alimentazione ventolina di sistema Ciascun
Motherboard Manual SPANISH Especificación CPU LGA 775 Admite Hyper-Threading / Bit de deshabilitación de Procesador Intel Core2Quad / Core2Duo ejecución / Intel SpeedStep® Mejorado / Intel /Pentium Dual-Core / Celeron Dual-Core / Architecture-64 / Tecnología Extended Memory 64 / Tecnología de virtualización Celeron 4xx (Vatio máximo: 95W) FSB 800 / 1066 / 1333 MHz Conjunto de Intel G41 chips Intel ICH7 Iniciativas de control de entorno, ITE 8718F Súper E/S Le ofrece las funcionalidades heredada
G41D-M7 Especificación Conector SATA X4 Cada conector soporta 1 dispositivos SATA Conector de panel frontal X1 Soporta instalaciones en el panel frontal Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con función Smart Fan) Cabecera de ventilador de sistema X1 Cabecera de borrado de CMOS X1 Conector USB X2 Conector de alimentación X1 Fuente de alimentación de ventilador de sistema C
Motherboard Manual PORTUGUESE ESPECIFICAÇÕES LGA 775 CPU Processador Intel Core2Quad / Core2Duo /Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx (Watt máximo: 95W) FSB Chipset o Super I/O Intel ICH7 Iniciativas para controlo do ambiente Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O.
G41D-M7 ESPECIFICAÇÕES Conectores na placa Conector da unidade de disquetes x1 Porta série (opcional) x1 Conector IDE x1 Cada conector suporta 2 dispositivos IDE Conector SATA x4 Cada conector suporta 1 dispositivo SATA Conector do painel frontal x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Suporta a função de áudio no painel frontal Conector da ventoinha da CPU x1 Conector da ventoinha do sistema x1 Conector para limpeza do CMOS x1 Conector USB x
Motherboard Manual POLISH SPEC Procesor LGA 775 Obsługa Hyper-Threading / Execute Disable Bit / Procesor Intel Core2Quad / Core2Duo Enhanced Intel SpeedStep® / Intel Architecture-64 / /Pentium Dual-Core / Celeron Dual-Core / Extended Memory 64 Technology / Virtualization Celeron 4xx (Maksymalny Watt: 95W) FSB Chipset 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 Gniazda DDR2 DIMM x 2 Pamięć Każde gniazdo DIMM obsługuje moduły główna 256MB / 512MB / 1GB / 2GB 256MB Super I/O.
G41D-M7 SPEC Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA Złącze panela przedniego x1 Obsługa elementów panela przedniego Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze główkowe wentylatora procesora x1 Złącze główkowe wentylatora systemowego x1 Zasilanie wentylatora procesora (z funkcją Smart Fan) Zasilanie wentylatora systemowego Złącze główkowe kasowania CMOS x1 Złącze USB x2 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe) x1 Klawiatur
Motherboard Manual RUSSIAN СПЕЦ CPU LGA 775 Поддержка технологий Hyper-Threading / Execute (центральн Процессор Intel Core2Quad / Core2Duo ый Disable Bit / Enhanced Intel SpeedStep® / Intel /Pentium Dual-Core / Celeron Dual-Core / Architecture-64 / Extended Memory 64 Technology / процессор) Celeron 4xx (Максимальный ватт: 95W) технологии виртуализация FSB 800 / 1066 / 1333 МГц Набор Intel G41 микросхем Intel ICH7 Основная память Графика Слоты DDR2 DIMM x 2 Модуль памяти с двухканальным режимо
G41D-M7 СПЕЦ Разъём SATA x4 Каждый разъём поддерживает 1 устройство SATA Разъём на лицевой панели x1 Поддержка устройств на лицевой панели Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели Источник питания для вентилятора центрального Контактирующее приспособление вентилятора центрального процессора процессора (с функцией интеллектуального вентилятора) x1 Контактирующее приспособление вентилятора системы x2 Источник питания для вентилятора системы Открытое контактирующее
Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت LGA 775 Hyper-Threading / Execute Disable Bit /ﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت Intel Core2Quad / Core2Duoﻣﻌﺎﻟﺠﺎت Enhanced Intel SpeedStep® / Intel Architecture-64 / وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ /Pentium Dual-Core / Celeron Dual-Core / Extended Memory 64 Technology / Virtualization اﻟﻤﺮآﺰیﺔ ﺑﺘﺮدد یﺼﻞ إﻟﻰ Celeron 4xx Technology )و: 95ﻗﺼ ﻮى واط( اﻟﻨﺎﻗﻞ اﻷﻣﺎﻣﻲ اﻟﺠﺎﻥﺒﻲ ﻣﻴﺠﺎ هﺮﺗﺰ 800 / 1066 / 1333ﺗﺮدد Intel G41 ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ Intel ICH7 ﻓﺘﺤﺔ
G41D-M7 اﻟﻤﻮاﺻﻔﺎت ﻓﺘﺤﺔ PCI ﻋﺪد 2 اﻟﻔﺘﺤﺎت ﻓﺘﺤﺔ PCI Express x16ﻋﺪد 1 ﻣﻨﻔﺬ ﻣﺤﺮك أﻗﺮاص ﻣﺮﻥﺔ ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ)اﺥﺘﻴﺎریّﺔ( ﻋﺪد1 ﻣﻨﻔﺬ IDE ﻋﺪد 1 IDEیﺪﻋﻢ آﻞ ﻣﻨﻔﺬ اﺙﻨﻴﻦ ﻣﻦ أﺝﻬﺰة ﻣﻨﻔﺬ SATA ﻋﺪد 4 SATAیﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺝﻬﺰة ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ ﻋﺪد 1 یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ اﻝﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ ﻋﺪد 1 یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ اﻝﻠﻮﺣﺔ وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد
Motherboard Manual JAPANESE 仕様 LGA 775 Hyper-Threading / Execute Disable Bit / Enhanced Intel Intel Core2Quad / Core2Duo / Pentium SpeedStep® / Intel Architecture-64 / Extended CPU Dual-Core / Celeron Dual-Core / Celeron Memory 64 Technology / Virtualization Technologyをサ 4xx processor ポートします (最高のワット: 95W) FSB 800 / 1066 / 1333 MHz Intel G41 チップセット Intel ICH7 DDR2 DIMMスロット x 2 デュアル チャンネルモードDDR2メモリモジュール 各DIMMは 256MB / 512MB / 1GB / 2GB DDR2 800/667をサポート メインメモリ DDR2をサポート 登録済みDIMMとECC DIMMはサポートされません 最大メモ
G41D-M7 仕様 PCIスロット x2 PCI Express x16スロット x1 フロッピーコネクタ x1 シリアルポート (任意) x1 IDEコネクタ x1 各コネクタは2つのIDEデバイスをサポートします SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします フロントパネルコネクタ x1 フロントパネル機能をサポートします フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x1 システムファン電源装置 CMOSクリアヘッダ x1 USBコネクタ x2 スロット 各コネクタは2つのフロッピードライブをサポートします オンボードコ ネクタ 各コネクタは2つのフロントパネルUSBポートをサポートし ます 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 シリアルポート x1 背面パネル プリンタポート x1