Telkom ADSL 5102G Router Quick Start Guide
Telkom ADSL 5102G This Quick start guide describes a basic installation. For instructions on configuring a more detailed setup, please refer to the on-line manual. Package Content: Ethernet (Cat -5 LAN) cable - Straight 2 X RJ-11 ADSL/telephone Cable Integrated Power and surge unit CD-ROM This Quick Start Guide Telkom ADSL 5102G router 2 X ADSL Micro-filters Warning Attention ü Do not use the Telkom ADSL 5102G in high humidity or high temperature rooms and/or surroundings. I.e. Kitchens.
Quick Start Guide The Front LEDs 6 5 4 3 2 1 Figure 1 LED 2 Meaning 1 PWR : Lit when power is ON. 2 SYS : Lit when the router is ready. 3 WLAN: Lit green when wireless connection is established. Flashes when sending/receiving data 4 LAN Port 1-4: 5 ADSL: 6 PPP : Lit when connected to an Ethernet device. Green for 100Mbps; Orange for 10Mbps. Flashes when sending/receiving data Lit steadily when successfully connected to an ADSL DSLAM (“linesync”).
Telkom ADSL 5102G The Rear Ports 5 4 3 2 1 2 Figure 2 Port Meaning 1 Power Switch Power ON/OFF switch 2 PWR Connect the supplied power adapter to this socket. RESET The moment the device is powered on, press it to reset the device or restore to factory default settings. 0-3 seconds: reset the device 6 seconds above : restore to factory default settings (this is used when you can not login to the router, e.g.
Quick Start Guide Start installing your Telkom ADSL 5102G Advanced users: ü ü ü Attention Advanced users may access the router on the following IP address: 10.0.0.2 The default username and password is “admin” and “admin”. Important Note: It is a security risk to leave your username and password as the default. Please change them. Please refer to the online user manual for assistance. ü The following sections of this guide are only applicable to users running Microsoft Windows operating systems.
Telkom ADSL 5102G Installation u sing Windows XP or Windows 2000: An easy installation wizard has been developed to simplify the installation process for users running the newer versions of Windows. The process has been well documented and online help/supplementary info has been provided for each step. ü The wizard has been included on the enclosed CD and will be installed on your hard drive once you insert the CD. ü The wizard installation process is very easy and is described in detail below.
Quick Start Guide 3. The initial installer will open automatically (See figure below). This utility will install the wizard and other useful 5102G utilities onto your hard drive. Just follow the onscreen instructions and complete all the steps. Initial Installer (Figure 6) 4. When you have successfully completed the previous step, the wizard will be installed on your hard drive. To run the wizard click on Start> All programs> Telkom ADSL 5102G> Telkom ADSL 5102G Install Wizard.
Telkom ADSL 5102G 5. The easy install wizard will open on your screen. (See figures below) Please note the supplementary information block to the right edge of the form. This block will provide you with relevant information pertaining to the current step and/or specific buttons or actions. To receive supplementary information on a specific button or object move your mouse cursor over the item in question. The information will appear in the information block until you move the cursor away from the item.
Quick Start Guide Installation using Windows 98, 98SE, ME or NT4: Connecting Your Telkom ADSL 5102G Router (Hardware Installation) Follow the installation instructions below, using the images provided and the overview sketch (figure 3) and the corresponding letter indicators. 1. Power up the device a) Plug the power adapter into the electrical wall-socket (A). b) Plug the power pin-connector (male) into the router’s power socket (B). c) Switch on the device.
Telkom ADSL 5102G c) Your router will now attempt to synchronize with the Telkom ADSL line. The “ADSL” LED will come on, start to blink and after approximately 1-2 minutes be steadily lit. If the “ADSL” LED does not come on, please refer to the troubleshooting section at the end of this guide. d) The Telkom ADSL 5102G router is, by default, distributed with a guest ISP username and password. This guest account allows you access to the www.telkom.co.za website only.
Quick Start Guide G H d) Important Note: Make sure that you do not connect any micro filters between the Telkom wall socket used for the router and the router itself. Refer to the overview sketch, from indicator (C) to indicator (D). Figure 3: Hardware Installation Overview Once the hardware is correctly installed and the “ADSL” & “PPP” LED is steadily lit then you can proceed with the next section of the quick start guide.
Telkom ADSL 5102G Configuring PC in Windows 98/ME 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP -> NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3. Select the Obtain an IP address automatically radio button. 4. Then select the DNS Configuration tab. 5. Select the Disable DNS radio button and click OK. 6. Click OK again to finish the configuration.
Quick Start Guide Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button. 4. Now select the DNS tab and make sure that no DNS is specified. 5. Click OK to close TCP/IP Properties. 6. Click OK again to close the Network window.
Telkom ADSL 5102G Configuring Your Telkom ADSL 5102G Router (Software Installation using Windows 98, 98SE, ME or NT4 ) Now that the hardware installation is complete you will need to perform certain soft actions to complete the installation. All these actions are made easy by using the enclosed Telkom ADSL 5102G CD. In this section you will: 1) Verify that your computer meets the minimum requirements for Telkom ADSL 2) Test your guest account connection to the www.telkom.co.
Quick Start Guide ü If nothing happens when you insert the CD, please refer to the troubleshooting section at the end of this guide. ü Not all buttons are active when the utility starts up. As you perform the actions from top to bottom they will become available. 3) Click “PC Qualification Test”. A program will open to verify that your PC meets the minimum requirements. Just follow the instructions and when complete, close the program to return to the menu screen.
Telkom ADSL 5102G Telkom ADSL 5102G utility (Figure 5) After you have entered your details, click on “Save ”. The router will now be updated with your own ISP account. On successful completion, a message will be displayed reporting that the save process was a success. Just click “Ok” and close the utility to proceed to the next step. ü If the utility does not seem to respond, please refer to the troubleshooting section.
Quick Start Guide 5102G. The manual is in Adobe Acrobat PDF format and requires Acrobat reader to open the file. If you do not have Acrobat reader installed on your PC. Click on the “Install Acrobat Reader….” hyperlink to the immediate right of the manual button, select your operating system and click install. ü ü You have now completed the Telkom ADSL 5102G setup (for Windows 98, 98SE, ME or NT4) and should now be able to browse the Internet.
Telkom ADSL 5102G Troubleshooting: Problem Description 1: ADSL LED (light) does not come on. Solution: 1. Check line connection at wall socket (C) and on router (D). (Refer to overview sketch – figure 3) 2. Make sure the micro filters are connected as illustrated in the overview sketch (figure 3) and not directly between the Telkom ADSL wall socket (C) and the Telkom ADSL 5102G router (D). 3.
Quick Start Guide Problem Description 4: When the wizard tries to open the Telkom website or when I try to open any other website, a Dial-up Connection screen pops up asking me to connect to the internet. It doesn’t matter what choice I make I can not connect or see the website. Solution: 1. Your Internet explorer is still setup to connect to the Internet using a dial-up account such as traditional analog or ISDN. Please change this setting to “Never Dial a connection”.
