BiPAC 5200S RC Series ADSL2+ Modem / Router User Manual Version released: 2.12.17.0(UE2.C3)3.12.17.
Table of Contents Chapter 1 ............................................................................................................................1 1.1 Introducing the BiPAC 5200S RC Series ................................................................1 1.2 Features of the BiPAC 5200S RC Series ................................................................3 1.3 Application for the BiPAC 5200S RC Series...........................................................5 1.3.1 BiPAC 5210S RC ...............
4.2 Interface Setup .......................................................................................................37 4.2.1 Internet .............................................................................................................38 4.2.2 LAN ...................................................................................................................42 4.3 Advanced Setup .....................................................................................................44 4.3.
Chapter 1 Introduction the BiPAC 5200S RC Series 1.1 Introducing the BiPAC 5200S RC Series Welcome to the Billion BiPAC 5200S RC Series ADSL2+ Modem/Router. Your Billion router is an “all-in-one” unit, combining an ADSL modem, ADSL router and Ethernet network router, providing everything you need to get the machines on your network connected to the Internet over your ADSL broadband connection.
your machine on the network. Second, it can block and redirect certain ports to limit the services that outside users can access. For example, to ensure that games and other Internet applications run properly, user can open some specific ports for outside users to access the internal services of the network. Integrated DHCP (Dynamic Host Control Protocol) services, client and server allow multiple users to get their IP addresses automatically from the product on a boot up.
1.2 Features of the BiPAC 5200S RC Series ADSL Multi-Mode Standard Support downstream rate of up to 24 Mbps and upstream rate of up to 1 Mbps. It also supports rate management that allows ADSL subscribers to select an Internet access speed that suits their needs and budgets. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt(G.992.1); G.lite(G992.2)), G.hs (G994.1), G.dmt.bis (G.992.3), G.dmt.bisplus (G.992.5)). The Annex A and B are supported in different H/W platforms.
Provide an easy way to map the domain name (a friendly name for users such as www.yahoo.com) and IP address. When a local machine sets its DNS server with this router IP address, every DNS conversion request packet from the PC to this router will be forwarded to the real DNS of the outside network. Dynamic Domain Name System (DDNS) The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic IP address is the WAN IP address.
1.3 Application for the BiPAC 5200S RC Series 1.3.1 BiPAC 5210S RC 1.3.
1.3.
Chapter 2 Installing the BiPAC 5200S RC Series 2.1 Important note for using the BiPAC 5200S RC Series Warning 9 Do not use the BiPAC 5200S RC Series device in high humidity or high temperatures. 9 Do not use the same power source for the BiPAC 5200S RC Series as other equipment. 9 Do not open or repair the case yourself. If the BiPAC 5200S RC device is too hot, turn off the power immediately and have it repaired at a qualified service center. Avoid using this product and all accessories outdoors.
2.
2.3 Hardware Overview 2.3.1 BiPAC 5210S RC Front LEDs LED Meaning Lit red when power is ON. Lit green when the system is ready. Lit when connected to an Ethernet device. Lit green for both 10M and 100M. Blinking when data is Transmitted / Received. 1 Power 2 Ethernet 3 USB Lit green when the router is connected to a USB device. Flash when data is received / transmitted. 4 DSL Lit green steadily when successfully connected to an ADSL DSLAM (“linesync”).
Rear Panel Port Meaning 1 DSL Connect the supplied RJ-11 (“telephone”) cable to this port when connecting to the ADSL/telephone network. 2 USB Connect the USB cable to this port. Connect to a UTP Ethernet cable (Cat-5 or Cat-5e) to the Ethernet port when connecting to a PC or an office/home network of 10Mbps or 100Mbps. After the device is powered on, press it to reset the device or restore to factory default settings.
2.3.2 BiPAC 5200S RC / BiPAC 5200S RD Front LEDs LED 1 Power 2 Ethernet 3 DSL 4 Internet Meaning Lit red when power is ON. Lit green when the system is ready. Lit when connected to an Ethernet device. Lit green for both 10M and 100M. Blinking when data is Transmitted / Received. Lit green steadily when successfully connected to an ADSL DSLAM (“linesync”). Lit red when WAN fails to get IP address. Lit green when WAN gets the IP address.
Rear Panel Port Meaning Connect the supplied RJ-11 (“telephone”) cable to this port when connecting to the ADSL/telephone network. Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to the Ethernet port when connecting to a PC or an office/home network of 10Mbps or 100Mbps. After the device is powered on, press it to reset the device or restore to factory default settings. 1-3 seconds: reset the device 6 seconds above: restore to factory default settings (this is used when you cannot login to the router, e.g.
2.4 Cabling One of the most common problems is due to bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front panel of the product is a row of LEDs. Verify that the LAN Links and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the same telephone line as your Billion router (e.g.
Chapter 3 Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Windows 7/98 / NT / 2000 / XP /Me/Vista, MAC, Linux, etc. The product provides a very easy and user-friendly interface for configuration. 3.1 Before Configuration PCs must have an Ethernet interface installed properly and be connected either to the router directly or through an external repeater hub.
3.1.1 Configuring PC in Windows 7 1. Go to Start. Click on Control Panel. 2. Then click on Network and Internet. 3. When the Network and Sharing Center window pops up, select and click on Change adapter settings on the left window panel. 4. Select the Local Area Connection, and right click the icon to select Properties.
5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 6. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 7. Click OK again in the Local Area Connection Properties window to apply the new configuration.
3.1.2 Configuring PC in Windows Vista 1. 2. Go to Start. Click on Network. Then click on Network and Sharing Center at the top bar. 3. When the Network and Sharing Center window pops up, select and click on Manage network connections on the left window column. 4. Select the Local Area Connection, and right click the icon to select Properties.
5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 6. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. Click OK again in the Local Area Connection Properties window to apply the new configuration. 7.
3.1.3 Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
3.1.4 Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
3.1.5 Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3. Select the Obtain an IP address automatically radio button. 4. Then select the DNS Configuration tab. 5. Select the Disable DNS radio button and click OK to finish the configuration.
3.1.6 Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK.
3.2 Step-by-Step Installation 1. 2. 3. Insert the CD-ROM into CD-ROM drive Execute Windows Utility The Welcome screen will appear, click Next 4. The Hardware Installation screen will appear. Four links are shown on the screen. Click them one by one and follow the guidelines to complete hardware installation. 4.
4.2 LAN connection 4.3 DSL Line connection 4.
4.5 Filter connection 4.
5. When finished the Hardware Installation, click “Next” to proceed to next step, Network Card Selection. 6. Diagnostic screen. (If connection fails, the screen will show “FAIL”, please check your router if it is connected correctly.) 7. Click Next to enter Configuration Details 8. Set up more detailed settings such as VPI, VCI and MTU.
9. Please enter “Username” and “Password” as supplied by your ISP (Internet Service Provider) and click next. 10. Please configure the Wireless LAN setting and click next. (If your router does not support wireless, please ignore this screen and it will not appear.) 11. Click Next to proceed to Diagnostic screen 12. Congratulations!! You’ve completed the setup procedure and are ready to surf the Internet.
13. The IE browser will open up automatically when you finish installing.
3.3 Factory Default Settings Before configuring your router, you need to know the following default settings. Web Interface Username: admin Password: admin LAN Device IP Settings IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site PPPoE DHCP server DHCP server is enabled. Start IP Address: 192.168.1.100 IP pool counts: 100 3.3.1 Username and Password The default username and password are “admin” and “admin” respectively.
3.4 LAN and WAN Port Addresses The parameters of LAN and WAN ports are preset in the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 The PPPoE function is enabled to automatically get the WAN port configuration from the ISP. Subnet Mask 255.255.255.0 DHCP server function Enabled IP addresses for distribution to PCs 100 IP addresses continuing from 192.168.1.100 through 192.168.1.199 3.
3.6 Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password prompt window will appear. The default username and password are “admin” and “admin” respectively.
Chapter 4 Configuration At the configuration homepage, the top navigation pane where bookmarks are provided links to lead you directly to the desired setup page, including: Quick Start (Wizard Setup) Interface Setup (Internet, LAN) Advanced Setup (Firewall, Routing, NAT, ADSL) Access Management (ACL, Filter, SNMP, UPnP, DDNS) Maintenance (Administration, Time Zone, Firmware, SysRestart, Diagnositics) Status (Device Info, System Log, Statistics) Help Please see the relevant sections of this manual for deta
4.1 Quick Start For detailed instructions on configuring WAN settings, see the Interface Setup section of this manual. The Quick Start Wizard is a useful and easy utility to help setup the device to connect to your ISP (Internet Service Provider) with only a few steps required. It will guide you step by step to configure the password, time zone, and WAN settings of your device. The Quick Start Wizard is a helpful guide for first time users to the device.
Step1. Set your new password. Step2: Choose your time zone.
Step3: Set your Internet connection.
Step4: Save settings of this ADSL Router.
4.2 Interface Setup Click this item to access the following sub-items to configure the ADSL2+ router: Internet and LAN. These functions are described in the following sections.
4.2.
ATM VC ATM settings are used to connect to your ISP. Your ISP provides VPI, VCI settings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You need to activate the VC to take effect. For PVCs management, you can use ATM QoS to setup each PVC traffic line's priority. Virtual Circuit: VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit.
Encapsulation: ISP: Select the encapsulation type your ISP uses from the Encapsulation list. Choices vary depending on what you select in the Mode field. Dynamic IP: Select this option if your ISP provides you an IP address automatically. This option is typically used for Cable services. Please enter the Dynamic IP information accordingly. Static IP: Select this option to set static IP information.
Get IP Address: Choose Static or Dynamic for the type of IP address you want to get. Static IP Address: Enter the IP address of ADSL Router in dotted decimal notation, for example, xx.xx.xx.xx. IP Subnet Mask: The default is 0.0.0.0. User can change it to other such as 255.255.255.0.Type the subnet mask assigned to you by your ISP (if given). Gateway: You must specify a gateway IP address (supplied by your ISP) when you use 1483 Bridged IP in the Encapsulation field in the previous screen.
4.2.2 LAN A Local Area Network (LAN) is a shared communication system to which many computers are attached and is limited to the immediate area, usually the same building or floor of a building. Router Local IP IP Address: Enter the IP address of ADSL Router in dotted decimal notation, for example, 192.168.1.254 (factory default). IP Subnet Mask: The default is 255.255.255.0. User can change it to other such as 255.255.255.128. Dynamic Route: Select the RIP version from RIP-1, RIP-2B and RIP-2M.
Enable IGMP Snoop function. DHCP DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients to obtain TCP/IP configuration at start-up from a server. DHCP: If set to Enable, your device can assign IP addresses, an IP default gateway and DNS servers to Windows 95, Windows NT and other systems that support the DHCP client. If set to disabled, the DHCP server will be disabled.
4.3 Advanced Setup 4.3.1 Firewall Your router includes a firewall for controlling Internet access from your LAN and helping to prevent attacks from hackers. In addition to this, when using NAT (Network Address Translation) the router acts as a “natural” Internet firewall, since all PCs on your LAN use private IP addresses that cannot be directly accessed from the Internet.
4.3.2 Routing If you have another router with a LAN-to-LAN connection, you may create a static routing on the router that is the gateway to Internet. #: Item number. Dest IP: IP address of the destination network. Mask: The destination mask address. Gateway IP: IP address of the gateway or existing interface that this route uses. Metric: It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15.
ADD Route Destination IP Address: This is the destination subnet IP address. IP Subnet Mask: A subnet mask allows IP networks to be subdivided for security and performance purposes. Gateway IP Address: This is the gateway IP address to which packets are to be forwarded. Metric: It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15.
4.3.3 NAT The NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet. The default setting is Dynamic NAPT. It provides dynamic Network Address Translation capability between LAN and multiple WAN connections, and the LAN traffic is routed to the appropriate WAN connections based on the destination IP addresses and Route Table. This eliminates the need for static NAT session configuration between multiple LAN clients and multiple WAN connections.
DMZ The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packets which do not use a port number that is being used by any other Virtual Server entries will first be checked by the Firewall and NAT algorithms before they are passed to the DMZ host. DMZ: indicate the related LAN PC and PVC ports which allow outside network to connect in and communicate. ~ Disabled: As set in default setting, it disables the DMZ function.
connection attempts using specific ports to the PC on your network running the application. You will also need to use port forwarding if you want to host an online game server. The reason for this is that when using NAT, your publicly accessible IP address will be used by and point to your router, which then needs to deliver all traffic to the private IP addresses used by your PCs. Please see the WAN configuration section of this manual for more information on NAT.
Rule Index: Choose the rule number. Application: Choose the predefined rule from Application drop-down menu or enter a custom name. Protocol: Choose the Protocol Type, ALL, TCP or UDP. Start Port Number: Enter a port number as the beginning number of the range which you want to give to devices to access in this field. End Port Number: Enter a port number as the end number of the range which you want to give to devices to access in this field. Local IP Address: Enter your server IP address in this field.
ALG Switch In the context of computer networking, an application-level gateway (also known as ALG or application layer gateway) consists of a security component that augments a firewall or NAT employed in a computer network. It allows customized NAT traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, BitTorrent, SIP, RTSP, file transfer in IM applications etc.
IP Address Mapping Rule Index: Choose the rule number. Rule Type: One-to-one: This is the mode that maps one local IP address to one global IP address. Note that port numbers do not change for the One-to-one NAT mapping type. Many-to-One: This is the mode that maps multiple local IP addresses to one global IP address. This is equivalent to Many to One (i.e., PAT, port address translation). Many-to-Many Overload: This is mode that maps multiple local IP addresses to shared global IP addresses.
addresses, then enter 0.0.0.0 as the Local Start IP address and 255.255.255.255 as the Local End IP address. This field is N/A for One-to-one and Server mapping types. Public Start IP: This is the starting Inside Public IP Address. Enter 0.0.0.0 here if you have a dynamic IP address from your ISP. Public End IP: This is the ending Inside Public IP Address. This field is N/A for One-to-one, Many-to-One and Server mapping types.
4.3.4 ADSL ADSL Mode: The default setting is Auto Sync-UP. This mode will automatically detect your ADSL, ADSL2+, ADSL2, G.dmt, G.lite, and T1.413. But in some areas, multimode cannot detect the ADSL line code well. If it is the case, please adjust the ADSL line code to G.dmt or T1.413 first. If it still fails, please try the other values such as ALCTL, ADI, etc.
4.4 Access Management 4.4.1 ACL Access Control Listing allows you to determine which services/protocols can access BiPAC 5200S RC Series interface and from which computer. ACL: Select whether to activate to configure this ACL function. If you select Deactivated, then the following is not available. ACL Rule Index: This is item number. Active: Select Yes to active the ACL rule or No to disable ACL rule. Secure IP Address: The default 0.0.0.
4.4.2 Filter You can filter the packages by IP port, MAC and Application. Filter Type Filter Type Selection: There are three types of filter: “IP/MAC Filter”, “Application Filter”, and “URL Filter” that user can select for this connection.
Interface: Select which channel (PVC) to configure. Direction: Select the access to the Internet (“Outgoing”) or from the Internet (“Incoming”) or Both. IP/MAC Filter Rule Editing IP/MAC Filter Rule Index: This is item number Rule Type: Choose “IP” or “MAC” rules Active: Select Yes from the drop down list box to enable IP filter rule. Source IP Address: The source IP address or range of packets to be monitored.
Application Filter Application Filter: Select this option to Activated/Deactivated the Application filter. ICQ: Select this option to Allow/Deny ICQ. MSN: Select this option to Allow/Deny MSN. YMSG: Select this option to Allow/Deny Yahoo messenger. Real Audio/Video: Select this option to Allow/Deny Real Audio/Video.
URL Filter Active: Select Active to enable URL Filter. URL Index: This is item number. URL: Allow you to prevent users on your network from accessing particular websites by their URL.
4.4.3 SNMP Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. BiPAC 5200S RC Series supports SNMP agent functionality that allows a manager station to manage and monitor the router through the network. Get Community: Type the Get Community, which is the password for the incoming Get-and GetNext requests from the management station.
4.4.4 UPnP UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP offers many advantages for users running NAT routers through UPnP NAT Traversal, and on supported systems makes tasks such as port forwarding much easier by letting the application control the required settings, removing the need for user to control advanced configuration of their device.
4.4.5 DDNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is especially useful for hosting servers via your ADSL connection, so that anyone wishing to connect to you may use your domain name, rather than having to use your dynamic IP address, which changes from time to time. This dynamic IP address is the WAN IP address of the router, which is assigned to you by your ISP.
4.5 Maintenance 4.5.1 Administration In factory setting, the default password is admin, and that for user is also admin. You can change the default password to ensure that someone cannot adjust your settings without your permission. Every time you change your password, please record the password and keep it at a safe place. New Password: Type the new password in this field Confirm Password: Type the new password again in this field.
4.5.2 Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network. Choose your local time zone. After a successful connection to the Internet, the router will retrieve the correct local time from the SNTP server you have specified. If you prefer to specify an SNTP server other than those in the drop-down list, simply enter its IP address as shown above.
4.5.3 Firmware Your router’s “firmware” is the software that allows it to operate and provides all its functionality. Think of your router as a dedicated computer, and the firmware as the software it runs. Over time this software may be improved and modified, and your router allows you to upgrade the software it runs to take advantage of these changes. To upgrade the firmware of BiPAC 5200S RC Series, you should download or copy the firmware to your local environment first.
If the upload was not successful, the following screen will appear. Click Back to go back to the Firmware screen. 4.5.4 SysRestart Click SysRestart with option Current Settings to reboot your router (and restore your last saved configuration). If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings.
4.5.5 Diagnostics The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides.
4.6 Status 4.6.1 Device Info This page displays the current information for the ADSL Router. It will display the Firmware version, LAN, WAN, and MAC address information. Device Information Firmware version: This is the Firmware version. MAC Address: This is the MAC Address.
LAN IP Address: LAN port IP address. Sub Net Mask: LAN port IP subnet mask. DHCP Server: LAN port DHCP role - Enabled, Relay or disabled. WAN Virtual Circuit: There are eight groups of PVC that can be defined. VPI: The valid range for the VPI is from 0 to 255 VCI: The valid range for the VCI is from 1 to 65535 Status: “Not connected” or “Connected” Connection Type: Name of the WAN connection. IP Address: WAN port IP address. Subnet mask: WAN port IP subnet mask.
4.6.2 System Log Display system logs accumulated up to the present time. You can trace historical information with this function.
4.6.3 Statistics Read-only information here includes port status and packet specific statistics. Also provided are "Transmit Statistics" and "Receive Statistics". Ethernet Interface: This field displays the type of port. Transmit Frames: This field displays the number of frames transmitted in the last second. Transmit Multicast Frames: This field displays the number of multicast frames transmitted in the last second.
ADSL Transmit total PDUs: This field displays the number of total PDU transmitted in the last second. Transmit total Error Counts: This field displays the number of total error transmitted in the last second. Receive total PDUs: This field displays the number of total PDU received in the last second. Receive total Error Counts: This field displays the number of total error received in the last second.
4.7 Help This help page provides you some useful messages such as the introductions of some concepts and some guide. When some problems are encountered, you can turn to this page for help. For example, if you don’t understand what is Quick Start, you can go to this page, click on Quick Start, then you’ll see some messages about it, and understand it quickly. This function provides you an easy way to help yourself.
Chapter 5 Troubleshooting If the ADSL2+ Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems starting up the router Problem Corrective Action None of the LEDs Check the connection between the adapter and the router. If the are on when you error persists, you may have a hardware problem.
Problems with the WAN Interface Problem Corrective Action Initialization of the Ensure that the telephone cable is connected properly from the PVC connection ADSL port to the wall jack. The ADSL LED on the front panel of (“linesync”) failed. the router should be on. Check that VPI, VCI, encapsulation type and type of multiplexing settings are the same as those provided by your ISP. Reboot the router GE. If you still have problems, you may need to verify these settings with your ISP.
APPENDIX Product Support and Contact Information Please refer to the suggested solutions provided in the Troubleshooting section of the User Manual to solve the problems you have encountered. If you cannot find solutions to your problems from the Troubleshooting section of the manual, please contact the dealer where you purchased this product for assistance. Contact Billion WORLDWIDE http://www.billion.com MAC OS is a registered Trademark of Apple Computer, Inc.
