Owner's Manual

ManualsBrandsBiostar ManualsMotherboardsBiostar 915GL-M7 Ultra

915GL-M7 Ultra

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respec t to the

contents here and specially disclaims any implied warranties of merchantability

or fitness for any purpose. Further the vendor reserves the right to revise this

publication and to make changes to the contents here without obligation to

notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Summary of content (62 pages)

PAGE 1
915GL-M7 Ultra FCC Information and Copyright This equipment has been tes ted and found to comply with the limits of a Class B digital devic e, purs uant to Part 15 of the FCC Rules . T hese limits are designed to provide reasonable protec tion against harmful interference in a residential installation. T his equipment generates , uses and can radiate radio frequency energy and, if not ins talled and used in accordance with the instructions , may cause harmful interference to radio communications .
PAGE 2
Table of Contents Chapter 1: Introduction ...........................................................1 1.1 Motherboard Features .................................................. 1 1.2 Package Checklist......................................................... 4 1.3 Motherboard Layout .................................................... 5 Chapter 2: Hardware Installation ..........................................6 2.1 Central Processing Unit (CPU)...................................... 6 2.
PAGE 3
915GL-M7 Ultra CHAPTER 1: INTRODUCTION 1.1 MOTHERBOARD FEATURES A. Hardware CPU Supports socket 775. Supports Intel Pentium 4 /Celeron D processor. Front side bus at the following frequency ranges: 533 MT/s (133 MHz Core Clock) 800 MT/s (200 MHz Core Clock) Supports Hyper-Threading Technology. Chipset North Bridge: Intel 915GL. South Bridge: Intel ICH6. Dimensions Micro ATX Form Factor: 24.45cm (W) x 24.4cm (L) Main Memory Supports Dual Channel DDR-400/333.
PAGE 4
915GL-M7 Ultra Se rial ATA Controller integrated in ICH6. Supports 4 Serial ATA (SATA) ports. - Intel Advanced Host Controller (AHCI). Compliant with SATA 1.0 specification Data transfer rates up to 1.5Gb/s Slots Two 32-bit PCI bus master slots. One PCI-Extreme (PCI-EX) slot. - PCI-Express 1.0a compliant. - Supports data transfer speed up to 1 GB/s per direction. (See p.10 for detail information.) Supe r I/O Chip: ITE IT8712. Low Pin Count Interface.
PAGE 5
915GL-M7 Ultra Front Side On-board Pe ripherals 1 IDE connector supports 2 hard disk devices. 1 front panel header supports front panel facilities. 1 CD-in connector supports 1 CD-ROM audio-in device. 1 front audio header supports front panel audio function. 1 S/PDIF-Out connector supports digital audio-out function 1 chassi s open header supports PC case-opened warning function. 1 Floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes.
PAGE 6
915GL-M7 Ultra B. BIOS & Software BIOS Award legal BIOS. Supports APM1.2. Supports ACPI. Supports USB Function. Software Supports Warpspeeder™, 9th Touch™, WINFLASHER™ and FLASHER™. Offers the highest performance for Windows 98SE, Windows 2000, Windows Me, Windows XP, SCO UNIX etc. 1.2 PACKAGE CHECKLIST FDD Cable * 1 HDD Cable * 1 User’s Manual * 1 Serial ATA Cable * 1 Fully Setup Driver CD * 1 Rear I/O Panel for ATX Case * 1 S/PDIF Cable * 1 (optional) USB 2.
PAGE 7
915GL-M7 Ultra 1.3 MOTHERBOARD LAYOUT JCOM1 JP RNT1 JV GA1 13 1 24 12 P CI -E X BAT1 J _CI R1 (optional) JD J1 (optional) Note: ■ represents the 1st pin.
PAGE 8
915GL-M7 Ultra CHAPTER 2: HARDWARE INSTALLATION 2.1 CENTRAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ens ure pin legs won’t be damaged. pin cap Step 1: Pull the lever sideways away from the socket and then raise the lever up to a 90-degree angle. Step 2: Look for the black cut edge on socket, and the white dot on CPU should point wards this black cut edge.
PAGE 9
15GL-M7 Ultra Step 2-2: Step 3: Hold the CPU down firmly, and then close the lever to complete the installation. Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN power cable to the JCFAN1. This completes the installation. 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan wiring and plug may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.
PAGE 10
915GL-M7 Ultra wire is Ground and should be connected to GND.
PAGE 11
915GL-M7 Ultra 2.3 MEMORY MODULE INSTALLATION 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
PAGE 12
915GL-M7 Ultra 2.4 CONNECTORS AND SLOTS PCI1/PCI2: Peripheral Component Interconnect Slots This motherboard is equipped with 2 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. IDE1: Hard Disk Connectors The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~5, Bus Master, and Ultra DMA 33/ 66/ 100 functionality.
PAGE 13
915GL-M7 Ultra PCI-EX: PCI-Extreme Slot This PCI-EX (PCI-Extreme) slot is a special design for PCI-Express (PCI-E) interface graphic cards. The PCI-EX slot is compliant with PCI-Express 1.0a specification, and bandwidth of data transfer is up to 1GB/s per direction, for an aggregate of 2GB/s totally. To install the system with an add-on PCI-E graphic card, please make sure to install the driver of add-on PCI-E graphic card before onboard VGA driver installation.
PAGE 14
915GL-M7 Ultra CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.
PAGE 15
915GL-M7 Ultra JSPDIF_O UT1: Digital Audio-out Conne ctor This connector allows user to connect the PCI bracket SPDIF output header. Pin 1 2 3 1 JSPDIF_OUT1 Assignment +5V SPDIF_OUT Ground JSPDIF_IN1 (optional): Digital Audio-in Conne ctor This connector allows user to connect the PCI bracket SPDIF output header.
PAGE 16
915GL-M7 Ultra JAUDIO 2: Front Panel Audio Heade r This header allows user to connect the front audio out put cable with the PC front panel. It will disable the output on back panel audio connectors.
PAGE 17
915GL-M7 Ultra JPANEL1: Front Panel Heade r This 24-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep button, speaker and IrDA Connection. It allows user to connect the PC case’s front panel switch functions.
PAGE 18
915GL-M7 Ultra JATXPWR1/JATXPWR2: Powe r Connectors JATXPWR1: This connector allows user to connect with 20-pin power connector on the ATX power supply. JATXPWR2: By connecting this connector, it will provide +12V to CPU power circuit. 13 1 24 12 J ATXPWR1 Pin 1 2 3 4 5 6 7 8 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Pin 13 14 15 16 17 18 19 20 Assignment +3.
PAGE 19
915GL-M7 Ultra CHAPTER 4: USEFUL HELP 4.1 AWARD BIOS BEEP CODE Beep Sound One long beep followed by two short beeps High-low siren sound Meaning Video card not found or v ideo card memory bad CPU overheated System will shut down automatically One Short beep when system boot-up No error found during POST Long beeps every other second No DRAM detected or install 4.2 EXTRA INFORMATION A.
PAGE 20
915GL-M7 Ultra B. CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed.
PAGE 21
915GL-M7 Ultra 4.3 TROUBLESHOOTING Probable Solution 1. Make sure power cable is No power to the system at all securely plugged in. Power light don’t illuminate, f an inside power supply does not turn 2. Replace cable. on. 3. Contact technical support. 2. Indicator light on key board does not turn on. System inoperativ e. Keyboard lights Using even pressure on both ends of are on, power indicator lights are lit, the DIMM, press down firmly until the and hard driv e is spinning. module snaps into place.
PAGE 22
915GL-M7 Ultra CHAPTER 5: WARPSPEEDER™ 5.1 INTRODUCTION [WarpSpeeder™], a new powerful control utility, features three user-friendly functions including Overclock Manager, Overvoltage Manager, and Hardware Monitor. With the Overclock Manager, users can easily adjust the frequency they prefer or they can get the best CPU performance with just one click. The Overvoltage Manager, on the other hand, helps to power up CPU core voltage and Memory voltage.
PAGE 23
915GL-M7 Ultra 5.3 INSTALLATION 1. Execute the setup execution file, and then the following dialog will pop up. Please click “Next” button and follow the default procedure to install. 2. When you see the following dialog in setup procedure, it means setup is completed. If the “Launch the WarpSpeeder Tray Utility” checkbox is checked, the Tray Icon utility and [WarpSpeeder™] utility will be automatically and immediately launched after you click “Finish” button.
PAGE 24
915GL-M7 Ultra 5.4 [WARPSPEEDER™] INCLUDES 1 TRAY ICON AND 5 PANELS 1. Tray Icon: Whenever the Tray Icon utility is launched, it will display a little tray icon on the right side of Windows Taskbar. This utility is responsible for conveniently invoking [WarpSpeeder™] Utility. You can use the mouse by clicking the left button in order to invoke [WarpSpeeder™] directly from the little tray icon or you can right-click the little tray icon to pop up a popup menu as following figure.
PAGE 25
915GL-M7 Ultra 2. Main Panel If you click the tray icon, [WarpSpeeder™] utility will be invoked. Please refer to the following figure; the utility’s first window you will see is Main Panel. Main Panel contains fe ature s as follows: a. b. c. Display the CPU Speed, CPU external clock, Memory clock, AGP clock, and PCI clock information. Contains About, Voltage, Overclock, and Hardware Monitor Buttons for invoking respective panels.
PAGE 26
915GL-M7 Ultra 3. Voltage Panel Click the Voltage button in Main Panel, the button will be highlighted and the Voltage Panel will slide out to up as the following figure. In this panel, you can decide to increase CPU core voltage and Memory voltage or not. The default setting is “No”. If you want to get the best performance of overclocking, we recommend you click the option “Yes”.
PAGE 27
915GL-M7 Ultra 4. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel will slide out to left as the following figure. O ve rclock Panel contains the these features: a. “–3MHz button”, “-1MHz button”, “+1MHz button”, and “+3MHz button”: provide user the ability to do real-time overclock adjustment. Warning: Manually overclock is potentially dangerous, especially when the ov erclocking percentage is over 110 %.
PAGE 28
915GL-M7 Ultra c. d. “Auto-overclock button”: User can click this button and [WarpSpeeder™] will set the best and stable performance and frequency automatically. [WarpSpeeder™] utility will execute a series of testing until system fail. Then system will do fail-safe reboot by using Watchdog function. After reboot, the [WarpSpeeder™] utility will restore to the hardware default setting or load the verified best and stable frequency according to the Recovery Dialog’s setting.
PAGE 29
915GL-M7 Ultra 6. About Panel Click the “about” button in Main Panel, the button will be highlighted and the About Panel will slide out to up as the following figure. In this panel, you can get model name and detail information in hints of all the chipset that are related to overclocking. You can also get the mainboard’s BIOS model and the Version number of [WarpSpeeder™] utility.
PAGE 30
915GL-M7 Ultra Note : Because the overclock, overvoltage, and hardware monitor features are controlled by several separate chipset, [WarpSpeeder™] divide these features to separate panels. If one chipset is not on board, the correlative button in Main panel will be disabled, but will not interfere other panels’ functions. This property can make [WarpSpeeder™] utility more robust.
PAGE 31
915GL-M7 Ultra BIOS SETUP BIOS Setup........................................................................................1 1 Main Menu..................................................................................................... 3 2 Standard CMOS Features .............................................................................. 6 3 Advanced BIOS Features............................................................................... 9 4 Advanced Chipset Features................................
PAGE 32
915GL-M7 Ultra BIOS Manual BIOS Setup Introduction This manual discussed Award™ Setup program built into the ROM BIOS. The Setup program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM so that it retains the Setup information when the power is turned off. The Award BIOS™ installed in your computer system’s ROM (Read Only Memory) is a custom version of an industry standard BIOS.
PAGE 33
915GL-M7 Ultra BIOS Manual PCI Bus Support This AWARD BIOS also supports Version 2.1 of the Intel PCI (Peripheral Component Interconnect) local bus specification. DRAM Support DDR SDRAM (Double Data Rate Synchronous DRAM) are supported. Supported CPUs This AWARD BIOS supports the Intel CPU. Using Setup In general, you use the arrow keys to highlight items, press to select, use the and keys to change entries, press for help and press to quit.
PAGE 34
915GL-M7 Ultra BIOS Manual 1 Main Menu Once you enter Award BIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions. Use the arrow keys to select among the items and press to accept and enter the sub-menu. !! WARNING !! The information about BIOS defaults on manual (Figure 1,2,3,4,5,6,7,8,9) is just for reference, please refer to the BIOS installed on board, for update information. Figure 1.
PAGE 35
915GL-M7 Ultra BIOS Manual Power Management Setup This submenu allows you to configure the power management features. PnP/PCI Configurations This submenu allows you to configure certain “Plug and Play” and PCI options. PC Health Status This submenu allows you to monitor the hardware of your system. Frequency/ Voltage Control This submenu allows you to change CPU Vcore Voltage and CPU/PCI clock. (However, this function is strongly recommended not to use.
PAGE 36
915GL-M7 Ultra BIOS Manual Save & Exit Setup Save all configuration changes to CMOS (memory) and exit setup. Confirmation message will be displayed before proceeding. Exit Without Saving Abandon all changes made during the current session and exit setup. Confirmation message will be displayed before proceeding. Upgrade BIOS This submenu allows you to upgrade bios.
PAGE 37
915GL-M7 Ultra BIOS Manual 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the or keys to select the value you want in each item. Figure 2.
PAGE 38
915GL-M7 Ultra BIOS Manual Main Menu Selections This table shows the selections that you can make on the Main Menu. Item Options Date mm : dd : yy Set the system date. Note that the ‘Day’ automatically changes when you set the date. Time hh : mm : ss Set the clock. IDE Primary Master Options are in its sub menu. Press to enter the sub menu of detailed options IDE Primary Slave Options are in its sub menu. Press to enter the sub menu of detailed options.
PAGE 39
915GL-M7 Ultra BIOS Manual Item Halt On Options Description All Errors Select the situation in which No Errors you want the BIOS to stop All, but Keyboard All, but Diskette the POST process and notify you. All, but Disk/ Key Base Memory N/A Displays the amount of conventional memory detected during boot up. Extended Memory N/A Displays the amount of extended memory detected during boot up. Total Memory N/A Displays the total memory available in the system.
PAGE 40
915GL-M7 Ultra BIOS Manual 3 Advanced BIOS Features Figure 3. Advanced BIOS Setup CPU FEATURE Delay Prior to Thermal Set this item to enable the CPU Thermal function to engage after the specified time. The Choices: 4, 8, 16 (default), 32. Thermal Management Allow you to choose the thermal management method of your monitor. The Choices: Thermal Monitor 1 (default), Thermal Monitor2. Notes: The choices will be different according to your CPU features.
PAGE 41
915GL-M7 Ultra BIOS Manual TM2 Bus Ratio Represents the frequency. Bus ratio of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot. The Choices: 0X (default). TM2 Bus VID Represents the voltage of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot. The Choices: 0.8375 (default). Limit CPU ID Max Val Set limit CPU ID maximum vale to 3, it should be disabled for Win XP.
PAGE 42
915GL-M7 Ultra BIOS Manual BOOT SEQ & FLOPPY SETUP First/Second/Third/Boot Other Device These BIOS attempt to load the operating system from the device in the sequence selected in these items. The Choices: Floppy, LS120, HDD-0, SCSI, CDROM, HDD-1, HDD-2,HDD-3, ZIP100, LAN, HPT370, Disabled, Enabled. Swap Floppy Drive For systems with two floppy drives, this option allows you to swaplogical drive assignments. The Choices: Disabled (default), Enabled.
PAGE 43
915GL-M7 Ultra BIOS Manual CPU L3 Cache Depending on the CPU/chipset in use, you may be able to increase memory access time with this option. Enabled (default) Enable cache. Disabled Disable cache. HYPER-THREADING TECHNOLOGY This option allows you to enable or disabled CPU Hyper-Threading. Enabled for Windows XP and Linux 2.4.x (OS optimized for Hyper Threading Technology. Disabled for other OS (OS not optimized for Hyper Threading Technology. The Choices: Enabled (default), Disabled.
PAGE 44
915GL-M7 Ultra BIOS Manual SECURITY OPTION This option will enable only individuals with passwords to bring the system online and/or to use the CMOS Setup Utility. System A password is required for the system to boot and is also required to access the Setup Utility. Setup (default) A password is required to access the Setup Utilityonly. This will only apply if passwords are set from the Setup main menu. APIC MODE Selecting Enabled enables APIC device mode reporting from the BIOS to the operating system.
PAGE 45
915GL-M7 Ultra BIOS Manual 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system. This chipset manage bus speeds and access to system memory resources, such as DRAM. It also coordinates communications with the PCI bus. The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly. Figure 4.
PAGE 46
915GL-M7 Ultra BIOS Manual DRAM RAS# PRECHARGE If an insufficient number of cycles is allowed for RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete, and the DRAM may fail to retain data. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The Choices: Auto (default). PRECHARGE DELAY (TRAS) This item controls the number of DRAM clocks to activate the precharge delay.
PAGE 47
915GL-M7 Ultra BIOS Manual 5 Integrated Peripherals Figure 5. Integrated Peripherals OnChip IDE Device IDE HDD Block Mode Block mode is also called block transfer, multiple commands, ormultiple sector read / write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read / write per sector where the drive can support.
PAGE 48
915GL-M7 Ultra BIOS Manual IDE DMA Transfer Access This item allows you to enable or disable the IDE transfer access. The Choices: Enabled (default), Disabled. On-chip Primary PCI IDE This item allows you to enable or disable the primary/ secondary IDE Channel. The Choices: Enabled (Default), Disabled. IDE Primary/Secondary/Master/Slave PIO The IDE PIO (Programmed Input / Output) fields let you set a PIO mode (0-4) for each of the IDE devices that the onboard IDE interface supports.
PAGE 49
915GL-M7 Ultra BIOS Manual ONBOARD DEVICE PCI Express Root Port Func, PCI Express Port 1/ 2/3/4 This item allows you to select the PCI Express Port. The Choices: Auto (default), Enabled, Disabled. PCI-E Compliancy Mode This item allows you to select the PCI-E Compliancy Mode. The Choices: v1.0a (default), v1.0.
PAGE 50
915GL-M7 Ultra BIOS Manual USB Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have USB peripherals. The Choices: Enabled (default), Disabled USB 2.0 Controller This entry is to enabled/ disabled EHCI controller only. This BIOS itself may/ may not have high speed USB support. If the BIOS has high speed USB support built in, the support will automatically turn on, when high speed device were attached. The Choices: Enabled (default).
PAGE 51
915GL-M7 Ultra BIOS Manual Super IO Device If you highlight the literal “Press Enter” next to the “Super IO Device” label and then press the enter key, it will take you a submenu with the following options: Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If install and FDC or the system has no floppy drive, select Disabled in this field. The Choices: Enabled (default), Disabled.
PAGE 52
915GL-M7 Ultra BIOS Manual Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O Address. The Choices: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled. Parallel Port Mode The default value is SPP. The Choices: SPP (default) Using Parallel port as Standard Printer Port. EPP Using Parallel Port as Enhanced Parallel Port. ECP Using Parallel port as Extended Capabilities Port. ECP+EPP Using Parallel port as ECP & EPP mode.
PAGE 53
915GL-M7 Ultra BIOS Manual 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features. Figure 6. Power Management Setup ACPI & WAKE UP EVENTS ACPI Function This item displays the status of the Advanced Configuration and Power Management (ACPI). The Choices: Enabled (default), Disabled.
PAGE 54
915GL-M7 Ultra BIOS Manual ACPI Suspend Type The item allows you to select the suspend type under the ACPI operating system. The Choices: S1 (POS) (default) Power on Suspend S3 (STR) Suspend to RAM S1 & S3 POS+STR Run VGABIOS if S3 Resume Choosing Enabled will make BIOS run VGA BIOS to initialize the VGA card when system wakes up from S3 state. The system time is shortened if you disable the function, but system will need AGP driver to initialize the card.
PAGE 55
915GL-M7 Ultra BIOS Manual KB POWER ON Password Input password and press Enter to set the Keyboard power on password. Hot Key Power ON Input password and press Enter to set the Keyboard power on password. The Choices: Ctrl-F1 (default), Ctrl-F2, Ctrl-F3, Ctrl-F4, Ctrl-F5, Ctrl-F6, Ctrl-F7, Ctrl-F8, Ctrl-F9, Ctrl-F10, Ctrl-F11, and Ctrl-F12. POWER After PWR-Fail This setting specifies whether your system will reboot after a power fail or interrupts occurs. Off Leaves the computer in the power off state.
PAGE 56
915GL-M7 Ultra BIOS Manual PCI PIRQ [A-D]# You can select to enable or disable PCI PIRQ [A-D]# under this item. The Choices: Disabled (default), Enabled. Power Management This category allows you to select the type (or degree) of power saving and is directly related to the following modes: 1.HDD Power Down. 2.Suspend Mode. There are four options of Power Management, three of which have fixed mode settings Min. Power Saving Minimum power management. Suspend Mode = 1 hr. HDD Power Down = 15 min Max.
PAGE 57
915GL-M7 Ultra BIOS Manual Suspend Mode The item allows you to select the suspend type under ACPI operating system. The Choices: Disabled (default), 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30 Min, 40 Min, 1 Hour. This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer. Blank Screen This option only writes blanks to the video buffer.
PAGE 58
915GL-M7 Ultra BIOS Manual 7 PnP/PCI Configurations This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. Figure 7.
PAGE 59
915GL-M7 Ultra BIOS Manual IRQ RESOURCES This submenu will allow you to assign each system interrupt a type, depending on the type of device using the interrupt. When you press the “Press Enter” tag, you will be directed to a submenu that will allow you to configure the system interrupts. This is only configurable when “Resources Controlled By” is set to “Manual”.
PAGE 60
915GL-M7 Ultra BIOS Manual 8 PC Health Status Figure 8. PC Health Status CPU FAN Control The Choice “smart” can make your CPU FAN to reduce noise. The Choices: Always On, Smart (default). Shutdown Temperature This item allows you to set up the CPU shutdown Temperature. This item only effective under Windows 98 ACPI mode The Choices: 60O C/140OF, 65O C/149O F, 70OC/158O F, Disabled (default).
PAGE 61
915GL-M7 Ultra BIOS Manual 9 Frequency/ Voltage Control Figure 9. Frequency/ Voltage Control CPU CLOCK RATIO The Choices: 8X (default), 9X, 10X, 11X, 12X, 13X, 14 X, 15X, 16X, 17X, 18X, 19X, 20 X, 21 X, 22 X, and 23X. CPU Voltage Regulator This item allows you to select CPU Voltage Regulator The Choices: Default (default). DDR Voltage Regulator This item allows you to select DDR Voltage Regulator The Choices: Default (Default).
PAGE 62
915GL-M7 Ultra BIOS Manual Method 2: Press the key and Power button simultaneously, after that keep-on pressing the key until the power-on screen showed. This action will boot-up the system according to FSB of the processor It’s strongly recommended to set CPU Vcore and clock in default setting. If the CPU Vcore and clock are not in default setting, it may cause CPU or M/B damage.