User guide

38
9 CLOCK AND ALARM SETTINGS
9.1 Date and Time Sengs
If you have subscribed to the Calling Line Idenficaon service, the me
and date sengs will be automacally updated by the network when you
receive an incoming call, but you may sll need to set the correct year.
You can also set the date and me manually.
1. From the home screen, press
M.
2. Press
+ or - to CLOCK&ALARM and the press M to select.
3. Press
M again to select DATE & TIME.
• The last stored date is displayed, with the third digit of the year
flashing.
4. Enter the current date and press
M to confirm.
Enter the date in the format YY/MM/DD, e.g.03 May 2014 as [1], [4],
[0], [5], [0], [3].
If you make a mistake, press
m to go back to the previous digit
entered.
5. Enter the current me and press
M to confirm. The default me
format is 24 HOURS. (To change the me format, see 9.1.1 Change
the Time Format.)
For 24-hour format, enter 1:30pm as [1], [3], [3], [0].
For 12-hour format, enter 1:30 am or pm as [0],[1],[3],[0] and then
press
+ to select am , or press - to select pm.
If you make a mistake, press
m
to go back to the previous digit
entered.
• A confirmaon tone is played.
6. Press
O
to return to standby mode.
12 ANSWERING MACHINE
Your phone includes a telephone answering machine that records
unanswered calls when it is on.
The answering machine can store up to 59 messages within the
maximum recording me of approximately 30 minutes and each message
can be up to 3 minutes long.
When the answering machine is on, calls are answered aer the set RING
DELAY.
If you have selected RECORD MSGS, then the caller can leave you a
message aer hearing your announcement.
If a new message is recorded on your answering machine, the message
indicator on the base and the answering machine icon on the handset
both flash slowly.
If you have selected ANSWER ONLY mode, the caller can only listen to
your announcement but cannot leave you a message.
If the answering machine memory is full, the answering machine LED on
the base flashes rapidly, the answering machine icon on the handset
flashes quite quickly, and the ANSWER ONLY announcement will be
played to new callers. You will have to delete some messages before any
new ones can be recorded.
12.1 Turning the Answering Machine On/Off
1. From the home screen, press
M.
2. Press
M again to select ANS. SYSTEM.
3. Press
+ or - to ANS. ON/OFF and then press M to select.
4. Press
+ or - to select ON or OFF and then press M to confirm.
• A confirmaon tone is played.
5. Press
O to return to standby mode.
Note: If the answering machine is OFF and the Master PIN is sll set at its
default 0000, the answering machine will not answer any incoming calls.
However, if the Master PIN has been changed and Remote Access is
acvated, it will answer incoming calls aer 14 rings to allow remote
access, and the ANSWER ONLY announcement will play. (See 12.8
Remote Access.)
10 PERSONAL SETTINGS
Your phone comes with a selecon of sengs that you can change to
personalise your phone to the way you like it to work.
10.1 Set the Ring Volume
You can set the handset ringer volume for external calls from Level 1 to
Level 4 or turn the ringer off. (Intercom calls always ring on a loud
volume.)
1. From the home screen, press
M.
2. Press
+ or - to HANDSET OPTS and then press M to select.
3. Press
+ or - to RINGER & TONES and then press M to select.
4. Press
M again to select RING VOLUME.
5. Press
+ or - to select the desired seng (each volume level
will play as it is selected) and then press
M
to confirm.
• A confirmaon tone is played.
6. Press
O
to return to standby mode.
Note: From standby mode, you can also press and hold the # key to
switch the ringer On and Off for external calls. The ringer off icon displays
on the screen when ringer off feature is acvated.
10.2 Set the Ring Tone
You can select from 10 ringer melodies for external calls. (Intercom calls
always ring with Melody 1.)
1. From the home screen, press
M.
2. Press
+ or - to HANDSET OPTS and then press M to select.
3. Press
+ or - to RINGER & TONES and then press M to select.
4. Press
+ or - to RING TONE and then press M to select.
5. Press
+ or - to select the desired ringer melody from 1 to 10
(each melody will play as it is selected) and then press
M to confirm.
• A confirmaon tone is played.
6. Press
O to return to standby mode.
9.1.1 Change the Time Format
The me can be displayed either as 12-hour or 24-hour. The default
seng is 24 HOUR.
1. From the home screen, press
M.
2. Press
+ or - to CLOCK&ALARM and then press M to select.
3. Press
+ or - to SET FORMAT and then press M to select.
4. Press
M again to select TIME FORMAT.
• The current seng is displayed.
5. Press
+ or - to select 12 HOUR or 24 HOUR and then press M
to confirm.
• A confirmaon tone is played.
6. Press
O
to return to standby mode.
9.1.2 Change the Date Format
The date can be displayed either as Month/Day (MM/DD) or Day/Month
(DD/MM). The default seng is DD/MM.
1. From the home screen, press
M
.
2. Press
+ or - to CLOCK&ALARM and then press M to select.
3. Press
+ or - to SET FORMAT and then press M to select.
4. Press
+ or - to DATE FORMAT and then press M to select.
• The current seng is displayed.
5. Press
+ or - to select DD/MM or MM/DD and then press M
to confirm.
• A confirmaon tone is played.
6. Press
O
to return to standby mode.
9.2 Alarm Sengs
An alarm can be set on a handset, to sound at a set me only once or
repeated each day.
When an alarm is set, the alarm icon is shown on the handset display.
When the alarm me is reached, the handset will flash -ALARM- on the
display and sound an alarm for 1 minute.
When the alarm rings, you can press any key on the handset to stop the
ringing, even if the key lock is acvated.
1. From the home screen, press
M.
2. Press
+ or - to CLOCK&ALARM and then press Mto select.
3. Press
+ or - to ALARM and then press M to select.
4. Press
+ or - to show your required alarm opon.
OFF: Turn alarm off
ONCE: The alarm sounds once at the set me.
DAILY: The alarm sounds daily at the set me.
5. Press
M to select the displayed opon.
6. If ONCE or DAILY is selected, enter the desired hour and minutes.
Press
+ to select am, or press - to select pm if the me is in
12-hour format.
7. Press
M to confirm the alarm seng.
• A confirmaon tone is played.
8. Press
O
to return to standby mode.
9.2.1 Set the Alarm Tone
You can select from 3 alarm melodies.
1. From the home screen, press
M.
2. Press
+ or - to CLOCK&ALARM and then press M to select.
3. Press
+ or - to ALARM MELODY and then press M to select.
4. Press
+ or - to select the desired alarm tone (each tone will
sound as it is selected) and then press
M
to confirm.
• A confirmaon tone is played.
5. Press
O
to return to standby mode.
10.3 Set the Key ToneThe handset emits a tone with each key press.
You can choose to turn this tone on or off. The default seng is ON.
1. From the home screen, press
M.
2. Press
+ or - to HANDSET OPTS and then press M to select.
3. Press
+ or - to RINGER & TONES and then press M to select.
4. Press
+ or - to KEY TONE and then press M to select.
5. Press
+ or - to select ON or OFF and then press M to
confirm.
• A confirmaon tone is played.
6. Press
O to return to standby mode.
10.4 Rename the Handset
You can personalise your handset by changing the name shown on the
handset in standby mode, from HANDSET to another name of up to 10
characters.
1. From the home screen, press
M.
2. Press
+ or - to HANDSET OPTS and then press M.
3. Press
M to select HANDSET NAME.
• The current handset name is displayed.
4. Press
m
to delete the leers one by one and enter the new name
(maximum 10 characters).
5. Press
M to confirm.
• A confirmaon tone is played.
6. Press
O to return to standby mode.
10.5 Set the Display Language
You can change the display language on your handset. The default seng
is ENGLISH.
1. From the home screen, press
M.
2. Press
+ or - to HANDSET OPTS and then press M to select.
3. Press
+ or - to LANGUAGE and then press M to select.
4. Press
+ or - to select your preferred language and then
press
M to confirm.
• A confirmaon tone is played.
5. Press
O to return to standby mode.
Note: Once the display language is set, the handset will switch to display
in the selected language immediately.
10.6 Set Auto Hang-up
This funcon enables you to end a call automacally by simply placing
the handset back on the base unit or charging pod. By default, the Auto
Hang-up feature is ON, but it can be turned off.
WARNING: If turned OFF, a call will not be terminated when the handset
is replaced on the base or a charger, and you may connue to be charged
for the call.
1. From the home screen, press
M.
2. Press
+ or - to HANDSET OPTS and then press M to select.
3. Press
+ or - to AUTO HANG-UP and then press M to select.
4. Press
+ or - to select ON or OFF and then press M to confirm.
• A confirmaon tone is played.
5. Press
O to return to standby mode.
12.2 Answer Mode
The phone comes with two pre-recorded announcements for the
respecve answer modes:
ANSWER ONLY and RECORD MSGS.
By default, the answer mode is RECORD MSGS, which allows a caller to
leave a message on the answering machine aer the announcement. If
changed to ANSWER ONLY mode, it does not allow callers to leave
messages on the answering machine aer the announcement.
12.3 Set Answer Mode
1. From the home screen, press
M.
2. Press
M again to select ANS. SYSTEM.
3. Press
+ or - to ANSWER MODE and then press M to select.
4. Press
+ or - to select ANSWER ONLY or RECORD MSGS and
then press
M
to confirm - a confirmaon tone is played.
12.4 Answering Machine Sengs
12.4.1 Set the Ring Delay
You can set the number of rings before the answering machine answers a
call and plays the announcement, from 2 to 7 RINGS or TOLL SAVER.
IMPORTANT: If your network voice messaging (e.g. the 1571 service) is
enabled, you must set the RING DELAY to less than 6 rings, or the
network service will answer calls before your telephone answering
machine and prevent it from recording any messages.
1. From the home screen, press
M
.
2. Press
M again to select ANS. SYSTEM.
3. Press
+ or - to ANS. SETTING and then press M.
4. Press
M to select RING DELAY.
5. Press
+ or - to select 2 RINGS – 7 RINGS or TOLL SAVER and
then press
M
to confirm - a confirmaon tone is played.
Note: If TOLL SAVER is set, the answering machine answers incoming
calls on the 5th ring if you have no new messages, or 3rd ring if you do.
If using Remote Access to check messages, if it does not answer on the
3rd ring, you have no new messages, so can hang up and save the cost of
a call.
12.4.2 Acvate/Deacvate Remote Access
1. From the home screen, press
M.
2. Press
M again to select ANS. SYSTEM.
3. Press
+ or - to ANS. SETTING and then press M to select.
4. Press
+ or - to REMOTE ACC. and then press M to select.
5. Press
+ or - to select ACTIVATE or DEACTIVATE and then
press
M to confirm - a confirmaon tone is played.
Note: If the remote control access is acvated, you can check the
messages on your answering machine when you are away from home, by
calling from another phone.
The Master PIN is used for accessing the answering machine remotely. If
your answering machine is off, the Master PIN must be changed from its
default 0000 before you can use the remote access.
12.4.3 Change the Voice Language
You may be able to select a different language for the answering
machine’s pre- recorded announcements. The default seng is ENGLISH.
1. From the home screen, press
M.
2. Press
M again to select ANS. SYSTEM.
3. Press
+ or - to ANS. SETTING and then press M to select.
4. Press
+ or - to LANGUAGE and then press M to select.
5. Press
+ or - to select your preferred language (if available)
and then press
M to confirm - a confirmaon tone is played.
12.5 Message Playback
When there are new messages on the answering machine, the tape icon
flashes on the handset screen.
1. From the home screen, press
M.
2. Press
M again to select ANS. SYSTEM.
3. Press
M again to select PLAY.
• Messages automacally play through the handset’s loudspeaker.
• Messages are played from the newest first. When all new
messages have played, the play back stops and you must start
play again to listen to old messages again.
• The display shows the message number and Date/Time of the call.
• Press
F to listen to messages through the handset earpiece.
4. During playback, press
M, then + or - for the opons:
Note: To return to the screen showing the message number and
date/me, press
m.
5. Press
O to stop playback and return to standby mode.
12.6 Delete All Messages
Note: Only old messages can be deleted. New messages must be played
before they can be deleted.
1. From the home screen, press
M.
2. Press
M again to select ANS. SYSTEM.
3. Press
+ or - to DELETE ALL and then press M to select.
• CONFIRM? is displayed.
4. Press
M again to confirm - a confirmaon tone is played.
12.7 Announcement
When the answering system answers a call, either the pre-recorded or
your own personal announcement is played to the caller.
The phone has two pre-recorded announcements for the answer modes:
ANSWER ONLY and RECORD MSGS. By default, the answer mode is
RECORD MSGS, which allows a caller to leave a message on the
answering machine aer the announcement. This can be changed to
ANSWER ONLY mode, which does not allow callers to leave messages on
the answering machine aer hearing the announcement.
12.7.1 Record a Personal Announcement
You can replace the default announcements with your own personal
ones, each of up to 2 minutes long.
1. From the home screen, press
M.
2. Press
M again to select ANS. SYSTEM.
3. Press
+ or - to ANNOUNCEMENT and then press M to select.
4. Press
+ or - to select ANSWER ONLY or RECORD MSGS and
then press
M
to confirm.
5. Press
+ or - to RECORD ANNC and then press M.
• A confirmaon tone is played and RECORDING is shown.
6. Speak into the handset and press
M again to end the recording.
• A confirmaon tone plays and ANNOUNCEMENT is shown.
12.7.2 Listen to an announcement
1. From the home screen, press
M.
2. Press
M again to select ANS. SYSTEM.
3. Press
+ or - to ANNOUNCEMENT and then press M to select.
4. Press
+ or - to select ANSWER ONLY or RECORD MSGS and
then press
M to confirm.
5. Press
M to select PLAY.
• The announcement plays through the handset speaker.
• Press
F to listen to the announcement through the earpiece.
12.7.3 Delete a Personal Announcement
If you want to return to using the default announcement, simply delete
your personal announcement.
1. From the home screen, press
M.
2. Press
M again to select ANS. SYSTEM.
3. Press
+ or - to ANNOUNCEMENT and then press M to select.
4. Press
+ or - to select ANSWER ONLY or RECORD MSGS and
then press
M
to confirm.
5. Press
+ or - to DELETE and press M to confirm.
• The default announcement plays through the speaker.
• Press
F to listen to the announcement through the earpiece.
12.8 Remote Access
The phone lets you listen to the messages on your answering machine, or
otherwise operate your answering machine by calling in to your
answering machine from another touch-tone phone.
You need to enter a remote access code (same as your Master PIN) to
access your answering machine remotely.
The remote access code is used to prevent unauthorised access of your
answering machine.
Remote Access must be enabled if you want to use this feature. (See
12.4.2 Acvate/Deacvate Remote Access.)
12.8.1 Access the Answering Machine Remotely
1. Dial your phone number from any touch-tone phone.
2. When your answering machine answers your call and starts playing
your announcement, press the
# key.
• The announcement will stop playing.
3. Enter your Master PIN code within 8 seconds using the numeric
keypad on the touch-tone phone.
Note that the answering machine will drop the call if you do not
enter the Master PIN within 8 seconds.
4. If the code is accepted, you will hear a confirmaon tone.
5. The answering machine will start playing all the messages on your
answering machine, beginning with new messages, or if there are
no recorded messages you will hear four beeps.
6. Use the keypad on the touch-tone phone to carry out the following
operaons:
When you have finished listening to your messages, simply hang up the
phone to end.
Note:
If your answering machine is off but Remote Access is acvated (See
12.4.2 Acvate/Deacvate Remote Access), the answering machine will
answer your call aer 14 rings, so that you can access it remotely, and
the ANSWER ONLY announcement will play.
If you enter an incorrect Remote Access Code, you will hear a triple-beep
error tone aer 8 digits have been detected, and you will need to enter
the code again.