WR1500N 150Mbps Wireless N Router 1910020625 REV 2.1.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
National restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Bulgaria None General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.
CONTENTS Package Contents..................................................................................................................................1 Chapter 1. Introduction.......................................................................................................................2 1.1 Overview of the Router .......................................................................................................2 1.2 Conventions ............................................................
4.6.5 4.7 4.8 4.9 Wireless Statistics................................................................................................ 34 DHCP ............................................................................................................................... 34 4.7.1 DHCP Settings..................................................................................................... 34 4.7.2 DHCP Clients List ....................................................................................
4.14.8 System log ........................................................................................................... 55 4.14.9 Statistics............................................................................................................... 56 Appendix A: FAQ ................................................................................................................................ 58 Appendix B: Configuring the PC ........................................................................
WR1500N 150Mbps Wireless N Router Package Contents The following items should be found in your package: WR1500N 150Mbps Wireless N Router Power Adapter for WR1500N 150Mbps Wireless N Router Quick Installation Guide Resource CD for WR1500N 150Mbps Wireless N Router, including: This Guide Other Helpful Information Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.
WR1500N Chapter 1. 150Mbps Wireless N Router Introduction Thank you for choosing the WR1500N 150Mbps Wireless N Router. 1.1 Overview of the Router The WR1500N 150Mbps Wireless N Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP. The 150Mbps Wireless N Router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking performance.
WR1500N 150Mbps Wireless N Router Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet access. Supports Virtual Server, Special Application and DMZ host. Supports UPnP, Dynamic DNS, Static Routing. Provides Automatic-connection and Scheduled Connection on certain time to the Internet. Connects Internet on demand and disconnects from the Internet when idle for PPPoE. Built-in NAT and DHCP server supporting static IP address distributing.
WR1500N 150Mbps Wireless N Router Note: 1. After a device is successfully added to the network by WPS function, the WPS LED will keep on for about 5 minutes and then turn off. 2. When press and hold the WPS/Reset Button for more than 5 seconds, you will reset the router. 1.4.2 The Rear Panel Figure 1-2 Rear Panel sketch The following parts are located on the rear panel (View from left to right). POWER: The Power socket is where you will connect the power adapter.
WR1500N Chapter 2. 150Mbps Wireless N Router Connecting the Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet) One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is connected directly to the Ethernet.) PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors TCP/IP protocol on each PC Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari 2.
WR1500N Figure 2-1 150Mbps Wireless N Router Hardware Installation of the WR1500N 150Mbps Wireless N Router 2.3.1 Repeater Mode After finishing the steps above, please choose the operation mode you need and carry out the corresponding steps. WR1500N is used to extend the range of wireless signal of the existing AP or wireless router. On this mode, the only wired port works as LAN. Computer could connect to the device by either wired or wireless way.
WR1500N Chapter 3. 150Mbps Wireless N Router Quick Installation Guide This chapter will show you how to configure the basic functions of your WR1500N 150Mbps Wireless N Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the WR1500N 150Mbps Wireless N Router is 192.168.0.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.
WR1500N 150Mbps Wireless N Router Figure 3-2 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and the Router correct? Note: The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter should be lit. 2. Is the TCP/IP configuration for your PC correct? Note: If the Router's IP address is 192.168.0.1, your PC's IP address must be within the range of 192.168.0.2 ~ 192.168.0.254. 3.
WR1500N Figure 3-4 150Mbps Wireless N Router Login Windows Note: If the above screen does not pop-up, it means that your Web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 2. 3. After successfully log in, you can click the Quick Setup menu to quickly configure your Router.
WR1500N 4. 150Mbps Wireless N Router Make sure the cable is securely plugged into the WAN port. 1) If the connection type is PPPoE, the next screen will appear as shown in Figure 3-7. Figure 3-7 Quick Setup - PPPoE User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP. 2) If the connection type is Dynamic IP, the next screen will appear as shown in Figure 3-9.
WR1500N 150Mbps Wireless N Router Figure 3-9 Quick Setup – Wireless Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be (XXXXXX indicates the last unique six numbers of each Router’s MAC address). This value is case-sensitive.
WR1500N 150Mbps Wireless N Router No Change - If you chose this option, wireless security configuration will not change! These settings are only for basic wireless parameters. For advanced settings, please refer to Section 4.6: “Wireless”. 6. Click the Next button. You will then see the Finish page. If you don’t make any changes on the Wireless page, you will see the Finish page as shown in Figure 3-10. Click the Finish button to finish the Quick Setup.
WR1500N 150Mbps Wireless N Router Chapter 4. Configuring the Router This chapter will show each Web page's key functions and the configuration way. 4.1 Login After your successful login, you will see the thirteen main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. Figure 4-1 the main menu The detailed explanations for each Web page’s key function are listed below. 4.
WR1500N Figure 4-2 150Mbps Wireless N Router Router Status 4.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide". 4.4 WPS This section will guide you to add a new wireless device to an existing network quickly by WPS (Wifi Protected Setup) function. a) Choose menu “WPS”, you will see the next screen (shown in Figure 4-3).
WR1500N 150Mbps Wireless N Router Figure 4-3 WPS WPS Status - Enable or disable the WPS function here. Current PIN - The current value of the Router's PIN is displayed here. The default PIN of the Router can be found in the label or User Guide. Restore PIN - Restore the PIN of the Router to its default. Gen New PIN - Click this button, and then you can get a new random value for the Router's PIN. You can ensure the network security by generating a new PIN.
WR1500N 150Mbps Wireless N Router The WPS Configuration Screen of Wireless Adapter Method Two: Step 1: Press the WPS/Reset Button on the front panel of the Router. Note: When press and hold the WPS/Reset Button for more than 5 seconds, you will reset the router.
WR1500N 150Mbps Wireless N Router Step 2: For the configuration of the wireless adapter, please choose “Push the button on my access point” in the configuration utility of the WPS as below, and click Next. The WPS Configuration Screen of Wireless Adapter Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration.
WR1500N Step 2: Step 3: 150Mbps Wireless N Router Figure 4-4 Add A New Device Choose “Press the button of the new device in two minutes” and click Connect. For the configuration of the wireless adapter, please choose “Push the button on my access point” in the configuration utility of the WPS as below, and click Next. The WPS Configuration Screen of Wireless Adapter Step 4: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration.
WR1500N 150Mbps Wireless N Router The WPS Configuration Screen of Wireless Adapter II. By PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Method One: Enter the PIN into my Router Step 1: Keep the default WPS Status as Enabled and click the Add device button in Figure 4-3, then the following screen will appear.
WR1500N 150Mbps Wireless N Router The WPS Configuration Screen of Wireless Adapter Note: In this example, the default PIN code of this adapter is 16952898 as the above figure shown. Method Two: Enter the PIN from my Router Step 1: Get the Current PIN code of the Router in Figure 4-3 (each Router has its unique PIN code. Here we take the PIN code 21083242 of this Router for example).
WR1500N 150Mbps Wireless N Router Note: The default PIN code of the Router can be found in its label or the WPS configuration screen as Figure 4-3. c) You will see the following screen when the new device successfully connected to the network. Note: 1. The WPS LED on the Router will light green for five minutes if the device has been successfully added to the network. 2. The WPS function cannot be configured if the Wireless Function of the Router is disabled.
WR1500N 150Mbps Wireless N Router IP Address - Enter the IP address of your Router or reset it in dotted-decimal notation (factory default: 192.168.0.1). Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask. Note: 1. If you change the IP Address of LAN, you must use the new IP Address to log in the Router. 2.
WR1500N 150Mbps Wireless N Router Use These DNS Servers - If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP. Note: If you find error when you go to a website after entering the DNS addresses, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.
WR1500N Figure 4-9 150Mbps Wireless N Router WAN - PPPoE User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Secondary Connection - It’s available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network, then you can check the radio button of Dynamic/Static IP to activate this secondary connection.
WR1500N 150Mbps Wireless N Router mode. The Internet connection can be disconnected automatically after a specified inactivity period and re-established when you attempt to access the Internet again. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Caution: Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background.
WR1500N 150Mbps Wireless N Router Figure 4-11 MAC Address Clone Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here. WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XX-XX format (X is any hexadecimal digit).
WR1500N Figure 4-13 150Mbps Wireless N Router Wireless Settings SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be (XXXXXX indicates the last unique six numbers of each Router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the pull-down list.
WR1500N 150Mbps Wireless N Router change the wireless channel unless you notice interference problems with another nearby access point. Mode - Select the desired mode. The default setting is 11bgn mixed. 11b only - Select if all of your wireless clients are 802.11b. 11g only - Select if all of your wireless clients are 802.11g. 11n only- Select only if all of your wireless clients are 802.11n. 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients.
WR1500N 150Mbps Wireless N Router WEP Index - This option should be chosen if the key type is WEP(ASCII) or WEP(HEX).It indicates the index of the WEP key. Auth Type - This option should be chosen if the key type is WEP(ASCII) or WEP(HEX).It indicates the authorization type of the Root AP. Password - If the AP your Router is going to connect needs password, you need to fill the password in this blank. 4.6.
WR1500N 150Mbps Wireless N Router Figure 4-16 Type - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. WEP Key Format - Hexadecimal and ASCII formats are provided here. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.
WR1500N 150Mbps Wireless N Router Radius Port - Enter the port number of the Radius server. Radius Password - Enter the password for the Radius server. Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. WPA-PSK/WPA2-PSK - It’s the WPA/WPA2 authentication type based on pre-shared passphrase. If you check this radio button, the page will appear as shown in Figure 4-18.
WR1500N 150Mbps Wireless N Router Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 4-20: Figure 4-20 Add or Modify Wireless MAC Address Filtering entry To add a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field.
WR1500N 150Mbps Wireless N Router 4.6.4 Wireless Advanced Choose menu “Wireless → Wireless Advanced”, you can configure the advanced settings of your wireless network. Figure 4-21 Wireless Advanced Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100.
WR1500N 150Mbps Wireless N Router Note: If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. 4.6.5 Wireless Statistics Choose menu “Wireless → Wireless Statistics”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station.
WR1500N 150Mbps Wireless N Router Figure 4-24 DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.
WR1500N 150Mbps Wireless N Router Figure 4-25 DHCP Clients List Client Name - The name of the DHCP client MAC Address - The MAC address of the DHCP client. Assigned IP - The IP address that the Router has allocated to the DHCP client. Lease Time - The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page.
WR1500N 150Mbps Wireless N Router To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button. Click the Enable/Disabled All button to make all entries enabled/disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 4.
WR1500N 150Mbps Wireless N Router To setup a virtual server entry: 1. Click the Add New… button, the next screen will pop-up as shown in Figure 4-30. 2. Select the service port you want to use from the Common Service Port list. If the Common Service Port list does not have the service that you want to use, type the service port number or service port range in the Service Port box. 3. Type the IP Address of the computer in the IP Address box. 4.
WR1500N 150Mbps Wireless N Router Figure 4-31 Port Triggering Once the Router is configured, the operation is as follows: 1. A local host makes an outgoing connection using a destination port number defined in the Trigger Port field. 2. The Router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. 3.
WR1500N 150Mbps Wireless N Router Figure 4-32 Add or Modify a Port Triggering Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button. Click the Enable All button to make all entries enabled. Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries. Note: 1.
WR1500N 150Mbps Wireless N Router Note: After you set the DMZ host, the firewall related to the host will not work. 4.8.4 UPnP Choose menu “Forwarding → UPnP”, you can view the information about UPnP (Universal Plug and Play) in the screen as shown in Figure 4-34. The UPnP feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN.
WR1500N 150Mbps Wireless N Router Figure 4-36 Advanced Security Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics. The result of the statistics is used for analysis by SYN Flood, UDP Flood and ICMP-Flood. DoS protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function.
WR1500N 150Mbps Wireless N Router Ignore Ping Packet From WAN Port - Enable or Disable Ignore Ping Packet From WAN Port. The default setting is disabled. If enabled, the ping packet from the Internet cannot access the Router. Forbid Ping Packet From LAN Port - Enable or Disable Forbid Ping Packet From LAN Port. The default setting is disabled. If enabled, the ping packet from LAN cannot access the Router. This function can be used to defend against some viruses.
WR1500N 150Mbps Wireless N Router Figure 4-38 Static Routing To add static routing entries, follow the steps below. 1. Click Add New… shown in Figure 4-38, you will see the following screen Figure 4-39. 2. Figure 4-39 Enter the following data. Add or Modify a Static Route Entry Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route.
WR1500N 150Mbps Wireless N Router 4.11 Bandwidth Control You can configure the Bandwidth control function on this page shown in Figure 4-40: Figure 4-40 Bandwidth Control Enable IP QoS - Enable or disable the function of IP QoS. Choose BandWidth Type - Select the network connection type from the drop-down list. Bandwidth Apply - The bandwidth you get. If you are not clear about that, please contact with your ISP for help. IP Range - IP range of this entry.
WR1500N 150Mbps Wireless N Router There are two submenus under the IP &MAC Binding menu (shown in Figure 4-41): Binding Setting and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below. 4.12.1 Binding Settings This page displays the IP & MAC Binding Setting table; you can operate it in accord with your desire as shown in Figure 4-42.
WR1500N 150Mbps Wireless N Router Figure 4-44 Find IP & MAC Binding Entry Click the Enable All button to make all entries enabled. Click the Delete All button to delete all entries. 4.12.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could configure the items on the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding entries as shown in Figure 4-45.
WR1500N 150Mbps Wireless N Router 4.13 Dynamic DNS Choose menu “Dynamic DNS”, you can configure the Dynamic DNS function. The Router offers the DDNS (Dynamic Domain Name System) feature, which allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself) and a dynamic IP address, and then your friends can connect to your server by entering your domain name no matter what your IP address is.
WR1500N 150Mbps Wireless N Router 4.13.2 Oray.net DDNS If your selected dynamic DNS Service Provider is www.oray.net, the page will appear as shown in Figure 4-47. Figure 4-47 Oray.net DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Click the Login button to login the DDNS service. Connection Status - The status of the DDNS service connection is displayed here.
WR1500N 150Mbps Wireless N Router Figure 4-48 Comexe.cn DDNS settings To set up for DDNS, follow these instructions: 1. Type the domain names your dynamic DNS service provider gave. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to login to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to logout of the DDNS service. 4.
WR1500N 150Mbps Wireless N Router 4.14.1 Time Settings Choose menu “System Tools → Time Settings”, you can configure the time on the following screen. Figure 4-50 Time settings Time Zone - Select your local time zone from this pull-down list. Date - Enter your local date in MM/DD/YY into the right blanks. Time - Enter your local time in HH/MM/SS into the right blanks. To set time manually, follow the steps below: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format.
WR1500N 150Mbps Wireless N Router Figure 4-51 Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic too. Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Traceroute - This diagnostic tool tests the performance of a connection. Note: You can use ping/traceroute to test both numeric IP address or domain name.
WR1500N Figure 4-52 150Mbps Wireless N Router Diagnostic Results Note: Only one user can use this tool at one time. Options “Number of Pings”, “Ping Size” and “Ping Timeout” are used for Ping function. Option “Tracert Hops” are used for Tracert function. 4.14.3 Firmware Upgrade Choose menu “System Tools → Firmware Upgrade”, you can update the latest version of firmware for the Router on the following screen.
WR1500N 150Mbps Wireless N Router 4.14.4 Factory Defaults Choose menu “System Tools → Factory Defaults”, and you can restore the configurations of the Router to factory defaults on the following screen. Figure 4-54 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. The default User Name: admin The default Password: admin The default IP Address: 192.168.0.1 The default Subnet Mask: 255.255.255.0 Note: 1.
WR1500N 150Mbps Wireless N Router Figure 4-56 Reboot the Router Some settings of the Router will take effect only after rebooting, which include: Change the LAN IP Address (system will reboot automatically). Change the DHCP Settings. Change the Wireless configurations. Change the Web Management Port. Upgrade the firmware of the Router (system will reboot automatically). Restore the Router's settings to factory defaults (system will reboot automatically).
WR1500N 150Mbps Wireless N Router Figure 4-58 System Log The router can keep logs of all traffic. You can query the logs to find what happened to the router. Click the Refresh button to refresh the logs. Click the Clear All button to clear all the logs. 4.14.9 Statistics Choose menu “System Tools → Statistics”, you can view the network traffic of each PC on the LAN, including total traffic and the value of the last Packets Statistic interval in seconds.
WR1500N 150Mbps Wireless N Router Statistics Table: IP Address/ MAC Address Total Current The IP Address and MAC address are displayed with related statistics Packets The total number of packets received and transmitted by the Router. Bytes The total number of bytes received and transmitted by the Router. Packets The total number of packets received and transmitted in the last Packets Statistic interval seconds.
WR1500N 150Mbps Wireless N Router Appendix A: FAQ 1. How do I configure the Router to access the Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router. The telephone cord plugs into the Line port of the ADSL Modem. 3) Log in to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “PPPoE” for WAN Connection Type.
WR1500N 150Mbps Wireless N Router address is proper MAC address, click the Clone MAC Address button and your PC’s MAC address will fill in the "WAN MAC Address" field. Or else, type the MAC Address into the "WAN MAC Address" field. The format for the MAC Address is XX-XX-XX-XX-XX-XX. Then click the Save button. It will take effect after rebooting. Figure A-3 3.
WR1500N 4) How to enable DMZ Host: Log in to the Router, click the “Forwarding” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click Enable radio button and type your IP address into the “DMZ Host IP Address” field, using 192.168.0.169 as an example, remember to click the Save button. Figure A-6 4.
WR1500N Figure A-9 5. 150Mbps Wireless N Router Add or Modify a Virtual server Entry The wireless stations cannot connect to the Router. 1) Make sure the "Enable Wireless Router Radio" is checked. 2) Make sure that the wireless stations' SSID accord with the Router's SSID. 3) Make sure the wireless stations have right KEY for encryption when the Router is encrypted. 4) If the wireless connection is ready, but you can’t access the Router, check the IP Address of your wireless stations.
WR1500N 150Mbps Wireless N Router Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary. 1. Configure TCP/IP component 1) On the Windows taskbar, click the Start button, and then click Control Panel. 2) Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window.
WR1500N 150Mbps Wireless N Router Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
WR1500N 150Mbps Wireless N Router Figure B-3 Note: For Windows 98 OS or before, the PC and Router may need to be restarted. Setting IP address manually 1 Select Use the following IP address radio button. And the following items available. 2 If the Router's LAN IP address is 192.168.0.1, specify the IP address as 192.168.0.x (x is from 2 to 254), and the Subnet mask as 255.255.255.0. 3 Type the Router’s LAN IP address (the default IP is 192.168.0.1) into the Default gateway field.
WR1500N Figure B-4 Now, click OK to keep your settings.
WR1500N 150Mbps Wireless N Router Appendix C: Specifications General Standards IEEE 802.3, 802.3u, 802.11b, 802.11g Compatible with 802.
WR1500N 150Mbps Wireless N Router Appendix D: Glossary 802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.
