BiPAC 5200N 802.11n ADSL2+ Firewall Router User Manual Version Released: 2.11.100.0(NRE0.C2)3.12.1.
Table of Content Chapter 1 .............................................................................................................................1 1.1 Introducing the BiPAC 5200N ................................................................................1 1.2 Features of the BiPAC 5200N ....................................................................................3 1.3 Applications for the BiPAC 5200N ..............................................................................
4.3.1 Firewall ..............................................................................................................51 4.3.2 Routing ..............................................................................................................52 4.3.3 NAT....................................................................................................................54 4.3.4 QoS ...................................................................................................................
Chapter 1 Introduction the BiPAC 5200N 1.1 Introducing the BiPAC 5200N Welcome to the Billion BiPAC 5200N ADSL2+ Modem/Router. Your Billion router is an “all-in-one” unit, combining an ADSL modem, ADSL router and Ethernet network switch, providing everything you need to get the machines on your network connected to the Internet over your ADSL broadband connection.
product and then incoming requests for HTML that are received by the product can be rerouted to the dedicated local web server, even though the server now has a different IP address. In this example, the product is on the Internet and vulnerable to attacks, but the server is protected. Virtual Server can also be used to re-task services to multiple servers.
1.2 Features of the BiPAC 5200N ADSL Multi-Mode Standard Supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It also supports rate management that allows ADSL subscribers to select an Internet access speed suiting their needs and budgets. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt(G.992.1); G.lite(G992.2)), G.hs (G994.1), G.dmt.bis (G.992.3), G.dmt.bisplus (G.992.5)). The Annex A and B are supported in different H/W platforms. 802.
network. Dynamic Domain Name System (DDNS) The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic IP address is the WAN IP address. For example, to use the service, you must first apply for an account from a DDNS service like http://www.dyndns.org/. PPP over Ethernet (PPPoE) Provides embedded PPPoE client function to establish a connection.
1.
Chapter 2 Installing the BiPAC 5200N 2.1 Important note for using the BiPAC 5200N 9 Do not use the BiPAC 5200N in high humidity or high temperatures. 9 Do not use the same power source for the BiPAC 5200N as other equipment. 9 9 Do not open or repair the case yourself. If the BiPAC 5200N is too hot, turn off the power immediately and have it repaired at a qualified service center. Avoid using this product and all accessories outdoors. 9 Place the BiPAC 5200N on a stable surface.
2.2 Package Contents BiPAC 5200N ADSL2+ Router CD-ROM containing the online manual RJ-11 ADSL/telephone Cable (1.8M) Ethernet (CAT-5 LAN) Cable (1.
2.3 The Front LEDs BiPAC 5200N LED Meaning 1 Internet Lit red when WAN port fails to get IP address. Lit green when WAN port gets IP address successfully. 2 DSL Lit when successfully connected to an ADSL DSLAM (“linesync”). 3 WPS LED flashes green when WPS is in progress. When WPS is established the LED will lit up brightly and then goes off in 5 seconds. When WPS connection is not established, the LED will flash for 2 mins and then goes off.
2.4 The Rear Ports BiPAC 5200N Port Meaning Power Connect the supplied power adapter to this jack. 2 RESET After the device is powered on, press it to reset the device or restore to factory default settings. 0-3 seconds: reset the device 6 seconds above: restore to factory default settings (this is used when you can not login to the router, e.g.
2.5 Antenna Position Placement To get the best quality wireless reception out of your router, the antennas should be positioned like the following image to minimize the wireless interference caused between the antennas.
2.6 Cabling One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the same telephone line as your Billion router (e.g.
Chapter 3 Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Windows 98/NT/2000/XP/Me, MAC, Linux, etc. The product provides a very easy and user-friendly interface for configuration. 3.
3.1.1 Configuring PC in windows 7 1. Go to Start. Click on Control Panel. Then click on Network and Internet. 2. When the Network and Sharing Center window pops up, select and click on Change adapter settings on the left window panel. 3. Select the Local Area Connection, and right click the icon to select Properties.
4. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 5. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 6. Click OK again in the Local Area Connection Properties window to apply the new configuration.
3.1.2 Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
3.1.3 Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
3.1.4 Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3. Select the Obtain an IP address automatically radio button. 4. Then select the DNS Configuration tab. 5. Select the Disable DNS radio button and click OK to finish the configuration.
3.1.5 Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK.
3.2 Step-by-Step Installation 1. 2. 3. Insert the CD-ROM into CD-ROM drive Execute Windows Utility The Welcome screen will appear, click Next 4. The Hardware Installation screen will appear. Four links are shown on the screen. Click them one by one and follow the guidelines to complete hardware installation. 4.1 Power connection 4.
4.3 ADSL Line connection 4.4 Filter connection 5. When finished Hardware Installation, click “Next” to proceed to next step, Network Card Selection. 6. Diagnostic screen. (If connection fails, the screen will show “FAIL” ,please check your router is connected correctly.) 7. Click Next to enter Configuration Details 8. Set up more detailed settings such as VPI, VCI and MTU.
9. Please enter “Username” and “Password” as supplied by your ISP (Internet Service Provider) and click next. 10. Please configure the Wireless LAN setting and click next. (If your router does not support wireless, please ignore this screen and it will not appear.) 11. Click Next to proceed to Diagnostic screen 12. Congratulations!! You’ve completed the setup procedure and are ready for surfing the Internet.
13. The IE browser will be opened automatically when you finish installing.
3.3 Factory Default Settings Before configuring your router, you need to know the following default settings. Web Interface: Username: admin Password: admin LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site: PPPoE DHCP server: DHCP server is enabled. Start IP Address: 192.168.1.100 IP pool counts: 100 3.3.1 Username and Password The default username and password are “admin” and “admin” respectively.
3.4 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 Subnet Mask 255.255.255.0 DHCP server function Enabled IP addresses for distribution to PCs 100 IP addresses continuing from 192.168.1.100 through 192.168.1.199 The PPPoE function is enabled to automatically get the WAN port configuration from the ISP. 3.
3.6 Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password window prompt will appear. The default username and password are “admin” and “admin”.
Chapter 4 Configuration At the configuration homepage, the top navigation pane where bookmarks are provided links you directly to the desired setup page, including: Quick Start (wizard setup) Interface Setup (Internet, LAN, Wireless) Advanced Setup (Firewall, Routing, NAT, QoS, ADSL) Access Management (ACL, Filter, SNMP, UPnP, DDNS) Maintenance (Administration, Time Zone, Firmware, SysRestart, Diagnositics) Status (Device Info, System Log, Statistics) Help Please see the relevant sections of this manual f
4.1 Quick Start For detailed instructions on configuring WAN settings, see the Interface Setup section of this manual. The Quick Start Wizard is a useful and easy utility to help setup the device to quickly connect to your ISP (Internet Service Provider) with only a few steps required. It will guide you step by step to configure the password, time zone, and WAN settings of your device. The Quick Start Wizard is a helpful guide for first time users to the device.
Step1. Set your new password. Step2: Choose your time zone.
Step3: Set your Internet connection.
Step4: Wireless Network configuration.
Step5: Save settings of this ADSL Router.
4.2 Interface Setup Click this item to access the following sub-items that configure the ADSL2+ router: Internet, LAN and Wireless. These functions are described in the following sections. 4.2.
ATM VC ATM settings are used to connect to your ISP. Your ISP provides VPI, VCI settings to you.
from your ISP. You need to activate the VC to take effect. For PVCs management, you can use ATM QoS to setup each PVC traffic line's priority. Virtual Circuit: VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit. PVC Summary: VPI: The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. This field may already be configured. VCI: The valid range for the VCI is 1 to 65535. Enter the VCI assigned to you. This field may already be configured.
Router will not accept the IP address if it is not in this format. PPPoA/PPPoE: Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection. Please enter the information accordingly. PPPoE/PPPoA Select this option if your ISP requires you to use a PPPoE connection.
RIP Version: (Routing Information protocol) Select this option to specify the RIP version, including RIP-1, RIP-2M and RIP-2B. RIP-2M and RIP-2B are both sent in RIP-2 format; the difference is that RIP-2M using Multicast and RIP-2B using Broadcast format RIP Direction: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information then incorporate into routing table.
4.2.2 LAN A Local Area Network (LAN) is a shared communication system to which many computers are attached and is limited to the immediate area, usually the same building or floor of a building. Router Local IP IP Address: Enter the IP address of ADSL Router in dotted decimal notation, for example, 192.168.1.254 (factory default). IP Subnet Mask: The default is 255.255.255.0. User can change it to other such as 255.255.255.128. Dynamic Route: Select the RIP version from RIP-1, RIP-2B and RIP-2M.
obtain TCP/IP configuration at start-up from a server. DHCP: If set to Enabled, your BiPAC 5200N can assign IP addresses, an IP default gateway and DNS servers to Windows 95, Windows NT and other systems that support the DHCP client. If set to Disabled, the DHCP server will be disabled. If set to Relay, the BiPAC 5200N acts as a surrogate DHCP server and relays DHCP requests and responses between the remote server and the clients.
4.2.3 Wireless This section introduces the wireless LAN and some basic configurations. Wireless LANs can be as simple as two computers with wireless LAN cards communicating in a peer-to-peer network or as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to the wired LAN. Access Point Settings Access Point: Default setting is set to Activated. If you do not have any wireless, both 802.11g, 802.11b and 802.
value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network. RTS/CTS Threshold: The RTS (Request To Send) threshold (number of bytes) for enabling RTS/CTS handshake. Data with its frame size larger than this value will perform the RTS/CTS handshake. Setting this attribute to be larger than the maximum MSDU (MAC service data unit) size turns off the RTS/CTS handshake. Setting this attribute to zero turns on the RTS/CTS handshake.
Use WPS: select “yes” or “No” to enable or disable the WPS function SSID: The SSID is the unique name of a wireless access point (AP) to be distinguished from another. For security propose, change the default wlan-ap to a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 30 characters. Make sure your wireless clients have exactly the SSID as the device, in order to get connected to your network.
WPS Settings WPS (WiFi Protected Setup) feature is a standard protocol created by Wi-Fi Alliance. This feature greatly simplifies the steps needed to create a Wi-Fi networks for a residential or an office setting. WPS supports 2 types of configuration methods which are commonly known among consumers: PIN Method & PBC Method. To see the configurations of WPS，please refer to Wi-Fi Network Setup for more information. WPS State: Displays whether the WPS is configured or unconfigured.
Wi-Fi Network Setup To enable WPS function as follows: 43
PIN Method: Configure AP as Registrar 1. Jot down the client’s Pin (eg. 04640776). 2. Enter the Enrollee PIN code and then press Start WPS.
3. Launch the wireless client’s WPS utility (eg. Ralink Utility). Set the Config Mode as Enrollee, press the WPS button on the top bar, select the AP (eg. 5200N) from the WPS AP List column. Then press the PIN button located on the middle left of the page to run the scan.
4. The client’s SSID and security setting will now be configured to match the SSID and security setting of the registrar.
PIN Method: Configure AP as Enrollee 1. Jot down the WPS PIN (eg. 87343540).Press Start WPS.
2. Launch the wireless client’s WPS utility (eg. Ralink Utility). Set the Config Mode as Registrar. Enter the PIN number in the PIN Code column then choose the correct AP (eg. 5200N) from the WPS AP List section before pressing the PIN button to run the scan.
3. The router’s (AP’s) SSID and security setting will now be configured to match the SSID and security setting of the registrar. 4. Now to make sure that the setup is correctly done, cross check to see if the SSID and the security setting of the registrar setting match with the parameters found on both Wireless Configuration and Wireless Security Configuration page.
PBC Method: 1. Press the PBC radio button ,Then Start WPS. 2. Launch the wireless client’s WPS Utility (eg. Ralink Utility). Set the Config Mode as Enrollee. Then press the WPS button and choose the correct AP (eg. 5200N) from the WPS AP List section before pressing the PBC button to run the scan.
3. When the PBC button is pushed, a wireless communication will be established between your router and the PC. The client’s SSID and security setting will now be configured to match the SSID and security setting of the router.
WEP Key 1 to Key 4: Enter the key to encrypt wireless data. To allow encrypted data transmission, the WEP Encryption Key values on all wireless stations must be the same as the router. There are four keys for your selection. The input format is in HEX style, 5 and 13 HEX codes are required for 64-bitWEP and 128-bitWEP respectively. If you chose WEP 64-bits, then enter any 5 ASCII characters or 10 hexadecimal characters ("0-9", "A-F").
Pre-Shared key: The key for network authentication. The input format should be 8-63 ASKII characters or 64 hexadecimal characters Wireless MAC Address Filter The MAC filter screen allows you to configure the router to give exclusive access to up to 8 devices (Allow Association) or exclude up to 8 devices from accessing the router (Deny Association). Every Ethernet device has a unique MAC (Media Access Control) address.
4.3 Advanced Setup 4.3.1 Firewall Your router includes a firewall for controlling Internet access from your LAN and helping to prevent attacks from hackers. In addition to this, when using NAT (Network Address Translation) the router acts as a “natural” Internet firewall, since all PCs on your LAN use private IP addresses that cannot be directly accessed from the Internet.
4.3.2 Routing If you have another router with a LAN-to-LAN connection, you may create a static routing on the router that is the gateway to Internet. #: Item number Dest IP: IP address of the destination network Mask: The destination mask address. Gateway IP: IP address of the gateway or existing interface that this route uses. Metric: It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15.
ADD Route Destination IP Address：This is the destination subnet IP address. IP Subnet Mask：A subnet mask allows IP networks to be subdivided for security and performance purposes. Gateway IP Address：This is the gateway IP address to which packets are to be forwarded. Metric：It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15.
4.3.3 NAT The NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet. The default setting is Dynamic NAT. It provides dynamic Network Address Translation capability between LAN and multiple WAN connections, and the LAN traffic is routed to appropriate WAN connections based on the destination IP addresses and Route Table. This eliminates the need for the static NAT session configuration between multiple LAN clients and multiple WAN connections.
DMZ The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packets will be checked by the Firewall and NAT algorithms then passed to the DMZ host, when a packet received does not use a port number used by any other Virtual Server entries. DMZ setting for: indicate the related LAN PC and PVC ports which allow outside network to connect in and communicate. DMZ: ~ Disabled: As set in default setting, it disables the DMZ function.
incoming connection attempts using specific ports to the PC on your network running the application. You will also need to use port forwarding if you want to host an online game server. The reason for this is that when using NAT, your publicly accessible IP address will be used by and point to your router, which then needs to deliver all traffic to the private IP addresses used by your PCs. Please see the WAN configuration section of this manual for more information on NAT.
Rule Index: Choose the rule number. Application: Choose the predefined rule from Application drop-down menu or enter a custom name. Protocol: Choose the Protocol Type, ALL, TCP or UDP. Start Port Number: Enter a port number as the beginning number of the range which you want to give to devices to access in this field. End Port Number: Enter a port number as the ending number of the range which you want to give to devices to access in this field. Local IP Address: Enter your server IP address in this field.
IP Address Mapping Address Mapping Rule: Shows the PVC where the rule will be applied to Rule Index: Choose the rule number. Rule Type: ~ One-to-one: This is the mode maps one local IP address to one global IP address. Note that port numbers do not change for the One-to-one NAT mapping type. ~ Many-to-One: This is the mode maps multiple local IP addresses to one global IP address. This is equivalent to Many to One (i.e., PAT, port address translation).
local IP addresses, then enter 0.0.0.0 as the Local Start IP address and 255.255.255.255 as the Local End IP address. This field is N/A for One-to-one and Server mapping types. Public Start IP: This is the start range for Inside Public IP Address. Enter 0.0.0.0 here if you have a dynamic IP address from your ISP. Public End IP: This is the end range for Inside Public IP Address. This field is N/A for One-to-one, Many-to-One and Server mapping types.
QoS can be toggled Activated and Deactivated. QoS must be activated before you can edit the following options. When you are done making changes, click on Add to save your changes.
Click on QoS Settings Summary to view the list of QoS rules that have been added.
Rule You can set 16 different QoS rules. Each QoS rule has its detail setting conditions like: 802.1p,application, DSCP, IP, MAC, Protocol, TOS, VLAN…etc, you can modify the default value to any new one you wish. Please notice that only when the packet fulfill every detail setting conditions here, then this packet will be remarked as the priority queue of each rule. The non-selected setting part will be treated as “don’t care” and the system will not handle this setting part.
side. Source MAC: Set the Ethernet MAC value that you want to filter in source side. Source IP: Set the IP address value that you want to filter in source side. Source Mask: Set the subnet mask value that you want to filter in source side. Source Port Range: Set the port range value that you want to filter in source side. Protocol ID: Set the protocol ID type that you want to filter. Vlan ID Range: Set the Vlan value that you want to filter. IPP/DS Field: Select IP QoS format.
4.3.5 ADSL ADSL Mode: The default setting is Auto Sync-Up. This mode will automatically detect your ADSL, ADSL2+, ADSL2, G.DMT, G.lite, and T1.413. But in some area, multimode cannot detect the ADSL line code well. If it is the case, please adjust the ADSL line code to G.DMT or T1.413 first. If it still fails, please try the other values such as ALCTL, ADI, etc.
4.4 Access Management 4.4.1 ACL Access Control Listing allows you to determine which services/protocols can access BiPAC 5200N interface from which computers. ACL Rule Index: This is item number Secure IP Address: The default 0.0.0.0 allows any client to use this service to remotely manage the BiPAC 5200N. Type an IP address to restrict access to a client with a matching IP address. Application: Choose a service that you may use to remotely manage the BiPAC 5200N. Interface: Select the access interface.
4.4.2 Filter You can Filter the packages by IP port , MAC and Application. Filter Type Filter Type Selection: There are three types ”IP/MAC Filter”, ”Application Filter”, and “URL Filter” that user can select for this connection. IP/MAC Filter Set Editing IP/MAC Filter Set Index: This is item number Interface: Select which channel (PVC) to configure.
(“Incoming”).or Both. IP/MAC Filter Rule Editing IP/MAC Filter Rule Index: This is item number Rule Type: Choose “IP” or “MAC” rules Active: Select Yes from the drop down list box to enable IP filter rule. Source IP Address: The source IP address or range of packets to be monitored. Subnet Mask: It is the source IP addresses based on above source subnet IP Source Port Number: This Port or Port Ranges defines the port allowed to be used by the Remote/WAN to connect to the application.
Application Filter Application Filter: Select this option to Activated/Deactivated the Application filter. ICQ: Select this option to Allow/Deny ICQ. MSN: Select this option to Allow/Deny MSN. YMSG: Select this option to Allow/Deny Yahoo messenger. Real Audio/Video: Select this option to Allow/Deny Real Audio/Video.
URL Filter Active: Select Yes to enable URL Filter. URL Index: This is item number. URL: Allow you to prevent users on your network from accessing particular websites by their URL.
4.4.3 SNMP Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. BiPAC 5200N supports SNMP agent functionality which allows a manager station to manage and monitor the router through the network. Get Community: Type the Get Community, which is the password for the incoming Get-and GetNext requests from the management station.
4.4.4 UPnP UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP offers many advantages for users running NAT routers through UPnP NAT Traversal, and on supported systems makes tasks such as port forwarding much easier by letting the application control the required settings, removing the need for the user to control advanced configuration of their device.
4.4.5 DDNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is especially useful for hosting servers via your ADSL connection, so that anyone wishing to connect to you may use your domain name, rather than having to use your dynamic IP address, which changes from time to time. This dynamic IP address is the WAN IP address of the router, which is assigned to you by your ISP.
4.5 Maintenance 4.5.1 Administrator In factory setting, the default password is admin, and that for user is also password. You can change the default password to ensure that someone cannot adjust your settings without your permission. Every time you change your password, please record the password and keep it at a safe place. New Password: Type the new password in this field Confirm Password: Type the new password again in this field.
4.5.2 Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network. Choose your local time zone. After a successful connection to the Internet, the router will retrieve the correct local time from the SNTP server you have specified. If you prefer to specify an SNTP server other than those in the drop-down list, simply enter its IP address as shown above.
4.5.3 Firmware Your router’s “firmware” is the software that allows it to operate and provides all its functionality. Think of your router as a dedicated computer, and the firmware as the software it runs. Over time this software may be improved and modified, and your router allows you to upgrade the software it runs to take advantage of these changes. To upgrade the firmware of BiPAC 5200N, you should download or copy the firmware to your local environment first.
screen. If the upload was not successful, the following screen will appear. Click Back to go back to the Firmware screen. DO NOT power down the router or interrupt the firmware upgrading while it is still in process. Improper operation could damage the router. Warning 4.5.4 SysRestart Click SysRestart with option Current Settings to reboot your router (and restore your last saved configuration).
4.5.
4.6 Status 4.6.1 Device Info This page displays the current information for the ADSL Router. It will display the Firmware version, LAN, WAN, and MAC address information.
LAN IP Address: LAN port IP address. Sub Net Mask: LAN port IP subnet mask. DHCP Server: LAN port DHCP role - Enabled, Relay or disabled WAN Status: “Not connected” or “Connected” Virtual Circuit: There are eight groups of PVC can be defined. VPI: The valid range for the VPI is 0 to 255 VCI: The valid range for the VCI is 1 to 65535 Connection Type: Name of the WAN connection. IP Address: WAN port IP address. Subnet Mask: WAN port IP subnet mask. Default Gateway: The IP address of the default gateway.
4.6.2 System Log Display system logs accumulated up to the present time. You can trace historical information with this function.
4.6.3 Statistics Read-only information here includes port status and packet specific statistics. Also provided are "Transmit Statistics" and "Receive Statistics". Ethernet Interface: This field displays the type of port Transmit Frames: This field displays the number of frames transmitted in the last second. Transmit Multicast Frames: This field displays the number of multicast frames transmitted in the last second.
ADSL Transmit total PDUs: This field displays the number of total PDU transmitted in the last second. Transmit total Error Counts: This field displays the number of total error transmitted in the last second. Receive total PDUs: This field displays the number of total PDU received in the last second. Receive total Error Counts: This field displays the number of total error received in the last second. WLAN Tx Frames Count: This field displays the number of frames transmitted in the last second.
Tx Errors Count: This field displays the number of errors frames transmitted in the last second. Tx Drops Count: This field displays the number of drops frames transmitted in the last second. Rx Frames Count: This field displays the number of frames received in the last second. Rx Errors Count: This field displays the number of errors frames received in the last second. Rx Drops Count: This field displays the number of drops frames received in the last second.
4.7 Help This help page provides you some useful messages such as the introductions of some concepts and some guidances. When some problems are encountered, you can turn to this page for help.
For example, if you don’t understand what is Quick Start, you can go to this page, click on Quick Start, then you’ll see some messages about it, and understand it quickly. This function provides you an easy way to help yourself.
Chapter 5 Troubleshooting If the ADSL2+ Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems starting up the router Problem Corrective Action None of the LEDs Check the connection between the adapter and the router. If are on when you the error persists, you may have a hardware problem.
Problems with the WAN Interface Problem Corrective Action Initialization of the Ensure that the telephone cable is connected properly from PVC connection the ADSL port to the wall jack. The ADSL LED on the front (“linesync”) failed. panel of the router should be on. Check that your VPI, VCI, encapsulation type and type of multiplexing settings are the same as those provided by your ISP. Reboot the router GE. If you still have problems, you may need to verify these settings with your ISP.
APPENDIX Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User’s Manual. If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer where you purchased this product. Contact Billion WORLDWIDE http://www.billion.com MAC OS is a registered Trademark of Apple Computer, Inc.
