Instruction manual

CR4105-S SKYBOX
®
DELUXE
WARNING! Read USAGE INSTRUCTIONS & WARNINGS and FULL BODY
FALL-ARREST HARNESS USAGE INSTRUCTIONS & WARNINGS on pages 3-11
prior to assembly of this product! Failure to follow the instructions on this page
and pages 3-11 may result in serious injury or death!
NOTE: Steps 1-7 require you to temporarily finger tighten nuts to insure proper
alignment. All bolts should be installed from the inside with nylock nuts on the outside.
STEP 1: Attach top ladder extensions & lower under support gussets to the top ladder
section using (2) ¼" x 2 ½" hex bolts [E] and (2) ¼" nylock nuts. Note: When attaching
top ladder extensions be sure that the bends are facing outward. The non-tabbed end
of the lower under support gussets should be attached to the outside of the top ladder
section while the tab on the tabbed end is to the outside. Next, attach the side frames
to the top ladder extensions using (2) ¼" x 1 ¾" hex bolts [C] and (2) ¼" nylock nuts.
STEP 2: Attach rear frame support & upper under
support gussets to side frames using (2)¼" x 2 ¼" hex
bolts [D] and (2) ¼" nylock nuts to secure the rear holes.
Note: The backrest support on the rear frame support
should face upward and lean slightly backward and the
upper under support gussets should be attached to
the outside of the side frames.
STEP 3: Next attach the left/right shooting rails to the
side frame and rear frame support using the front holes
of the rear frame support and (2) ¼" x 1 ¾" hex bolts [C],
(2) nylon washers and (2) ¼" nylock nuts to secure.
STEP 4. Finish the assembly of the shooting rail by
attaching the shooting rail main piece to the upper
ends of the left/right shooting rails using (2) ¼" x 1
¼" hex bolts [A] and (2) ¼" nylock nuts to secure.
STEP 5: Attach the seat bracket and theplatform supports
to the front holes in theside frames using(2) ¼"x 1 ¾" hex
bolts [C] and (2) ¼" nylock nuts. Note: Platform supports
should be assembled with the multiple bend on the outside
of the side frame with the lower end bent inward.
STEP 6: Next, attach the seat platform to the seat bracket
using (2) ¼" x 1 ½" hex bolts [B] and (2) ¼" nylock nuts.
Then attach seat platform support to the bottom of the
rear frame support and finally to the seat platform using
(2) ¼" x 1 ½" hex bolts [B] and (2) ¼" nylock nuts.
STEP 7: Next, attach the foot platform to the top ladder
extensions using (2) ¼" x 2 ¼" hex bolts [D] and (2) ¼"
nylock nuts to secure. Then attach the platform
supports, lower & upper under support gussets to the
foot platform using (2) ¼" x 2 ¼" hex bolts [D] and (2)
¼" nylock nuts. Note: The platform support should be
next to the foot platform, then the lower under support
gusset tab and lastly the upper under support gusset.
STEP 8: SECURELY TIGHTEN EVERY NUT AND
BOLT AT THIS TIME.
STEP 9: Fasten seat cushion and backrest cushion.
Attach padded shooting rail cover with velcro.
Please refer to pages 60-65 for ladderstand installation instructions.
Parts List (CR4105-S)
26
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
Description Qty
Top Ladder Section 1
Middle Ladder Section 2
Bottom Ladder Section 1
Foot Platform 1
Seat Platform 1
Side Frame 2
Rear Frame Support 1
Seat Platform Support 1
Seat Bracket 1
Platform Support 2
Upper Under Support Gusset 2
Lower Under Support Gusset 2
Seat Cushion 1
Backrest Cushion 1
Right Shooting Rail Side Piece 1
Left Shooting Rail Side Piece 1
Shooting Rail Main Piece 1
Shooting Rail Cover 1
Support Bar- Tree Piece 1
Support Bar- Ladder Piece 1
Top Ladder Extension 2
Rope 1
Ratchet Strap 1
Stabilizer Strap 2
Full Body Harness 1
Owners Manual 1
[A] 1/4" x 1 1/4" Hex Bolt 2
[B] 1/4" x 1 1/2" Hex Bolt 4
[C] 1/4" x 1 3/4" Hex Bolt 7
[D] 1/4" x 2 1/4" Hex Bolt 6
[E] 1/4" x 2 1/2 " Hex Bolt 2
Nylon Washer 2
1/4" Wing Nut 1
1/4" Nylock Nut 20
Snap Pin 7