Specifications

9
RS-232 CONTROL
Serial Port: The 9-pin Sub-D (male) connector on the equalizer rear panel provides the RS-232 compatible serial interface signals used
for computer control. The Serial Port transmits serial data on pin 3 (TxD), receives serial data on pin 2 (RxD), and provides a ground on
Pin 5. The Data Terminal Ready (DTR) & Request To Send (RTS) output signals are connected to a positive voltage source (through a
resistor) and are always asserted when the equalizer power is on.
NOTE: The Serial Port will also transmit commands which are received
via the Logic Inputs
pin #1 = not used
pin #2 = Receive Data (RxD) input
pin #3 = Transmit Data (TxD) output
pin #4 = Data Terminal Ready (DTR) output
pin #5 = ground
pin #6 = not used
pin #7 = Request To Send (RTS) output
pin #8 = not used
pin #9 = not used
serial port
54321
9876
The equalizer only requires receive data (pin 2), transmit data (pin 3), and signal ground (pin 5) to be connected for successful data
communications (see cable diagram below). However, the PC may require that signals be present on the data set ready, clear to send, or
carrier detect inputs, as well as the receive data, transmit data, and signal ground pins. Success or failure depends entirely on the actual
computer hardware and software being used. When trying to solve an interfacing problem, the most important thing to remember is that an
output of one device should connect to one or more inputs of the other device, and that two outputs should never be connected together.
Also, keep in mind that the RS-232 specification calls for the cable length to be no greater than 50 feet (although it is not unusual to be
able to operate over distances of 150 to 250 feet), and the connectors must be of the appropriate gender (male or female) to mate
properly. For best results, a shielded cable should be used, with the shield connected to signal ground. Since the equalizer serial interface
ground is also tied (indirectly) to the analog signal ground, undesirable ground loops may occur when the equalizer is connected to a PC (if
the system grounding is not carefully designed). For best performance, the PC ground and the chassis ground of the equalizer should be
at the same potential, and the PC should get AC power from the same source as the equalizer (and any other audio equipment which is
connected to the equalizer)
.
Serial Port Data Communications Parameters: The equalizer communicates through the Serial Port at the factory selected rate of 9600
bits per second, with 8 data bits, 1 stop bit, and no parity. The equalizer utilizes a subset of the standard 7-bit ASCII character set. The
eighth data bit of each character (the most significant bit) should always be 0. The computer should not echo the characters it receives.
The computer should not be set for either hardware (DTR) or software (XON/XOFF) flow control. The baud rate may be changed to either
2400 or 19,200 bits per second by means of the rear panel Baud Rate DIP switches.
Link Port Connections: The 9-pin Sub-D (female) connector on the equalizer rear panel provides the RS-232 compatible serial interface
signals used for linking multiple ADVANTAGE
®
products within a system. The Link Port of one device simply connectes to the Serial Port
of the next device, and so forth (see diagram below). Link cables are available as an option (Biamp #909-0057-00).
NOTE: All but the
final device in a system should have its ‘last’ switch down (see Rear Panel: Baud Rate on pg. 3). The Link Port will also transmit
commands which are received via the Logic Inputs.
pin #1 = not used
pin #2 = Transmit Data (TxD) output
pin #3 = Receive Data (RxD) input
pin #4 = not used
pin #5 = ground
pin #6 = not used
pin #7 = not used
pin #8 = not used
pin #9 = not used
link port
12345
6789
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
CD
RxD
TxD
DTR
DSR
RTS
CTS
RI
gnd
PC
(shield)
serial port
male female
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
n/a
RxD
TxD
DTR
gnd
n/a
RTS
n/a
n/a
EQ
serial port
female male
Serial Cable
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
n/a
TxD
n/a
n/a
n/a
n/a
n/a
gnd
EQ
(shield)
link port
female male
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
n/a
RxD
TxD
DTR
gnd
n/a
RTS
n/a
n/a
unit 2
serial port
female male
Link Cable
RxD