BIPAC-711 C2 / 7100S ADSL Modem/Router User’s Manual
Table of Contents CHAPTER 1 ......................................................................................................................................................... 1 INTRODUCTION...................................................................................................................................................... 1 1.1 An Overview of BIPAC-711 C2 / 7100S ................................................................................................... 1 1.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3.4.3.6.3 Dynamic DNS .................................................................................................................... 40 3.4.3.6.4 NAT.................................................................................................................................... 41 3.4.3.6.5 RIP ..................................................................................................................................... 42 3.4.3.6.
Chapter 1 Introduction 1.1 An Overview of BIPAC-711 C2 / 7100S BIPAC-711 C2 / 7100S ADSL Modem/Router provides a high-speed Ethernet port and an USB (Universal Serial Bus) port (711 C2) for high-speed Internet browsing. It can support downstream transmission rates of up to 8Mbps and upstream transmission rates of up to 1024Kbps. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (G.992.1); G.lite (G992.2); G.hs (G994.1)).
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 5. One CAT-5 straight LAN cable 6. One USB cable (711 C2) 7. One power adapter 1.3 BIPAC-711 C2 / 7100S Features BIPAC-711 C2 / 7100S ADSL Modem/Router provides the following features: 2 z ADSL Multi-Mode Standard: Supports downstream transmission rates of up to 8Mbps and upstream transmission rates of up to 1024Kbps. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (G.992.1); G.lite (G992.2); G.hs (G994.1)).
Chapter 1 Introduction attack will be recorded associated with timestamp in the security logging area. More firewall features will be added continually, please visit our web site to download latest firmware. z Dynamic Host Control Protocol (DHCP) client and server: In the WAN site, the DHCP client can get an IP address from the Internet Server Provider (ISP) automatically.
Chapter 2 Using Billion ADSL Modem/Router 2.1 Cautions for Using Billion ADSL Modem/Router Important note for using the BIPAC-711 C2 / 7100S ADSL Modem/Router Warning 9 DO NOT use the BIPAC-711 C2 / 7100S in high humidity or high temperatures. 9 DO NOT use the same power source for the BIPAC- 711 C2 / 7100S as other equipment. 9 DO NOT open or repair the case yourself. If the BIPAC-711 C2 / 7100S is too hot, turn off the power immediately and have it repaired at a qualified service center.
Chapter 2 Using the ADSL Modem/Router 2.3 The Rear Ports LINE (RJ-11 connector) Connect the supplied RJ-11 cable to this port when connecting to the ADSL USB (711 C2 only) Connect the supplied USB cable to this port when connecting to the PC. Reset Press it to restore the factory default setting back LAN (RJ-45 connector) Connect the supplied LAN cable to this port when connecting to a NIC (Network Interface card) in PC or to a LAN such as an office or home network.
Chapter 3 Configuration 3.1 Before Configuration The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows 98/NT/2000/XP/Me, etc. The product provides a very easy and user-friendly interface for configuration.
Chapter 3 Installation and Configuration 2. Insert the installation CD into the CD-ROM drive. Check “Search removable media” and click “Next >”. Then, it takes seconds to search and install the software. 3. When windows titled “Hardware Installation” or “Software Installation” appears, press “Continue Anyway” to go on.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 4. Then, click “Finish”. 5. After a few moments, Windows will show the new device, USB ADSL Adapter, has been detected. Select “Install from a list or specific location”. Click “Next >”. 6. Click “Next >” when the following figure appears.
Chapter 3 Installation and Configuration 7. When windows titled “Hardware Installation” appears, press “Continue Anyway”. 8. Then, click “Finish” to end the installation. 9. After installing the driver, follow the section “3.2 Configuring the Network Properties” below to modify the network settings on your PC.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router For Windows 2000 1. When Windows tells you that the new device has been detected, click “Next >” to continue. 2. Select “Search for a suitable driver for my device”. Click “Next>”. Then, insert the installation CD into the CD-ROM drive. 3. In next window, check “CD-ROM drives” and click “Next>”.
Chapter 3 Installation and Configuration 4. Continuing through the Wizard, click the “Next >” button. 5. When window titled “Digital Signature Not Found” appears, press “Yes” to continue the installation. 6. Press “Finish”. 7. If the following window “Digital Signature Not Found” appears, press “Yes” to end the installation.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router For Windows Me 1. When Windows tells you that the new device has been detected. Select “Specify the location of the driver” and click “Next >”. 2. Insert the installation CD into the CD-ROM drive and check “Removable Media”. Click “Next>” to continue. 3. Continuing through the Wizard, click the “Next >” button.
Chapter 3 Installation and Configuration 4. Continuing through the Wizard, Windows will start copying files to your system. Then, click “Finish”. For Windows 98 1. When Windows tells you that the new device has been detected, click “Next >”. 2. In the next window, select “Search for the best driver for your device” and click “Next >”.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3. Insert the installation CD into the CD-ROM drive and check “Specify a location”. Click “Browse…” to specify the driver directory such as F:\Driver\. Click “OK” and then “Next>” to continue. 4. Continuing through the Wizard, click the “Next >” button.
Chapter 3 Installation and Configuration 5. Windows will start copying files to your system. Then, click “Finish”. 6. You will see the following screen prompting for the path of the Windows source files. Please specify a location. Click “OK”.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3.1.2 Configuring the Network Properties Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties.
Chapter 3 Installation and Configuration 4. Select Internet Protocol (TCP/IP) and click Properties 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons 6. Click OK to finish the configuration. Configuring PC in Windows 98/ME 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2.
Chapter 3 Installation and Configuration 4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button. 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click OK to finish the configuration. Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3. Select the Obtain an IP address from a DHCP server radio button and click OK. 3.2 Factory Default Settings Before configuring your, you need to know the following default settings. Web Interface: Username: admin Password: Password LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site: VPI/VCI: 0/32 Encapsulation: RFC-1483 Bridged, LLC DHCP server: DHCP server is enabled. Start IP Address: 192.168.1.
Chapter 3 Installation and Configuration 3.2.2 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port IP address 192.168.1.254 Subnet Mask 255.255.255.0 DHCP server function Enabled IP addresses for distribution to PCs 100 IP addresses continuing from 192.168.1.100 through 192.168.1.199 WAN Port Encapsulation: RFC-1483 Bridged, LLC 3.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3.4 Configuring with Web Browser Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password window prompt will appear. The default username and password are “admin” and “Password”.
Chapter 3 Installation and Configuration 3.4.1.1 Status – ADSL Status Displays the status of your ADSL connection.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3.4.1.1.1 Status – WAN Status 3.4.1.1.2 Status – ATM Status 3.4.1.2 Status – LAN Status Displays the status of your Local Area Network (LAN) connection.
Chapter 3 Installation and Configuration 3.4.1.2.1 Status -TCP Status Display the status of TCP. This screen will automatically refresh every two seconds. 3.4.1.3 Status- PPP Displays the status of your PPP connection. It will refresh every ten seconds.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3.4.1.4 Status- Learned MAC Table Aging Timeout: Enter the time period for the router to memorize MAC addresses. 3.4.1.5 Routing Table Display the current routing paths of BIPAC-711 C2 / 7100S.
Chapter 3 Installation and Configuration 3.4.1.6 System Log Display the system logs cumulated till the present time. You can trace the historical information through this function. 3.4.1.7 Security Logs Display the information of security logs. If hacker attacks your sever, he will be isolated by the firewall function and the router will record related information. Hence, you know where the hacker comes from.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3.4.2 Quick Start If you use this device to access the Internet through the ISP, this web page is enough for you to configure this router and access the Internet without a problem. Please check Chapter 3.3 (Information from the ISP), then enter the proper values into this web page, click the Apply button and then click the Save Config button to save all of the configuration parameters to FLASH.
Chapter 3 Installation and Configuration 3.4.3.1 WAN Pvc0 is set as default and then press submit. The screens below contain settings for the WAN interface toward Internet. Per VC Settings There are eight Virtual Circuits (VC) for you to set, from VC 0 to VC 7. Before you make the settings, please scroll down to the button of the page and select the item of Virtual Circuit you want to configure.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router Subnet Mask: Enter the information provided by your ISP. Default Gateway: Enter the gateway address provided by your ISP. MAC SPOOFING : The MAC Spoofing is for solving the scenario when the ISP only recognizing the specified MAC address. Service Category: Select UBR or CBR. Bandwidth: Enter the bandwidth.
Chapter 3 Installation and Configuration MTU: Maximum Transmission Unit indicates the network stack of any packet is larger than this value will be fragmented before the transmission. During the PPP negotiation, the peer of the PPP connection will indicate its MRU and will be accepted. The actual MTU of the PPP connection will be set to the smaller one of MTU and the peer’s MRU. The default value is 1492. MSS: Maximum Segment Size is the largest size of data that TCP will send in a single IP packet.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router Start Address: Enter the start address of this local IP network address pool. The pool is a piece of continuous IP address segment. The default value is 192.168.1.100. End Address: Enter the last address of this local IP network address pool that you want the DHCP server to assign IP addresses to. The default value is 192.168.1.199. With this case, the DHCP pool is from 192.168.1.100 to 192.168.1.199.
Chapter 3 Installation and Configuration 3.4.3.3.3 Upgrade To upgrade the firmware of BIPAC-711 C2 / 7100S, you should download or copy the firmware to your local environment first. Press the “Browse…” button to specify the path of the firmware file. Then, click “Upgrade” to start upgrading. When the procedure is completed, BIPAC-711 C2 / 7100S will reset automatically to make the new firmware work. 3.4.3.3.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3.4.3.3.5 Restart In case the router stops responding correctly or in some other way stops functioning, you can perform the reboot. Your setting won’t be changed. Performing the reboot, click on the Restart button. 3.4.3.4 Firewall User can decide to enable this firewall function including Packet Filter, Block Hacker Attack, and Block WAN request features for better security control or not. But be noted, it wastes network processor computation power.
Chapter 3 Installation and Configuration 3.4.3.4.1 Packet Filter Packet filtering function enables you to configure your router to check specified internal/external user (IP address) from Internet access, or you can disable specific service request (Port number) to /from Internet. This configuration program allows you to set up different filter rules up to 10 for different users based on their IP addresses or their network Port number.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router If the DHCP server option is enabled, you have to be very careful in assigning the IP addresses of filtered private IP range in order to avoid conflicts because you do not know which PC in LAN is assigned to which IP address. The easiest and safest way is that the filtered IP address is assigned to specific PC that is not allowed to access outside resource such as Internet.
Chapter 3 Installation and Configuration - Smurf Attack (ICMP Echo with x.x.x.0 or x.x.x.255) - Snork Attack - UDP port loop-back - TCP NULL scan 3.4.3.4.4 Block WAN Request Check “Enable” if you want to exclude outside PING request from reaching on this router.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3.4.3.4.5 URL Blocking URL blocking function enables you to avoid your LAN PCs from accessing some URLs. You must check the “Enable” radio button to make the following figure appear for further configuration. Always Blcok: Check this will block all browsing requests from PCs Block: to specify the the time period when you want this function activated. But be noted that SNTP (Time Zone) function must WORK.
Chapter 3 Installation and Configuration For example, if you set the Public Port number 21 (FTP) to be mapped to the IP Address 192.168.1.100, then all the ftp requests from outside users will be forwarded to the local server with IP address of 192.168.1.100. Port (from) & Port (To): Enter the public port number & range you want to configure. Port Type: Select TCP if you want to scope for the connection-based application service on the remote server using the port number.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router 3.4.3.6.2 DNS A Domain Name System (DNS) contains a mapping table for domain name and IP address. In the Internet, every host has a unique and friendly name such as www.yahoo.com and IP address. The IP address is so hard to remember that you may just enter the friendly name www.yahoo.com and then the DNS will convert it to its equivalent IP address. You can obtain Domain Name System (DNS) IP address automatically if ISP provides it when you logon.
Chapter 3 Installation and Configuration 3.4.3.6.4 NAT The NAT Configuration page allows the user to set the configuration for the Network Address Translation. Dynamic NAPT: It provides dynamic Network Address Translation capability between LAN and multiple WAN connections, and the LAN traffic is routed to appropriate WAN connections based-on the destination IP addresses and Rout Table.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router Interface: This field allows the user to choose specific WAN interface (PVC or PPP Session) for NAT session. NAT allows only one entry (User IP) per session, NAPT allows many entries (User IPs) per session. Select Add or Delete and then press the Submit button to add or delete any NAT session name setting to/from the following table. Go back to the previous page, NAT Configuration, to continue further settings. 3.4.3.6.5 RIP RIP: Default at Disabled.
Chapter 3 Installation and Configuration 3.4.3.6.6 SNMP (7100S only) Simple Network Management Protocol (SNMP) is an optional feature that may or may not be supported by your ADSL Bridge/Router. SNMP is an application layer protocol that is used for managing networks. SNMP is an optional feature that may or may not be in the specific firmware that you are working with.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router Add: Click this button to add a new static routing. When you click this button, the next figure appears. Edit: Check the item you want to edit. Then, click the “Edit” button. Delete: Check the item you want to delete. Then, click the “Delete” button. Destination Subnet / Dest. Subnet Mask / Gateway Address: Fill in these fields required by this Static Routing function. 3.4.3.6.8 MISC Configuration WAN side HTTP server: Default at Disabled.
Chapter 3 Installation and Configuration DMZ, DMZ Host IP: Enable this and specify the DMZ Host IP to access any incoming request packets from WAN site. DHCP realy/DHCP Target IP: Enable this and specify the DHCP server IP address for DHCP relay function. ICMP Proxy: Enable/Disable the IGMP proxy function. PPP Auto Reconnection: To enable this function to re-establish the PPP connection again after there was a timeout causing PPP connection is terminated.
Billion BIPAC-711 C2 / 7100S ADSL Modem/Router If this test returns FAIL, please try the test again a few minutes after this test is completed. Since your DSL modem need a couple of seconds to a few minutes to establish the DSL connection depending on your phone line quality. If this test returns FAIL, make sure your phone line is connected to your DSL modem securely, and also check with your service provider to see if your service is activated. If this test returns FAIL, all other tests will be skipped.
Chapter 3 Installation and Configuration If this test returns FAIL, run this test again a few minutes after this test is completed. If this test returns FAIL consistently and DHCP client is turned on in your DSL modem, check with your service provider. If this test returns FAIL consistently and your DSL modem is statically assigned an IP address, make sure the IP address is the correct one assigned by your service provider. This test returns SKIPPED if “Ethernet connect to AAL5” test does not return PASS.
Chapter 4 Troubleshooting If the ADSL Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems Starting Up the ADSL Router Problem None of the LEDs are on when you turn on the ADSL Router. Corrective Action Check the connection between the adapter and the ADSL Router.
APPENDIX A Product Support Most problems can be solved by referring to the Troubleshooting section of this manual. If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer where you purchased this product. For further assistances with the product, please feel free to contact and visit us at http://www.billion.com.au.
