user manual

SkyRider 15
5-2
B06-00-0386
B06-00-0383
B06-00-0289
B06-00-0382
B06-00-0296
B06-00-0009
B06-00-0173
B06-00-0286
B06-00-0146
B06-00-0138
B06-00-0359
B06-00-0349
B06-00-0137
B06-00-0385
B06-00-0170
B06-00-0034
B06-00-0384
TURN RED KNOB COUNTER
CLOCKWISE TO LOWER
CCFA
B06-00-0286
B06-00-0225
STAY CLEAR
WHILE RAISING
OR LOWERING
B06-00-0225
CCFO
Stand clear when raising or
lowering lift.
Pot hole protection device
automatically lowers while lift is
being raised.
Contact with pot hole protection
device will cause serious crushing
injury.
UOT B06-00-0384
This machine is designed and manufactured in
compliance with the ANSI A92.6 standard in force on
the date of manufacture. Dealers, owners, users,
operators, lessors, and lessees are responsible for
inspection, maintenance, training, and operation as
required by A92.6 and the owners manual.
Alterations, modifications, or changes to this
machine without the written authorization of bil-jax,
inc. as well as any unauthorized adjustment of valves,
disabling or by-passing of safety devices or the
improper use of this machine shall exempt bil-jax, inc.
from any liability for any resulting injuries or damage.
B06-00-0382UOT
IF YOU HAVE NOT BEEN PROVIDED WITH SAFETY
LITERATURE, OR FOR ANY QUESTIONS CONCERNING
THE SAFE USE OF THIS EQUIPMENT, CALL 419/445-9675.
Inspect unit for damaged or worn
if lift is not working properly.
DO NOT use when exposed to
wind, rain, snow or ice.
DO NOTuse wherelift cancome
into contact with overhead ob-
structions such as electrical
wires, cables,ropes orover-
DO NOTdrive nearloading docks,
ditches, holes, unguarded open-
ings, openelevated shaftsor
parts. DO NOT use until such
parts are replaced. DO NOT use
B06-00-0383UOT
FAILURE TO COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS OR ANY OTHER IMPROPER
USE OF THIS EQUIPMENT WILL RESULT IN SERIOUS INJURY OR DEATH.
It is the operator's responsibility to comply with all warnings and instructions.
drugs or alcohol, or if you fell dizzy, ill or unsteady in any way.
ALWAYS survey the job site and identify all potential hazards.
affect the original design of the lift.
Check all safety devices for
proper function prior to each use.
DO NOT use without entry gate in
the closed position unless operator is wearing a full body harness and lanyard and with
the lanyard attached to factory provided attachment point.
DO NOT raise platform while on uneven, soft, or sloped surfaces.
DO NOT DRIVE lift onto uneven,
soft, or sloped surfaces while
elevated.
•
•
•
•
•
•
Work only within the platform guard rail area and do not attempt to increase working
height with boxes, ladders, scaffolding or any other means.
drop-offs.
or overhangs, etc..
DO NOT exert horizontal force to platform while performing work.
DO NOT move lift if you do not have a clear view of the path of travel.
DO NOT exceed manufacturer's recommended load capacity.
•
•
•
•
•
•
DONOTstandorsitonguardrails..
DO NOT lean out over guard rails to perform work.
DO NOT raise or lower lift until you are certain all personnel are clear.
DO NOT use near cranes or other moving vehicles.
DO NOT leave keys in machine while unattended.
DO NOT allow flames, sparks or embers near batteries and do not smoke near
batteries. Batteries produce highly flammable gases which can explode.
OWNERS & OPERATORS ARE RESPONSIBLE FOR INSPECTION, MAINTENANCE,
TRAINING, AND OPERATION AS REQUIRED BY THE OWNERS MANUAL AND THE
ANSI A92.6 STANDARD (IN EFFECT AT DATE OF MANUFACTURE).
UOT
B06-00-0386
OPERATION INSTRUCTIONS FOR SKYRIDER 15
1. Read and follow safety precautions and all responsibilities sections set forth in the operators manual
2. Make sure the lift is on a firm and level surface and that there are no potential hazards such as overhead
obstructions or electrically charged conductors, use the lift where such hazards exist.
3. Check the lift for damaged or worn parts and repair or replace as necessary.
4. Check to be sure that the cage is properly attached to the lift.
5. Turn master switch to on. Switch is located on the side of the lift.
6. Check to be sure all safety devices are functioning properly.
7. To operate lift from the ground turn and hold lower control switch to "lower control" setting then select either
up or down function.
8. To operate lift from the platform, turn lower control switch to "upper control" setting.
9. Enter platform and be certain that the entry gate is closed completely. If operating with entry gate open, operator
must wear full body harness and lanyard. Stand with back to the mast sections and face entry gate.
TORAISEORLOWER:
Depress and hold the "enable" button (this must be done prior to any other function being activated or reset of
the controls will be necessary).
Press either the raise or lower button.
TO DRIVE:
Depress and hold the "enable" button (this must be done prior to any other function being activated or reset of
the controls will be necessary).
Push joystick in the direction (forward or backward) that you wish to travel.
Press the steering thumb switch on the top of the joystick in the direction you wish the lift to turn (either right
or left).
The joystick and steering thumb switch may be operated simultaneously for smooth maneuvering.
DO NOT attempt to operate the drive function and the raise/lower function at the same time. The unit will
stop operating and reset of the controls will be necessary.
This lift is equipped with a level sensor that will prevent the lift from raising or driving with platform elevated
while on an unlevel surface. If the lift fails to raise or drive while elevated, lower platform immediately.
DO NOT
•
•
•
•
•
•
•
24V DC
PATENT PENDING
12FT.
SP-
B06-00-0130
LUBRICATE
MONTHLY
B06-00-0130
RIF
B06-00-0390
COFC B06-00-0192
B06-00-0192
OPERATION AND SERVICE
MANUAL INSIDE
B06-00-0387
SR 15KY IDER
B06-00-0388
SR 15KY IDER
AERIAL WORK PLATFORMS
This equipment to be used by competent, fully trained, and authorized personnel only.
Operator must read and understand owner's manual and all decals before operating.
DO NOT override or alter any safety devices or make any modifications that would
NEVER TAKE CHANCES - DO NOT operate this lift if you are under the influence of
•
•
•
•
•
•
•
•
•
•
•
DURING USE:
BEFORE USE:
DO NOT climb up or down masts.
Full Body Harness and Lanyard
must be used whenever lift is
operated with entry gate open.
Failure to wear Full Body Harness
and Lanyard may allow operator
to fall from platform resulting in
serious injury or death.
Transaxle
Free Wheel
Normal Drive
Figure 5-1. Replacement Decals