SLIM ZERO OWNER’S MANUAL
TABLE OF CONTENTS PRODUCT INFORMATION Main Unit & Parts.......................................................4 Product Diagram........................................................5 PRODUCT INSTALLATION Pre-Installation............................................................6 Installation.....................................................................8 Water Connection....................................................12 Operation...............................................................
MAIN UNIT & PARTS PRODUCT DIAGRAM Method 1 Method 2 NOTE: There are two methods for installation. The recommended way is using the rubber expansion nuts. The second option is using the butterfly nuts. Please select the option best suited for your specific installation needs.
PRE-INSTALLATION Please make sure you read the instructions carefully and install it properly. Caution 1. 3. Example of how the bolts fit through the mounting brackets and how they are placed onto the catch plate and secured to the toilet. The water pressure limit is from 10 to 110 PSI. Please use as instructed. 2. The water shutoff valve should be near where the product is installed. Pre-Installation 1. Insert the mounting bolts into the rectangular steel mounting brackets. 6 2.
INSTALLATION First Installation Method (Recommended) 1. Completely remove the old toilet seat and lid. 8 2. Install expansion nuts. 3. Attach the catch plate. 4. Install the bidet seat. • • • Be sure to firmly press down so the top of the expansion nut is flush with the ceramic toilet surface. Attach the catch plate in the toilet seat holes. Adjust the position of mounting bolts and adjust the pieces to line up the mounting bolts to the expansion nuts. Then tighten to secure the catch plate.
INSTALLATION (CONT.) Second Installation Method 1. Remove the old toilet seat. 10 2. Attach the catch plate. • Put the catch plate over the toilet seat mounting holes. Screw on the nuts from underneath the toilet. Tighten to secure the catch plate. 3. Install the bidet seat, line up the bidet with the catch plate, you will hear the seat click into place.
WATER CONNECTION 1. Close the water supply valve. Flush the toilet. 12 2. Unscrew the water supply hose from the water tank. Place a towel below the tank to catch any dripping water. 3. Attach the T-valve to the water tank where you removed the water supply hose. Ensure the rubber gasket is properly seated within the T-valve. 4. Re-attach the water supply hose to the bottom of the T-valve.
WATER CONNECTION (CONT.) 5. Connect the bidet supply hose. • 14 Connect the bidet supply hose to the metal inlet on the side of the bidet seat. Connect the other end of the hose to the T-valve and tighten snugly. Be careful not to over-tighten. 6. Slowly open the water valve to check if there is any leakage. 7. Wipe the hoses and connectors thoroughly with a towel and carefully observe for any leaks for at least 10 minutes. • Tighten any connectors gently until leakage stops.
OPERATION NIGHT LIGHT INSTRUCTIONS Stop 1. Installing the battery • Return the lever to the upright position to turn it off. • Remove the battery pack. • • To ensure the proper polarity AA batteries must be used. • During initial installation and replacement of the batteries you must install based on the figure provided above. • During long periods of non-use, it is recommended to remove the batteries from the battery pack. Insert 4AA batteries, and put the battery pack in the control box.
NIGHT LIGHT INSTRUCTIONS (CONT.) 2. Instructions 3. Replacing the battery. Operation • • When the light turns red please replace the battery. • Press the button once, the high light is on. • When replacing the battery, press the release button on the bidet, then remove. Repeat the steps above to replace the batteries. • Press again, the low light is on. • Press a third time, the light will turn off. 18 Install the bidet onto the toilet.
CLEANING & MAINTENANCE 1. Cleaning the exterior of the bidet seat. 2. Cleaning the spray nozzles. 3. Clean the filter and regulator. 4. Remove the main body. • • • Turn off the water supply, remove the white water hose and clean the filter screen. • • Clean the regulator o-ring. 20 Using a sponge/cloth with water and/or mild soap to clean the product.
TROUBLESHOOTING Status Cause Solution Water is too low during WASH/BIDET Low water pressure of the unit. During use, turn the lever forward or backward to highest setting Low water pressure of water supply. If the water supply pressure is too low, contact your local water utility.
SPECIFICATIONS Classifications Description Model Number Slim Zero WASH water flow 0.35-1.8 L/min Feminine water flow 0.35-1.8 L/min Backflow Prevention Check valve Water Supply Direct from water pipes Water Pressure Range 10-110 PSI Dimensions 19.68” (l) x 14.30” (w) x 2.25” (h) Weight 4.
WARRANTY Your Bio Bidet Slim Zero is warranted against defects in materials or workmanship for one (1) year from the date of original purchase. Defective parts or a defective product returned to Bio Bidet will be repaired with new or comparable rebuilt parts by Bio Bidet at their sole discretion. This limited warranty given by BBC Innovation LLC covers all defects encountered in normal use of Bio Bidet Slim Zero, and does not apply in the following cases 1.
Thank You Technical Support/Customer Service 7900 S Route 31 Crystal Lake, IL 60014 T: 847.458.2334 U.S. TOLL FREE: 877.339.5214 support@biobidet.com www.biobidet.
