SO M E RSET LODGE PLAY SYSTEM – F23 1 6 5 14'2" 28'6" INSTALLATION AND OPERATING INSTRUCTIONS WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer to these instructions often and give them to any future owner of this play system. Manufacturer contact information provided below. MAXIMUM VERTICAL FALL HEIGHT - 7’1” (2.16 m) 16' 28'0" OBSTACLE FREE SAFETY ZONE - 28’ 6” x 28’ area requires Protective Surfacing. See page 3.
Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.
support@solowavedesign.
support@solowavedesign.
support@solowavedesign.
Keys to Assembly Success Tools Required Shovel Measuring Tape Drill (1/8” 3/16” Bit) Safety Glasses Hammer Part Identification Key On each page, you will find the parts and quantities required to complete the assembly step illustrated on that page. Here is a sample. Ratchet 1/2”, 7/16” & 9/16” Level #2 & #3 Phillips or Robertson Square Ruler Step Ladder 2X 123 1234 Post 2 x 4 x 83” Symbols Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
5/16" (8mm) Flat Washer 1/4" (6mm) Lock Washer 5/16" (8mm) T-Nut 1/4" (6mm) T-Nut 1/4" (6mm) Flat Washer 5/16" (8mm) Flat Washer For example: BOLT LENGTH 4½ (4.5) inches long 1 inch = 25.4mm LENGTH CONVERSION 0.31 inches x 25.4mm = 8mm BOLT DIAMETER 5/16 (0.31) inches For example: 1 inch = 25.4mm DIAMETER CONVERSION HARDWARE LENGTH CHART inches vs millimetres 6 152 5½ 140 5 127 114 4½ 4 102 3½ 89 3 76 2½ 64 2 51 1½ 38 1¼ 32 1-1/8 29 1 25.4 7/8 22 3/4 19 1/2 12.
63.5 2 1/2" 5/4 x 3 88.9 3 1/2" 5/4 x 4 114.3 4 1/2" 5/4 x 5 139.7 5 1/2" 5/4 x 6 88.9 3 1/2" 4x4 38.1 1 1/2" 34.9 1 3/8" 34.9 1 3/8" 38.1 1 1/2" 38.1 1 1/2" 2x6 136.5 5 3/8" 2x4 85.7 3 3/8" 2x3 63.5 2 1/2" 2 x2 15.9 5/8" 82.6 3 1/4" 34.9 1 3/8" 60.3 2 3/8" 85.7 3 3/8" 114.3 4 1/2" 136.5 5 3/8" 1/2 x 4 1x2 1x3 1x4 1x5 1x6 LENGTH CONVERSION 1 inch = 25.4mm 59.25 inches x 25.4mm = 1505mm For example: BOARD LENGTH 59¼ (59.25) inches 15.9 5/8" 15.9 5/8" 15.9 5/8" 15.
Part Identification (Reduced Part Size) 4pc. - 041 - 5/8 x 3 x 15" - Window Shutter Green FSC - Box 1 - 4608778 4pc. - 187 - 1 x 4 x 8-1/2" - Side Gable FSC - Box 2 - 4638819 Nominal Size Actual Size 5/8 x 3 1x4 1x5 1x6 19/32 x 3 5/8 x 3-1/4 5/8 x 4-1/4 5/8 x 5-1/4 2pc. - 186 - 1 x 4 x 13-1/2" - Centre Gable FSC - Box 2 - 4638820 1pc. - 023 - 1 x 4 x 15" - Ladder Gap FSC - Box 2 - 4638828 1pc. - 030 - 1 x 4 x 20-1/2" - Board Access FSC - Box 2 - 4638826 4pc.
Part Identification (Reduced Part Size) 2pc. - 411 - 1 x 6 x 27-1/2" - Wall Board FSC - Box 3 - 4638881 Nominal Size Actual Size 1x6 5/4 x 3 2x3 5/8 x 5-1/4 15/16 x 2-1/4 1-1/4 x 2-1/4 5/4 x 4 15/16 x 3-1/4 1pc. - 410 - 1 x 6 x 32" - Center Board FSC - Box 3 - 4638883 6pc. - 152 - 1 x 6 x 36" - Floor FSC - Box 2 - 4638797 3pc. - 150 - 1 x 6 x 42½" - Slidenest Floor FSC - Box 2 - 4638794 1pc. - 112 - 5/4 x 3 x 31-3/4" - SW Table Top FSC - Box 3 - 4638811 1pc.
Part Identification (Reduced Part Size) 1pc. - 181 - 5/4 x 4 x 29" - Roof Support Left FSC - Box 4 - 4638807 Nominal Size Actual Size 5/4 x 4 5/ x 5 15/16 x 3-1/4 15/16 x 4-1/4 1pc. - 401 - 5/4 x 4 x 30-5/8" - Bottom Board FSC - Box 3 - 4638882 1pc. - 190 - 5/4 x 4 x 31" - Right Gable Angle FSC - Box 4 - 4638817 1pc. - 191 - 5/4 x 4 x 31" - Left Gable Angle FSC - Box 4 - 4638818 2pc. - 122 - 5/4 x 4 x 31-7/8" - Post FSC - Box 3 - 4638791 2pc.
Part Identification (Reduced Part Size) 2pc. - 347 - 5/4 x 5 x 31" - Crowsnest Wall FSC - Box 2 - 4638119 Nominal Size Actual Size 5/4 x 5 5/4 x 6 2x3 2x4 1pc. - 080 - 5/4 x 5 x 35-1/2" - Table Top FSC - Box 3 - 4638801 1 x 4-1/2 1 x 5-1/2 1-3/8 x 2-1/2 1-3/8 x 3-3/8 1pc. - 370 - 5/4 x 5 x 36-1/4" - Middle Arch FSC - Box 3 - 4638800 2pc. - 185 - 5/4 x 6 x 10" - Sunburst FSC - Box 2 - 4638614 4pc. - 330 - 5/4 x 6 x 18" - Crowsnest Side FSC - Box 3 - 4638843 2pc.
Part Identification (Reduced Part Size) 1pc. - 192 - 2 x 4 x 34-1/2" - Gable Bottom FSC - Box 3 - 4638816 1pc. - 020 - 2 x 4 x 62-7/8" - Left Access Rail FSC - Box 3 - 4638145 Nominal Size Actual Size 2x4 1-1/4 x 5 2x6 2-1/2 x 3 4x4 3 x 5-1/4 1-3/8 x 3-3/8 1-1/4 x 5 1-1/2 x 5-1/4 2-1/2 x 3 3x3 3 x 5-1/4 1pc. - 021 - 2 x 4 x 62-7/8" - Right Access Rail FSC - Box 4 - 4638146 1pc. - 024 - 2 x 4 x 62-7/8" - Rock Rail FSC - Box 2 - 4638139 1pc.
Part Identification (Reduced Part Size) 2pc. - 050 - 1-1/4 x 16-3/4 x 99" - Narrow Window Panel FSC - Box 3 - 47638837 1pc. - 043 - 1-1/4 x 36 x 87-1/4" - SW Side Panel FSC - Box 2 - 47638775 1pc. - 040 - 1-1/4 x 35-1/2 x 99" - Wall Cafe Window Panel FSC- Box 2 - 47638838 1pc. - 060 - 1-1/4 x 38-1/2 x 57-3/8" - SL Panel FSC - Box 4 - 47638842 1pc. - 051 - 1-1/4 x 30 x 54-1/8" - SL Window Side Panel FSC - Box 2 - 47638841 2pc. - 210 - 1-1/4 x 31-3/4 x 41" - Large Roof Panel FSC - Box 4 - 47638756 2pc.
Hardware Identification (Actual Size) 3pc. WB2 - Wafer Bolt 5/16 x 1-3/8" - (53613316) 5pc. WL3 - Wafer Lag 1/4 x 1-3/8" - (52613216) 17pc. WL5 - Wafer Lag 1/4 x 2-1/2" - (52632222) 14pc. WB9 - Wafer Bolt 5/16 x 2-1/8" - (53613324) 1pc. H1 - Hex Bolt 1/4 x 1-1/2" - (9277212) 6pc. H2 - Hex Bolt 1/4 x 2" - (53703220) 7pc. WB8 - Wafer Bolt 5/16 x 2-3/8" - (53613326) 1pc. H3 - Hex Bolt 1/4 x 2-1/2" - (9277222) 12pc. WB7 - Wafer Bolt 5/16 x 3" - (53613330) 1pc. H5 - Hex Bolt 1/4 x 4-1/2" - (9277242) 5pc.
Hardware Identification (Actual Size) 25pc. LW2 - 5/16" Lock Washer - (51303300) 19pc. LW1 - 1/4" Lock Washer - (51303200) 14pc. FW0 - 3/16" Flat Washer - (51103100) 7pc. TN1 - 1/4" T - Nut -(54303200) 16pc. FW1 - 1/4" Flat Washer - (51103200) 60pc. TN2 - 5/16" T- Nut - (54303300) 89pc. LN1 - 1/4 Lock Nut - (9283200) 95pc. FW2 - 5/16" Flat Washer - (51103300) 12pc. LN2 - 5/16" Lock Nut - (54303300) 10pc. BN1 - 1/4" Barrel Nut - (54803200) 14pc. FW10 - 3/8" Flat Washer - (51103800) 7pc.
Part Identification (Reduced Part Size) 1x - Telescope w/ Mount (3320161) 2x - Steel Hand Grip (9200211) -Yellow 1x - (3pk) Swing Bracket Set (3201530) -Green 1x - Big Backyard Plaque (3320351) 1x.
First Step: Inventory Parts - Read This Before Starting Assembly STOP A. STOP STOP STOP his is the time for you to inventory all your hardware, wood and accessories, T referencing the parts identification sheets. This will assist you with your assembly. • The wood pieces will have the three digit key number stamped on the ends of the boards. The wood pieces are referenced throughout the instructions with this number. • Please refer to Page 6 for proper hardware assembly.
Step 1: Cafe Bench Assembly Part 1 A: Flush to the top of (011) Bench Leg Cafe place (010) Bench End Support Cafe, angled corners facing down and centred on the legs. Attach with 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, flat washer and t-nut). Make sure the top of (010) Bench End Support Cafe is level then attach with 2 (S20) #8 x 1-3/8” Wood Screws as shown in fig. 1.1.
Step 1: Cafe Bench Assembly Part 2 D: Place 2 (013) Bench Top Cafes on both Bench Leg Assemblies so the ends on each side hang over by 1”. Outside edges of each (013) Bench Top Cafe to be flush to outside edge of each (010) Bench End Support Cafe. Attach each (013) Bench Top Cafe to each (010) Bench End Support Cafe with 4 (S15) #8 x 1-3/4” Wood Screws per board. Note: leave a gap of 1/2” minimum between boards on both ends. (fig. 1.3 and 1.
Step 1: Cafe Bench Assembly Part 3 F: Attach 2 Corner Brackets flush to the top and end of each (012) Bench Base Cafe on the inside using 2 (S13) #6 x 5/8” Pan Screws per bracket. (fig. 1.5, 1.6 and 1.7) G: Attach 2 Corner Brackets flush to the bottom and end of each (012) Bench Base Cafe on the outside using 2 (S13) #6 x 5/8” Pan Screws per bracket. (fig. 1.5, 1.6 and 1.8) Fig. 1.7 Inside Fig. 1.5 Flush Corner Bracket 012 012 S13 012 Fig. 1.6 Fig. 1.
Step 2: Access Ladder / Rockwall Assembly Part 1 A: Place (020) Left Access Rail on left hand side of 4 (022) Ladder Treads and (021) Right Access Rail on right hand side with the grooves facing in. (fig. 2.1) B: Fit each (022) Ladder Tread into grooves on both (020) and (021) Access Rails, make sure the top edge of the treads are flush to the front of the Access rails. (fig. 2.1 and 2.
Step 2: Access Ladder / Rockwall Assembly Part 2 E: Place (023) Ladder Gap on each access rail so there is a 2-3/8” gap between (023) Ladder Gap and the top (022) Ladder Tread. Attach using 4 (S20) #8 x 1-3/8” Wood Screws. (fig. 2.4 and 2.5) F: Place (024) Rock Rail on the ground next to (021) Right Access Rail so it matches the orientation of the two access rails as shown in fig. 2.6. Attach (025) Top Ladder to top of Access Ladder assembly and (024) Rock Rail using 3 (S3) #8 x 2-1/2” Wood Screws.
Step 3: Rockwall Assembly Part 1 A: Place (030) Board Access at top of the Access Ladder/Rockwall Assembly and (031) Rock Bottom at the bottom of the assembly as shown in fig. 3.1. Then place (032) Rock Board A, (033) Rock Board B, (034) Rock Board C and (035) Rock Board D as shown in fig. 3.1. Do not screw boards down yet. Rock holes are to be staggered so they do not form a straight line and are at the top of the boards.
Step 3: Rockwall Assembly Part 2 E: Alternating colours and shapes, attach 1 rock to each rock board using 1 (PB2) 1/4 x 1-1/4” Pan Bolt (with lock washer, flat washer and barrel nut) and 1 (S10) #8 x 1” Pan Screw per rock. (fig. 3.4 and 3.5) The Pan Screw is placed in the hole beneath the Pan Bolt. (fig. 3.4 and 3.5) Note: Make sure all hardware is used to secure each rock properly. Fig. 3.4 Fig. 3.
Step 4: Panel Preparation Part 1 A: On the outside of (040) Wall Cafe Window Panel place 2 (041) Window Shutters on each side of both windows. This distance between the shutters should be 11”. (fig. 4.1 and 4.2) B: Attach each (041) Window Shutter to (040) Wall Cafe Window Panel with 3 (TS) #6 x 30 mm Trim Screws per shutter. (fig. 4.2) Note: 2 outer Shutters need to be flush to outside edge of panel. (fig.4.2) Fig. 4.1 040 Fig. 4.
Step 4: Panel Preparation Part 2 C: Place (044) SW Wall at the top of the front of (043) SW Side Panel and attach with 4 (G21) 5/16 x 3-3/4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 4.3 and 4.4) Fig. 4.3 044 043 Fig. 4.
Step 5: Swing Side Wall Assembly Part 1 A: Place 1 (050) Narrow Window Panel on the ground. Measure 3-1/4” up from the bottom of the panel on the right side and attach a 2 x 2-1/4” Corner Panel Bracket to the panel with 2 (S8) #12 x 3/4” Pan Screws. The flat edge of the bracket must be facing up and it must be installed on the correct side. (fig. 5.1 and 5.
Step 5: Swing Side Wall Assembly Part 2 Note: Make sure panels are square and flush to each other. D: Pre-drill with a 3/16” drill bit, then fasten the (050) Narrow Window Panel to (043) SW Side Panel with 3 (WL5) 1/4 x 2-1/2” Wafer Lags. (fig. 5.3 and 5.4) Fig. 5.3 050 043 Fig. 5.4 050 WL5 043 WL5 Flush Outside View Hardware 3x WL5 1/4 x 2-1/2” Wafer Lag 29 support@solowavedesign.
Step 5: Swing Side Wall Assembly Part 3 E: Place (051) SL Window Side Panel on the ground. Measure 3-1/4” up from the bottom of the panel on the left side and attach a 1-1/2 x 2-1/4” Corner Panel Bracket to the panel with 2 (S8) #12 x 3/4” Pan Screws. The flat edge of the bracket must be facing up and it must be installed on the correct side. (fig. 5.5 and 5.
Step 5: Swing Side Wall Assembly Part 4 Note: Make sure panels are square and flush to each other. H: Pre-drill with a 3/16” drill bit, then fasten the (051) SL Window Side Panel to (043) SW Side Panel with 3 (WL5) 1/4 x 2-1/2” Wafer Lags. (fig. 5.7 and 5.8) Fig. 5.7 050 WL5 Fig. 5.8 051 043 Outside View 043 WL5 Flush Hardware 3x WL5 1/4 x 2-1/2” Wafer Lag 31 support@solowavedesign.
Step 6: Crowsnest Side Wall Assembly Part 1 A: On both sides of (060) SL Panel measure 1-1/4” in from each edge, 4” up from the bottom, and 4” down from the top and attach one Narrow Angle Bracket at each location with 1 (S8) #12 x 3/4” Pan Screw per bracket. Centre 1 more Narrow Angle Bracket on each side and attach with 1 (S8) #12 x 3/4” Pan Screw per bracket. (fig. 6.1 and 6.
Step 6: Crowsnest Side Wall Assembly Part 2 Note: Make sure panels are square and flush to each other. D: Pre-drill with a 3/16” drill bit, then fasten the (050) Narrow Window Panel and (040) Wall Cafe Window Panel to (060) SL Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags per side. (fig. 6.3) 060 Fig. 6.3 WL5 050 Outside View Hardware 8x WL5 1/4 x 2-1/2” Wafer Lag 33 support@solowavedesign.
Step 7: Front Wall Assembly Part 1 A: With at least two helpers lift the Crowsnest Side Wall Assembly and Swing Side Wall Assembly so the (040) Wall Cafe Window Panel and (051) SL Window Side Panel meet and are tight together as shown in fig. 7.1 and 7.2. B: Loosely attach (070) Front Ground to (051) SL Window Side Panel and (040) Wall Cafe Window Panel with 4 (WB9) 5/16 x 2-1/8” Wafer Bolts (with flat washer and t-nut) as shown in fig. 7.1, 7.2 and 7.3.
Step 7: Front Wall Assembly Part 2 E: To each (050) Narrow Window Panel loosely attach (072) Back Ground to inside the assembly with 4 (WB9) 5/16 x 2-1/8” Wafer Bolts (with flat washer and t-nut) and (100) Back Top to outside the assembly with 4 (WB9) 5/16 x 2-1/8” Wafer Bolts (with flat washer and t-nut) as shown in fig. 7.5 and 7.6.
Step 7: Front Wall Assembly Part 3 H: On the inside of the assembly attach (040) Wall Cafe Window Panel to (051) SL Window Side Panel using 2 Flat Panel Brackets in the places shown with 4 (S8) #12 x 3/4” Pan Screws per bracket. (fig. 7.8 and 7.9) Fig. 7.8 040 051 Fig. 7.9 051 040 Flat Panel Bracket S8 x 4 per bracket 072 Back Hardware 8x S8 #12 x 3/4” Pan Screw 36 Other Parts 2 x Flat Panel Bracket support@solowavedesign.
Step 8: Attach Floor Joist A: With one person inside the assembly hold (085) Floor Joist up against (060) SL Panel, flush to the top and lined up with the pilot holes then attach with 2 (S4) #8 x 3” Wood Screws. (fig. 8.1 and 8.2) B: Line (085) Floor Joist up to the pilot holes on the (043) SW Side Panel, making sure the top of the joist is flush to the top of the panel board shown in fig. 8.1 then attach with 2 (S4) #8 x 3” Wood Screws. Flush 060 085 Fig. 8.2 Fig. 8.
Step 9: Attach SL Post A: Tight to the top of (051) SL Window Side Panel and tight against (044) SW Wall attach (082) SL Post to (043) SW Side Panel with 3 (S3) #8 x 2-1/2” Wood Screws as shown in fig. 9.1 and 9.2. 082 Fig. 9.1 044 043 082 Fig. 9.2 Tight Front 044 051 S3 043 051 Wood Parts 1x 082 SL Post FSC 1-1/4 x 1-1/4 x 44-7/8” Tight Hardware 3x S3 #8 x 2-1/2” Wood Screw 38 support@solowavedesign.
Step 10: Slide Top Assembly Part 1 A: Loosely attach (120) SL Top Left to 1 (122) Post and (123) SL Top Right to another (122) Post with 1 (G1) 5/16 x 1-1/2” Hex Bolt (with lock washer, flat washer and t-nut) per post. (fig. 10.1 and 10.2) B: Loosely attach 1 (121) Short Joist to the bottom of both (122) Posts with 1 (G8) 5/16 x 2” Hex Bolt (with lock washer, flat washer and t-nut) per post. (fig. 10.1 and 10.
Step 10: Slide Top Assembly Part 2 C: Place Left Side Post Assembly tight to (043) SW Side Panel and (082) SL Post and Right Side Post Assembly tight to (040) Wall Cafe Window Panel so both (121) Short Joists are flush to the top of (071) Front Floor and centred over the pilot holes then attach with 2 (S4) #8 x 3” Wood Screws per assembly. (fig. 10.3 and 10.
Step 10: Slide Top Assembly Part 3 E: Make sure (120) SL Top Left is flush to the inside edge of the panel support on (043) SW Side Panel and (123) SL Top Right is flush to the inside edge of (040) Wall Cafe Window Panel and both boards are level then attach to (043) SW Side Panel and (040) Cafe Wall Window Panel with 2 (S15) #8 x 1-3/4” Wood Screws per board. (fig. 10.5 and 10.6) F: Tighten bolts on each Post Assembly. Fig. 10.5 040 043 Fig. 10.
Step 10: Slide Top Assembly Part 4 G: Flush to the tops of each (122) Post attach (125) SL Top to (120) SL Top Left and (123) SL Top Right with 4 (S3) #8 x 2-1/2” Wood Screws. (fig. 10.7) H: Flush to the tops of (121) Short Joists and (124) Short Floor Joist attach (126) SL End with 6 (S4) #8 x 3” Wood Screws. (fig. 10.7) 123 Flush Fig. 10.
Step 11: Swing Wall Assembly Part 1 Keep all bolts loose in this step. A: Loosely attach (110) Ground SW to the bottom of (043) SW Side Panel using 4 (G8) 5/16 x 2” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 11.1, 11.2 and 11.3) B: At each end of (110) Ground SW loosely attach 1 (111) Diagonal with 1 (G8) 5/16 x 2” Hex Bolt (with lock washer, flat washer and t-nut) per side. (fig. 11.1 and 11.2) Fig. 11.1 Fig. 11.3 043 050 043 5/16” T-Nut Inside View 111 Fig. 11.
Step 11: Swing Wall Assembly Part 2 C: Pre-drill pilot holes with a 3/16” drill bit then attach (111) Diagonal flush to outside edge of (050) Narrow Window Panel and (051) SL Window Side Panel with 1 (WL5) 1/4 x 2-1/2” Wafer Lag (with flat washer) per diagonal. (fig. 11.4) D: Tighten all 6 (G8) 5/16 x 2” Hex Bolts from Step 11 A and B. E: In the opening of (043) SW Side Panel attach (112) SW Table Top, tight to the corner of the panels, with 3 (S4) #8 x 3” Wood Screws as shown in fig. 11.4. S4 Fig.
Step 12: Install Fort Ground Stakes MOVE FORT TO FINAL LOCATION PRIOR TO STAKING FINAL LOCATION MUST BE LEVEL GROUND A: In the 3 places shown in fig. 12.1 drive the Rebar Ground Stakes 13” into the ground against (070) Front Ground and both (111) Diagonals. Be careful not to hit the washer while hammering stakes into the ground as this could cause the washer to break off.
Step 13: Floor Board Assembly Part 1 A: Stagger 3 (150) Slidenest Floors and 3 (151) Slidenest Floor As on (126) SL End, (071) Front Floor, (085) Floor Joist and (073) Back Floor. The first board should be tight to (043) SW Side Panel. (fig. 13.1 and 13.2) B: These floor boards are between both (121) Posts and evenly spaced. Attach all 6 boards with 8 (S20) #8 x 1-3/8” Wood Screws per board. (fig. 13.2) Fig. 13.
Step 13: Floor Board Assembly Part 2 C: Next to (151) Slidenest Floor A place 1 (153) Floor A followed by 6 (152) Floors. Make sure all boards are evenly spaced and the last (152) Floor is flush to the front of (060) SL Panel. (fig. 13.3, 13.4 and 13.5) D: Attach the 7 unfastened floor boards to (071) Front Floor, (085) Floor Joist and (073) Back Floor with 6 (S20) #8 x 1-3/8” Wood Screws per board. (fig. 13.5) Fig. 13.3 Fig. 13.
Step 14: Attach Front Top A: Attach (127) Front Top to (040) Wall Cafe Window Panel with 2 (WB9) 5/16 x 2-1/8” Wafer Bolts (with flat washer and t-nut) as shown in fig. 14.1 and 14.2. B: Attach (127) Front Top to (082) SL Post with 1 (S15) #8 x 1-3/4” Wood Screw in the top hole. (fig. 14.1 and 14.2) Fig. 14.1 082 127 040 Flush S15 127 Fig. 14.2 Leave this hole empty.
Step 15: Attach Transom Front and Back Part 1 A: Place (222) F Transom on top of (082) SL Post and (040) Cafe Wall Window Panel, behind (127) Front Top so the outside edge is flush to the outside edge of (082) SL Post as shown in fig. 15.1 and 15.2. If the space is too tight, loosen the bolt at the front of the assembly, as shown in fig. 15.2. B: From inside the assembly attach (222) Transom Panel Front to (127) Front Top with 3 (S15) #8 x 1-3/4” Wood Screws. (fig. 22.
Step 15: Attach Transom Front and Back Part 2 D: Place (223) B Transom on top of (050) Narrow Window Panel, behind (100) Back Top so the outside edge is flush to the outside edge of (050) Narrow Window Panel as shown in fig. 15.3 and 15.4. E: From inside the assembly attach (223) B Transom to (100) Back Top with 2 (S15) #8 x 1-3/4” Wood Screws. (15.4) 223 Fig. 15.3 050 Back 100 Front Fig. 15.
Step 16: Roof Support Assembly Part 1 A: Attach (180) Roof Support to (181) Roof Support Left at peak using 1 (S4) #8 x 3” Wood Screw. (fig. 16.1) B: Place (182) Top Post Right and (183) Top Post Left on the ground with the notched out side facing up. Place (184) SW Top over (182) and (183) Top Post Right and Left so the notches fit together. (fig. 16.2 and 16.
Step 16: Roof Support Assembly Part 2 D: Place Roof Support Assembly on the ground with the front facing down then measure 12” from the centre of either bolt hole and 2” down from the top of (184) SW Top and attach 1 (185) Sunburst with 2 (S15) #8 x 1-3/4” Wood Screws to the outside of the assembly. (fig. 16.4 and 16.5) Fig. 16.4 Inside View 180 181 184 2” 185 12” 185 Fig. 16.
Step 16: Roof Support Assembly Part 3 E: Place (186) Centre Gable on (185) Sunburst, tight to the top of (184) SW Top so the tip is centred at the peak of the Roof Support Assembly. (fig. 16.6) F: Place 1 (187) Side Gable tight to each side of (186) Centre Gable so they are tight to the top of (184) SW Top. (fig. 16.
Step 17: Gable Angle Support Assembly Part 1 A: Attach (190) Right Gable Angle to (191) Left Gable Angle at peak using 1 (S4) #8 x 3” Wood Screw. (fig. 17.1) B: In the bolt holes on (192) Gable Bottom tap in 2 - 5/16” t-nuts then place (192) Gable Bottom on (190) Right Gable Angle and (191) Left Gable Angle so it is flush to the outside edges of the boards. (fig. 17.2) C: Flip the assembly over so the large counter sunk holes are facing up.
Step 17: Gable Angle Support Assembly Part 2 D: Measure 8-1/2” from the centre of either bolt hole then place 1 (185) Sunburst on (192) Gable Bottom making sure it is flush to the bottom of (192) Gable Bottom, then attach with 2 (S15) #8 x 1-3/4” Wood Screws to the outside of the assembly. (fig. 17.4 and 17.5) 8-1/2” Fig. 17.4 Inside View 185 190 Notice bolt side facing out 192 191 Flush Fig. 17.
Step 17: Gable Angle Support Assembly Part 3 E: Place (186) Centre Gable on (185) Sunburst, tight to the top of (192) Gable Bottom so the tip is centred at the peak of the Gable Angle Support Assembly. (fig. 17.6) F: Place 1 (187) Side Gable tight to each side of (186) Centre Gable so they are tight to the top of (192) Gable Bottom. (fig. 17.6) G: Attach (186) Centre Gable with 4 (S20) #8 x 1-3/8” Wood Screws and both (187) Side Gables with 3 (S20) #8 x 1-3/8” Wood Screws per board as shown in fig.17.
Step 18: Roof Spacer Assembly A: Attach 1 (200) Roof Spacer to another at the peak using 1 (S4) #8 x 3” Wood Screw. Notice the pilot holes are towards the bottom of the board. (fig. 18.1) B: Make sure the assembly is square. S4 Fig. 18.1 Notice hole position 200 Hardware Wood Parts 2x 200 Roof Spacer FSC 5/4 x 6 x 32-1/4” 1x S4 #8 x 3” Wood Screw 57 support@solowavedesign.
Step 19: Small and Large Roof Assemblies Part 1 A: Connect 1 (210) Large Roof Panel to a second (210) Large Roof Panel so the one panel overlaps the other and the inside angle is square and tight. Attach panels together with 3 (S15) #8 x 1-3/4” Wood Screws per panel. (fig. 19.1 and 19.2) 210 Fig. 19.1 Notice overlap is flush 210 S15 Fig. 19.2 210 210 S15 Wood Parts 2x 210 Large Roof Panel FSC 1-1/4 x 31-3/4 x 41” Hardware 6x S15 #8 x 1-3/4” Wood Screw 58 support@solowavedesign.
Step 19: Small and Large Roof Assemblies Part 2 B: Connect 1 (211) Small Roof Panel to a second (211) Small Roof Panel so the one panel overlaps the other and the inside angle is square and tight. Attach panels together with 3 (S15) #8 x 1-3/4” Wood Screws per panel. (fig. 19.3 and 19.4) Fig. 19.4 211 211 S15 Fig. 19.3 211 211 S15 Wood Parts 2x 211 Small Roof Panel FSC 1-1/4 x 31-3/4 x 32-1/2” Hardware 6x S15 #8 x 1-3/4” Wood Screw 59 support@solowavedesign.
Step 19: Small and Large Roof Assemblies Part 3 C: Place Roof Spacer Assembly from Step 18, on top of the Small Roof Assembly, flush to the edge as shown in fig. 19.5. D: Measure 1/2” in from the edge and 7” up from the bottom of each (211) Small Roof Panel and mark. Follow with 11” up from the first mark and then 11” up from the second mark. Pre-drill with a 1/8” drill bit at all 6 marks. (fig. 19.6 and 19.
Step 20: Attach Roof Support Assemblies Part 1 A: Place Roof Support Assembly, from Step 16, Part 3, on the top of (043) SW Side Panel, flush to the front. (fig. 20.1 and 20.2) B: Attach (182) Top Post Right to (050) Narrow Window Panel with 1 (S3) #8 x 2-1/2” Wood Screws and to (223) B Transom with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 20.1 and 20.
Step 20: Attach Roof Support Assemblies Part 2 D: Make sure the distance between (040) Wall Cafe Window Panel and (050) Narrow Window Panel is 36”. (fig. 20.3 and 20.4) E: On the Slide Side, attach Gable Angle Support Assembly, from Step 17, Part 3, to the ends of (127) Front Top, (040) Wall Cafe Window Panel, (100) Back Top and (050) Narrow Window Panel with 2 (S4) #8 x 3” Wood Screws per side as shown in fig. 20.4.
Step 20: Attach Roof Support Assemblies Part 3 F: From inside the assembly attach (191) Left Gable Angle to (050) Narrow Window Panel and (190) Right Gable Angle to (040) Cafe Wall Window Panel using 1 Corner Panel Bracket with 3 (S13) #6 x 5/8” Pan Screws per side. (fig. 20.5) Fig. 20.5 190 191 Flush S13 x 3 per bracket 050 Corner Panel Bracket (one hidden) 040 Hardware 6x S13 #6 x 5/8” Pan Screw 63 Other Parts 2 x Corner Panel Bracket support@solowavedesign.
Step 21: Attach Roof Assemblies to Fort Part 1 A: With 2 people on the ground and at least 1 person in the fort, lift the Small Roof Assembly with Roof Spacer Assembly, from Step 19, Part 3, up and over the Back side of the fort. Guide the Roof Assembly onto the fort so the Roof Spacer Assembly sits flush to the top and outside edges of both (222) F Transom and (223) B Transom. (fig. 21.1) B: Attach each (200) Roof Spacer to (222) F Transom and (223) B Transom with 2 (S4) #8 x 3” Wood Screws per side.
Step 21: Attach Roof Assemblies to Fort Part 2 C: Make sure the Small Roof Assembly lays flat on the Gable Angle Support Assembly and it overhangs by 2”. (fig. 21.2) D: Measure 3/4” from the edge, 5” up from the ends of both panels and 5” down from the peak on each panel, pre-drill with a 1/8” drill bit then attach the Small Roof Assembly to the Gable Angle Support Assembly with 2 (S3) #8 x 2-1/2” Wood Screws per side, as shown in fig. 21.2. Fig. 21.
Step 21: Attach Roof Assemblies to Fort Part 3 E: With 2 people on the ground and at least 1 person in the fort, lift the Large Roof Assembly, from Step 19, Part 1, up and over the Back side of the fort. Guide the Roof Assembly onto the fort so it sits on top of the Roof Support Assembly, (222) F Transom and (223) B Transom and Roof Spacer Assembly. (fig. 21.3) F: Make sure the Large Roof Assembly lays flat on the Roof Support Assembly and it overhangs by 2”. (fig. 21.
Step 22: Lower Crowsnest Assembly Part 1 A: Attach 1 (330) Crowsnest Side flush to the inside edge of the panel post on both (050) Narrow Window Panel and (040) Wall Cafe Window Panel using 3 (S15) #8 x 1-3/4” Wood Screws per side. Each (330) Crowsnest Side must sit tight to top of (152) Floor. Notice pilot holes towards bottom of boards. (fig. 22.1 and 22.2) Fig. 22.1 050 Fig. 22.
Step 22: Lower Crowsnest Assembly Part 2 B: Attach 4 (333) Crowsnest Joists to (332) Crowsnest Front and (331) Crowsnest Back using 4 (S3) #8 x 2-1/2” Wood Screws per joist as shown in fig. 22.3. C: Flush to the bottom of each (330) Crowsnest Side attach assembly just built using 3 (S15) #8 x 1-3/4” Wood Screws per board. (332) Crowsnest Front is to face out and (331) Crowsnest Back is to face towards the fort. (fig. 22.4) S3 x 8 Fig. 22.3 333 331 Notice holes used 332 S3 x 8 330 Fig. 22.
Step 23: Upper Crowsnest Assembly Part 1 A: Attach (340) Crowsnest SL Top to 2 (341) Crowsnest Uprights using 2 (G8) 5/16 x 2” Hex Bolts (with lock washer, flat washer and t-nut), making sure the notched ends are facing out. (fig. 23.1) Fig. 23.
Step 23: Upper Crowsnest Assembly Part 2 B: Attach the bottom of each (341) Crowsnest Upright to (332) Crowsnest Front using 2 (G8) 5/16 x 2” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 23.2 and 23.3) Fig. 23.2 Fig. 23.3 341 5/16” T-Nut 341 5/16” Flat Washer 5/16” Lock Washer 332 G8 Hardware 2 x G8 5/16 x 2” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut) 70 support@solowavedesign.
Step 24: Crowsnest Floor Assembly Part 1 A: Make sure the frame is level, then attach 1 (334) Crowsnest Gusset flush to the top of (332) Crowsnest Front, to each of the interior (333) Crowsnest Joists on the outside of each joist using 1 (S3) #8 x 2-1/2” Wood Screw per Gusset. (fig. 24.1 and 24.2) B: Attach each (334) Crowsnest Gusset to (332) Crowsnest Front in the remaining holes using 2 (S4) #8 x 3” Wood Screws per gusset. (fig. 24.1 and 24.2) 333 Fig. 24.
Step 24: Crowsnest Floor Assembly Part 2 C: Measure 9-3/4” from inside edge of (071) Front Floor and attach (060) SL Panel to 1 (334) Crowsnest Gusset using 2 (S4) #8 x 3” Wood Screws as shown in fig. 24.3 D: Measure 14” from screws in Step C and attach (060) SL Panel to the second (334) Crowsnest Gusset using 2 (S4) #8 x 3” Wood Screws as shown in fig. 24.3. Fig. 24.
Step 24: Crowsnest Floor Assembly Part 3 E: Lay down (344) Crowsnest Gap flush to front of (332) Crowsnest Front and (345) Crowsnest Floor flush to back of (331) Crowsnest Back. In between (344) and (345) place 2 (346) Crowsnest Floor. (fig. 24.4 and 24.5) F: Attach the floor and gap boards to each (333) Crowsnest Joist using 6 (S20) #8 x 1-3/8” Wood Screws per board. (fig. 24.5) Fig. 24.4 Fig. 24.
Step 25: Crowsnest Wall Assembly Part 1 A: Place 1 (348) Crowsnest Face on the front of each (341) Crowsnest Upright, flush to the outside edges and attach from inside the fort using 3 (S15) #8 x 1-3/4” Wood Screws per board as shown in fig. 25.1, 25.2 and 25.3. Fig. 25.1 Fig. 25.2 S15 341 341 Fig. 25.3 S15 348 S15 Flush 348 Inside View Hardware Wood Parts 2x 348 Crowsnest Face FSC 2 x 4 x 27-3/4” 341 6x S15 #8 x 1-3/4” Wood Screw 74 support@solowavedesign.
Step 25: Crowsnest Wall Assembly Part 2 B: Place 1 (347) Crowsnest Wall in between (330) Crowsnest Side and (341) Crowsnest Upright, flush to front of each (348) Crowsnest Face and tight to the floor boards. Attach (330) Crowsnest Sides from outside to (347) Crowsnest Wall in the top hole and to (333) Crowsnest Joist in the bottom hole using 2 (S15) #8 x 1-3/4” Wood Screws per side and from the inside with 1 (S15) #8 x 1-3/4” Wood Screw per side. (fig. 25.4, 25.5 and 25.
Step 25: Crowsnest Wall Assembly Part 3 D: Flush to the front and top of each (340) Crowsnest SL Top attach 1 (330) Crowsnest Side using 3 (S15) Wood Screws per side. Notice the pilot holes are towards the top of the boards. (fig. 25.7, 25.8 and 25.9) E: Attach the other end of each (330) Crowsnest Side to (050) Narrow Window Panel and (040) Wall Cafe Window Panel using 3 (S15) #8 x 1-3/4” Wood Screws per side. (fig. 25.7, 25.8 and 25.9) Fig. 25.8 050 Fig. 25.
Step 25: Crowsnest Wall Assembly Part 4 F: In between (347) Crowsnest Wall and (050) Narrow Window Panel evenly space and attach 2 (166) Wall Boards to both (330) Crowsnest Sides using 4 (S20) #8 x 1-3/8” Wood Screws per board. (166) Wall Boards are to be tight to the floor board and bevelled edges at the top and facing out. (fig. 25.10 and 25.
Step 26: Attach Heavy T-Bracket to Fort A: Attach Heavy T-Bracket to (044) SW Wall using 2 (WB7) 5/16 x 3” Wafer Bolts (with flat washer and t-nut). (fig. 26.1 and 26.2) Fig. 26.1 044 Fig. 26.2 Swing Side WB7 044 5/16” Flat Washer 5/16” T-Nut Heavy T-Bracket Hardware 2x WB7 5/16 x 3” Wafer Bolt (5/16” flat washer, 5/16” t-nut) 78 Other Parts 1 x Heavy T-Bracket support@solowavedesign.
Step 27: Swing Beam Assembly A: Attach 6 Heavy Duty Swing Hangers to (260) Engineered SW Beam using 2 (G13) 5/16 x 6-1/8” Hex Bolt (with 2 flat washers, plastic formed washer and lock nut) per swing hanger, as shown in fig. 27.1. B: Attach 1 Quick Clip to each Heavy Duty Swing Hanger. (fig. 27.2) Fig. 27.1 Fig. 27.
Step 28: Swing Post Assembly Part 1 Note: Keep all bolts from Step 28 series loose until start of Step 30 A: Place (270) SW Block Angle on top of (271) Block SW and attach 2 Heavy L-Brackets on top of (270) SW Block Angle feeding 2 (G17) 3/8 x 6” Hex Bolts (with 2 flat washers, plastic formed washer and lock nut) through both boards as shown in fig. 28.1 and 28.2. B: Attach 3 (WB7) 5/16 x 3” Wafer Bolts (with flat washer and t-nut) to all three holes in each (272) SW Post as shown in fig. 28.3 and 28.4.
Step 28: Swing Post Assembly Part 2 D: Attach Big Backyard plaque to centre of (260) Engineered SW Beam (over top of t-nut) using 4 (S18) #6 x 1” Wood Screws. (fig. 28.6) E: Place (260) Engineered SW Beam on Heavy T-Bracket and attach to fort with 1 (G17) 3/8 x 6” Hex Bolt (with 2 flat washers, plastic formed washer and lock nut) and 1 (G18) 3/8 x 9” Hex Bolt (with 2 flat washers, plastic formed washer and lock nut) as shown in fig. 28.7 and 28.8. Fig. 28.
Step 29: Attach Cross Support Pre-drill all holes using a 3/16” drill bit before installing the lag screws. A: Check to make sure the (260) Engineered SW Beam is level and the bottom of the beam to the ground measures 85”. (fig. 29.1) B: To adjust for uneven ground, raise or lower the (280) Support Cross on the (272) SW Post. Make sure the Support Cross is level prior to attaching with the lag screws. (fig. 29.2) Fig. 29.1 Fig. 29.2 360 Fig. 38.
Step 30: Final Swing Post Assembly Pre-drill all holes using a 3/16” drill bit before installing the lag screws. Note: Tighten all bolts from Step 28 series before installing lag screws. A: Attach 1 (LS9) 5/16 x 4-3/4” Lag Screw (with flat washer) into each (272) SW Post, as shown in fig. 30.1. B: Attach 1 (LS9) 5/16 x 4-3/4” Lag Screw (with flat washer) into remaining hole of the Heavy G-Bracket into (260) Engineered SW Beam. (fig. 30.1) Fig. 30.
Step 31: Attach Swings A: Using 1 Threaded Clip per chain, join 1 Long Swing Chain to each side of the swing belt seat. Make sure to close the Threaded Clip tightly using an adjustable wrench. (fig. 31.1 and 31.2). B: Using 1 Threaded Clip per chain, join the Short Swing Chain to the Acro Bar and Acro Handle. Make sure to close the Threaded Clip tightly using an adjustable wrench. (fig. 31.2 and 31.3) C: Attach the other end of the swing chains to the Quick Clips attached to the swing hangers. (fig. 31.
Step 32: Attach Swing End Ground Stakes A: In the 2 places shown in fig. 32.1 drive the Rebar Ground Stakes 13” into the ground against the boards. Be careful not to hit the washer while hammering stakes into the ground as this could cause the washer to break off. B: Attach ground stakes to (272) SW Posts using 1 (S7) #12 x 2” Pan Screw per ground stake as shown in fig. 32.1. C: After driving stakes into the ground, check for sharp edges caused by the impact of the hammer.
Step 33: Attach Access Ladder Rockwall Assembly Pre-drill all holes using a 1/8” drill bit before installing the Wafer Lags A: Remove (030) Board Access from the Access Ladder Rockwall, previously assembled in Step 3. Set the board and screws aside, they will be re-attached. (fig. 33.2) B: Place the Access Ladder Rockwall on the Back side of the fort and attach to (073) Back Floor with 1 (WL3) 1/4 x 1-3/8” Wafer Lag Screw (with flat washer) in each Swing Bracket. (fig. 33.1, 33.2 and 33.3).
Step 34: Attach Steel Hand Grips to Fort Pre-drill all holes using a 1/8” drill bit before installing the Wafer Lags A: Measure 6” from the top of (025) Top Ladder on each (050) Narrow Window Panel and attach 1 Steel Hand Grip per panel with 2 (WH2) #12 x 1” Wafer Screw (with flat washer) per Steel Hand Grip. (fig. 34.1, 34.2 and 34.3) Fig. 34.1 Fig. 34.2 3/16” Flat Washer WH2 050 Fig. 34.
Step 35: Attach Middle Arch to Fort A: Measure 23-3/4” from the top of (025) Top Ladder on each (050) Narrow Window Panel and attach (370) Middle Arch with 4 (S15) #8 x 1-3/4” Wood Screws. (fig. 35.1 and 35.2) Fig. 35.1 Fig. 35.2 S15 050 050 370 23-3/4” 025 Wood Parts 1x 370 Middle Arch FSC 5/4 x 5 x 36-1/4” Hardware 4x S15 #8 x 1-3/4” Wood Screw 88 support@solowavedesign.
Step 36: Attach Flower Boxes A: On the front of the assembly place 1 Flower Box under each window and attach to (040) Wall Cafe Window Panel with 2 (S13) #6 x 5/8” Pan Screws per Flower Box. (fig. 36.1, 36.2 and 36.3) Fig. 36.1 040 Front Fig. 36.3 S13 Flower Box Fig. 36.2 040 Hardware 4x S15 #6 x 5/8” Pan Screw 89 Other Parts 2 x Flower Box support@solowavedesign.
Step 37: Table Top Assembly A: On the outside of the assembly place (080) Table Top in the opening of (040) Cafe Wall Window Panel, tight to the bottom half of the opening and tight to the corner of the panels, as shown in fig. 37.1 and 37.2. From the top of the assembly attach (080) Table Top to (040) Cafe Wall Window Panel with 2 (S3) #8 x 2-1/2” Wood Screws as shown in fig. 37.2.
Step 38: Attach Slide to Fort Note: Pre-drill all holes using a 1/8” drill bit before installing the pan screws. A: Place Slide centred in the opening between (122) Posts. (fig. 38.1 and 38.2) B: Attach slide to fort through the floor boards and into (126) SL End using 3 (S7) #12 x 2” Pan Screws. (fig. 38.1 and 38.2) Fig. 38.1 122 Slide 122 Front Fig. 38.2 122 Floor Boards S7 122 Slide 126 Hardware 3x S7 #12 x 2” Pan Screw 91 Other Parts 1 x Slide support@solowavedesign.
Step 39: Attach Cafe Bench to Fort A: Centre Cafe Bench from Step 1 on the bottom of (060) SL Panel. (fig. 39.1 and 39.2) B: Attach (012) Bench Base Cafe to (060) SL Panel with the previously attached 4 Corner Brackets using 1 (S10) #8 x 1” Pan Screw per bracket. (fig. 39.2 and 39.3) Note: The inside Corner Brackets sit flush to the top and the outside Corner Brackets sit flush to the bottom of (012) Bench Base Cafes as shown in fig. 39.2. Fig. 39.1 Fig. 39.
Step 40: Crowsnest Bottom Assembly A: Centre (401) Bottom Board on (332) Crowsnest Front, tight to the top of the floor boards then attach to each (348) Crowsnest Face using 2 (S3) #8 x 2-1/2” Wood Screws per side. (fig. 40.1 and 40.2) B: Place (342) Crowsnest Short in between both (341) Crowsnest Uprights, tight to the floor boards then attach to (401) Bottom Board with 6 (S15) #8 x 1-3/4” Wood Screws as shown in fig. 40.2 and 40.3. Fig. 40.1 342 Fig. 40.2 401 Floor Boards S3 Tight 332 S3 Fig.
Step 41: Crowsnest Front Wall Assembly A: Centre (410) Centre Board between both (341) Crowsnest Uprights and measure 1-1/2” up from the floor boards then attach to (340) Crowsnest SL Top and (342) Crowsnest Short with 4 (S20) #8 x 1-3/8” Wood Screws as shown in fig. 41.1 and 41.2.
Step 42: Attach Steering Wheel A: Place (165) Steering Wheel Dash on top of (340) Crowsnest SL Top, centred over (410) Centre Board and attach to (340) Crowsnest SL Top with 2 (S3) #8 x 2-1/2” Wood Screws and to (410) Centre Board with 2 (S20) #8 x 1-3/8” Wood Screws. (fig. 42.1 and 42.2) B: Pre-drill with a 1/8” drill bit, then attach Steering Wheel to (410) Centre Board and (165) Steering Wheel Dash with 1 (WL5) 1/4 x 2-1/2” Wafer Lag (with flat washer). (fig. 42.1 and 42.3) Fig. 42.
Step 43: Attach Telescope A: On the front, outer corner of the Crowsnest pre-drill with a 1/8” drill bit then attach Telescope to (340) Crowsnest SL Top and (330) Crowsnest Side with 2 (S15) #8 x 1-3/4” Wood Screws. (fig. 43.1 and 43.2) Fig. 43.1 S15 Fig. 43.2 Telescope 330 340 Hardware 2x S15 #8 x 1-3/4” Wood Screw 96 Other Parts 1 x Telescope support@solowavedesign.
Step 44: Attach SW Table Top A: In the opening of (060) SL Panel attach (510) SW Table Top, tight to the corners of the panel opening, ledge facing in, with 3 (S3) #8 x 2-1/2” Wood Screws as shown in fig. 44.1 and 44.2. Fig. 44.1 060 S3 Fig. 44.2 Tight 060 Outside View Tight 510 Warning! Check entire play center for bolts protruding beyond T-Nuts. Use extra washers to eliminate this condition.
Final Step:NAME Attach I.D. Plaque STEP # STEP ATTACH THIS WARNING & I.D. PLAQUE TO A PROMINENT LOCATION ON YOUR PLAY EQUIPMENT! (Fort or Swing Post) This provides warnings concerning safety and important contact information. A Tracking Number is provided to allow you to get critical information or order replacement parts for this specific model.
NOTES 99 support@solowavedesign.
BIG BACKYARD Consumer Registration Card First Name Initial Last Name Street Apt. No.
