ORDER NO. MD0411549C3 CD Stereo System SA-AK330GC SA-AK330GN Colour (S)... Silver Type Specifications n AMPLIFIER SECTION Aux RMS output power Phone jack THD 10%, both channels driven Terminal 1 kHz n CASSETTE DECK SECTION 90 W per channel (5 Ω) (Low channel) 10 kHz 90 W per channel (5 Ω) Total Bi-Amp power 360 W PMPO (For GC only) 3300 W n FM/AM TUNER, TERMINALS SECTION Tape speed AC erase 100 kHz 4.8 cm/s NORMAL 2.5 µV (IHF) 2.
SA-AK330GC / SA-AK330GN CD 44.1 kHz Decoding Dimensions (W x H x D) 16 bit linear Digital filter Mass 8 fs D/A converter 250 x 330 x 341 mm 7.
SA-AK330GC / SA-AK330GN 16.2. (B) Main (Tuner) Circuit 60 18 Wiring Connection Diagram 82 16.3. (B) Main Circuit 61 19 Illustration of IC 痴, Transistors and Diodes 83 16.4. (C) Panel Circuit 66 20 Terminal Function of IC 痴 84 16.5. (D) Transformer Circuit, (E) CD Detect Circuit, (F) Spindle Position Circuit & (G) CD Loading Circuit 16.6. (H) Power Circuit 69 16.7. (I) Deck Circuit & (J) Deck Mechanism Circuit 70 17 Printed Circuit Board 20.1.
SA-AK330GC / SA-AK330GN 1 Before Repair and Adjustment Disconnect AC power, discharge Power Supply Capacitors C5820 and C5840 through a 10Ω, 5W resistor to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices. After repairs are completed, restore power gradually using a variac, to avoid overcurrent. Current consumption at AC 220 - 240V, 50/60 Hz in NO SIGNAL mode (volume min at CD mode) should be ~350mA (For GC only).
SA-AK330GC / SA-AK330GN 3 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components.
SA-AK330GC / SA-AK330GN 5 Handling Precautions For Traverse Deck The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup). · Handling of traverse deck (optical pickup) 1. Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive to electrical shock. 2.
SA-AK330GC / SA-AK330GN 6 Precaution of Laser Diode Caution : This product utilizes a laser diode with the unit turned "ON", invisible laser radiation is emitted from the pick up lens. Wavelength : 780 nm Maximum output radiation power from pick up : 100 µW/VDE Laser radiation from pick up unit is safety level, but be sure the followings: 1. Do not disassemble the optical pick up unit, since radiation from exposed laser diode is dangerous. 2. Do not adjust the variable resistor on the pick up unit.
SA-AK330GC / SA-AK330GN 7 Accessories Remote Control FM Antenna AC Cord (For GN only) AC Cord (For GC only) AM Loop Antenna 8
SA-AK330GC / SA-AK330GN 8 Operation Procedures 9
SA-AK330GC / SA-AK330GN 10
SA-AK330GC / SA-AK330GN 9 Disassembly and Assembly of Main Component “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. 2. For reassembly after operation checks or replacement, reverse the respective procedures. Special reassembly procedures are described only when required. 3.
SA-AK330GC / SA-AK330GN 9.2. Gear for servicing (jig) Information 1. This unit has a gear which is used for checking items (Open/Close of disc tray, up/down operation of traverse unit by manually) when servicing. 2. For preparation of gear (for servicing), perform the procedures as follows. 3. In case of re-servicing the same set, the “gear for servicing” may has been taken off because it has been used. The “gear for servicing” must be stored.
SA-AK330GC / SA-AK330GN 9.3. Disassembly of Top Cabinet Step 1 Remove 2 screws at each side and 5 screws at rear panel. Step 2 Lift up both sides of the top cabinet, push the top cabinet towards the rear and remove the top cabinet. 9.4. Disassembly of CD Lid (The CD changer unit can be removed after the CD Lid is removed) · Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet · Opening the disc tray automatically (Using Power Supply) Step 1 Connect the AC power cord.
SA-AK330GC / SA-AK330GN Step 2 Release the 2 claws, and then remove the CD lid cover. Step 6 Press the POWER button to turn the power off. · [Opening the disc tray manually (Using service tools)] Step 3 Repeat Step 2 but rotate the gear tools in anti-clockwise direction. Step 1 Insert the gear tool into the hole on the underside of CD chassis and then rotate in the direction of arrow. The disc tray will be opened. Step 4 The disc tray will be closed.
SA-AK330GC / SA-AK330GN 9.5. Disassembly of Rear Panel · Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet Step 1 Remove 7 screws and disconnect wire CN2810 (Fan) at rear cabinet as shown. 9.6. Disassembly of CD Mechanism Unit · Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet Step 1 Remove one screw at rear panel. Step 2 Detach the FFC wires (CN2801 & CN2805). Step 4 Remove 4 screws. Step 5 Remove the CD chassis. Step 6 Lay the CD mechanism unit as shown.
SA-AK330GC / SA-AK330GN 9.7. Disassembly of Main P.C.B. · Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet · Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid · Follow the (Step 1) of Item 9.5 - Disassembly of Rear Panel · Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit Step 1 Disconnect FFC wires CN2803 & CN2806 from Main P.C.B. 9.8. Step 2 Lift up Main P.C.B. by disconnecting connectors CN5800 & CN5801 as arrow shown above.
SA-AK330GC / SA-AK330GN · Replacement of the Power Amplifier IC/ Voltage Regulator Step 1 Remove 2 screws fixed to the Power Amplifier IC and 1 screw to Voltage Regulator. Step 3 Unsolder the terminals of Power Amp IC, transistor and replace the components. Step 4 Fix back the cut portion with a screw as shown. Step 2 Break the joint with a metal cutter as shown below. 9.9. Disassembly of Transformer P.C.B. · Follow the (Step 1) - (Step 2) of Item 9.
SA-AK330GC / SA-AK330GN 9.10. Disassembly of Front Panel Unit · Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet · Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid · Follow the (Step 1) of Item 9.5 - Disassembly of Rear Panel · Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit Step 1 Lay the unit as shown below. Step 2 Release 2 claws at bottom and 2 claws each side, draw the front panel ass’y forward. Step 4 Remove 10 screws.
SA-AK330GC / SA-AK330GN Step 7 Unsolder the motor terminals. Step 8 Remove Deck Mechanism P.C.B. 9.12. CD Mechanism Main Component Replacement Procedures · Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet · Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid · Follow the (Step 1) - (Step 6) of Item 9.6 - Disassembly of CD Mechanism Unit 9.12.1. Replacement of the Traverse Deck Step 1 Remove the CD changer unit.
SA-AK330GC / SA-AK330GN Step 6 Lift up the traverse deck ass’y. Step 10 Remove the FFC board from the connector, and then remove the CD Servo P.C.B. Step 7 Remove the traverse deck ass’y from the timing lever. Caution: When removing or inserting the traverse deck avoid touching the OPU lens and pressing onto the turntable. Step 11 Remove the pin. Step 8 Remove 3 screws. Step 9 Unsolder the motor terminals (4 points). Step 12 Release the claw, and then remove the traverse deck ass’y.
SA-AK330GC / SA-AK330GN Note: Step 1 Install the traverse deck ass’y to the timing lever. Be careful not to lose the 3 floating spring because those will also be removed on removal of the traverse deck ass’y. Step 2 Align the boss of traverse deck ass’y with the slot of traverse cam gear. · Installation of the CD Servo P.C.B. after replacement Step 1 Connect the FFC board. Step 2 Install the CD servo P.C.B. in the traverse deck ass’y. Step 3 Remove 3 screws. Step 4 Solder.
SA-AK330GC / SA-AK330GN Step 5 With pressing the claw (B) in the direction of arrow (1), force the connection lever in the direction of arrow (2). 9.12.2. Replacement for the Disc Tray Step 1 Remove 4 screws. Step 2 Remove the upper plate. Step 3 Remove 3 screws. Step 6 Insert the gear with hexagonal wrench into the hole. Step 4 With lifting the claw in the direction of (1), draw the CD Detect P.C.B. in the direction of arrow (2). Step 5 Remove the mechanism cover.
SA-AK330GC / SA-AK330GN Step 2 Holding the drive rack not to move, install the disc tray. Step 8 Release the both claws, and then draw the disc tray. Step 3 Align the drive rack with the drive gear. Step 9 With forcing the left guide bar manually because the left guide bar interfers with claw, draw the disc tray. NOTE: Force the right guide bar of tray base manually not to move upwards.
SA-AK330GC / SA-AK330GN 9.12.3. Disassembly and reassembly for mechanism base drive unit Step 1 Remove 3 screws. Step 2 Release the claw, and then remove the gear holder. Step 3 Remove the belt and change gear spring. NOTE: Take care not to lose the change gear spring. Step 6 Install the tray lock spring to hook temporary. Step 4 Remove the pulley gear, change gear and UP/DOWN gear. Step 7 Release the claw, and then remove the tray lock. Step 8 Release the claw, and then remove the rear lock.
SA-AK330GC / SA-AK330GN Step 11 Lift up the left end of spindle base unit in the direction of arrow (1), and then remove the unit in the direction of arrow (2). Step 9 Pressing the claw (B) in the direction of arrow (1), force the connection lever in the direction of arrow (2). Step 10 Move the slide plate 1 to the end of stock side. Step 12 Remove slide plate 1 and slide plate 2.
SA-AK330GC / SA-AK330GN Step 3 Rotate the disc lever in the direction of arrow (1), draw the disc lever. Step 13 Remove the traverse relay gear, traverse cam gear and drive gear. [Dissassembly/reassembly for the spindle base unit] Step 1 Draw the 5 disc spacers. NOTE: Take care not to lose the disc lever spring. Step 2 Pushing the claw, slide the support plate in the direction of arrow, and then remove it. Step 4 Release the 2 claws, and then draw the relay gear B.
SA-AK330GC / SA-AK330GN NOTE: Hold the loading stopper ass’y manually bacause it is flipped by spring. Step 8 Release the 2 claws, and then remove the relay gear A. Step 9 Release the 2 claws, and then remove the spindle shaft. Step 6 Remove the cushion spring. Step 7 Remove the loading stopper ass’y in the direction of arrow. Step 10 Remove the lower spindle spring with tweezers. Step 11 Force the lower hook with thin tip of minus screwdriver.
SA-AK330GC / SA-AK330GN spread the hold bars of loading stopper and remove the UP/DOWN base. [Installation for loading stopper ass’y] Step 1 Align the claw of loading stoppers ass’y with the slot of spindle base. (Caution should be exercised when alignment of claw due to the size of claws.) Step 2 Lower the loading stopper ass’y, and then align the lower spindle with the trapezoid tooth of relay gear A. Step 12 Squeeze the shaft of lower hook, and then draw it.
SA-AK330GC / SA-AK330GN Step 1 Install the traverse cam gear. Step 2 Rotate the traverse cam gear to the direction of arrow. Step 4 Install the slide plate 2 to the mechanism base, and then match to the connection lever. Step 3 Install the drive gear and traverse relay gear. Step 5 Install the slide plate 1 to the mechanism base, and then match to the connection leve and align the trapezoid tooth of traverse relay gear with the slide plate 1.
SA-AK330GC / SA-AK330GN Step 7 Move the slide plate 1 to forward fully. Step 8 Install the rear lock. (The claw should be latched.) Step 9 Install the Spindle Position P.C.B.. (The claw should be latched.) Step 10 Install the tray lock. (The claw should be latched.) Step 11 Remove the tray lock spring from hook,and then latch to the tray lock. Step 12 Install the UP/DOWN gear, change gear, change gear spring, pulley gear and belt in the order of (1) - (5).
SA-AK330GC / SA-AK330GN Step 14 Install the tray base, traverse ass’y, mechanism cover and upper plate. [Operation check after servicing] Check the proper operation of following items with gear and hexagonal screwdriver. 1. Open/close of tray base. 2. Moving the tray base to the stock side. 3. UP/DOWN operation of spindle base unit. 4. UP/DOWN operation of traverse ass’y. 9.12.4. Replacement for the motor ass’y Step 1 Install the belt temporarily. NOTE: Take care not apply the grease to the belt.
SA-AK330GC / SA-AK330GN 9.13. Replacement for the pinch roller ass’y and head block · Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet · Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid · Follow the (Step 1) of Item 9.5 - Disassembly of Rear Panel · Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit · Follow the (Step 1) - (Step 3) of Item 9.10 - Disassembly of Front Panel Unit · Follow the (Step 1) - (Step 5) of Item 9.
SA-AK330GC / SA-AK330GN Step 5 Remove the flywheel R. Step 6 Release the claw of tape side, and then remove the winding lever and spring. Step 7 Remove the flywheel F. [Installation of the belt] Step 1 The boss and marking should be positioned horizontally. Step 4 Remove 3 screws. Step 2 Put the winding belt on the pulley temporarily. Step 3 Install the flywheel F. Step 4 Put the winding belt on the flywheel F.
SA-AK330GC / SA-AK330GN Step 7 Put the capstan belt A temporarily as shown below. Step 10 Remove 3 screws. Step 11 Put the capstan belt B as shown below. Step 8 Put the capstan belt B on the motor ass’y pulley. Step 12 Put the capstan belt A on the motor ass’y pulley. Step 9 Install the sub chassis to the mechanism, and then tighten screws.
SA-AK330GC / SA-AK330GN 9.15. Replacement for the cassette lid ass’y · Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet Step 1 Lift up the lever upward, open the cassette lid ass’y. (For DECK1 and DECK2) Step 2 Push up the cassette lid ass’y in the direction of arrow. (For DECK1 and DECK2).
SA-AK330GC / SA-AK330GN 9.16. Rectification for tape jam problem · Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet Step 1 If a cassette tape cannot be removed from the deck (the tape is caught by the capstan or pinch roller during playback or recording), rotate the flywheel F in the direction of the arrow to remove it. Step 2 Push the lever upward and open the cassette lid ass’y. Remove the cassette tape.
SA-AK330GC / SA-AK330GN 10 Checking for major P.C.B. Note: Checking of all major P.C.Bs (Main P.C.B., Panel P.C.B., Transformer P.C.B., Deck P.C.B., Deck Mechanism P.C.B. and Power P.C.B.) can be carried out using below procedures. For the disassembling procedure, refer Section 9. 10.1. Checking of Main P.C.B. 1. Remove Top Cabinet and Rear Panel. 2. Remove CD Lid. 3. Disassemble CD Mechanism Unit. 4. Connect FFC wires (CN2801 & CN2805) from CD Mechanism Unit.
SA-AK330GC / SA-AK330GN 10.2. Checking of Transformer P.C.B. 1. Remove Top Cabinet and Rear Panel. 2. Remove CD Lid. 3. Disassemble CD Mechanism Unit. 4. Connect FFC wires (CN2801 & CN2805) from CD Mechanism Unit.
SA-AK330GC / SA-AK330GN 10.3. Checking of Panel, Deck & Deck Mechanism P.C.B. 1. Remove Top Cabinet. 2. Remove CD Lid. 3. Disassemble CD Mechanism Unit. 4. Remove volume knob at Front Panel Unit. 5. Disassemble Panel P.C.B. 6. Disassemble Deck Mechanism Unit. 7. Use the extension cable (A) to reconnect (CN1001) Deck P.C.B. and (CN2803) Main P.C.B. 8. Use the extension cable (B) to reconnect (CP6401) Panel P.C.B. and (CN971) Deck Mechanism P.C.B. Service Tools Extension FFC (A) Deck P.C.B. - Main P.C.B.
SA-AK330GC / SA-AK330GN 10.4. Checking of Power P.C.B. 1. Remove Top Cabinet and Rear Panel. 2. Remove CD Lid. 3. Disassemble CD Mechanism Unit. 4. Remove 3 screws at Transformer P.C.B.. 5. Remove 2 screws at heat sink and 1 screw at Power P.C.B. 6. Flip the Power P.C.B. 7. Insulate the Power P.C.B. with insulation material to avoid short circuit. 8. Use the extension cable (A) to reconnect (CN1001) Deck P.C.B. and (CN2803) Main P.C.B. 9. Use the extension cable (B) to reconnect (CP6401) Panel P.C.B.
SA-AK330GC / SA-AK330GN 11 Self-Diagnostic Function 11.1. Self-diagnostic display This unit is equipped with a self-diagnostic display function which, will display an error code corresponding to the problem occuring. Use this function when performing checking maintenance on the unit. 11.2. How to enter the Self-Diagnostic Function 11.3. Cassette Mechanism Test (For error code H01, H02, H03, F01) 1. Press “TAPE, DECK 1/2” to select Deck 2. 2.
SA-AK330GC / SA-AK330GN 3. Press to close the tray. 4. Press “CD DIRECT PLAY (5)” and 5. Press and remove the CD. 6. Press to close the tray. wait until the tray is open. 7. Press “n/STOP” to indicate Error Code. · If several problem exist, error code will change each time when “n/STOP” is pressed. (e.g. F15 → F26 → F16 ....etc). 11.5. To clear all Error code 1. Press and hold button for 5 seconds. 2. FL indicator shows “CLEAR” for 1 second and change to “T”. 11.6.
SA-AK330GC / SA-AK330GN 11.8.3. Power supply related error detection No. 1 Abnormal Items POWER AMP output abnormal Error Display Method of Detection F61 During normal operation, if DCDET becomes ‘L’, normal POWER OFF process shall not be executed, PCNT shall be switched to ‘L’ immediately. GOODBYE shall not be displayed and the error display F61 will be displayed instead. 2 seconds after the F61 display, ECONO shall be set to ‘L’ and FL display shall be turned off.
SA-AK330GC / SA-AK330GN 12 CD Test Mode Function This CD test mode is provided to check CD unit without connecting to changer loading mechanism. This mode shall operate CD PLAY with CD unit being connected only and CD Automatic Alignment result is shown on FL display. 12.1. How to set CD test mode 12.2. CD Automatically Adjustment result indication Under CD test mode, pressing the numeric key ‘0’ on the remote controller will display the auto adjustment result.
SA-AK330GC / SA-AK330GN · It shall move up one counter when the above operations ends. The counter will reset to 00000 when 99999 is reached. · To exit CD aging test mode, press button, the tray will return to its PLAY position and power will be off. 12.4. Micon ROM Checksum and Version Display Mode 1. Functional Summary Display version number and calculated checksum of the micon software. 2. To enter into Micon ROM checksum and Version Display Mode. a.
SA-AK330GC / SA-AK330GN 13 Measurements and Adjustments 13.1. Cassette Deck Section standard value. Bias voltage for Deck 2 Erase voltage for Deck 2 · Measurement Condition 14±4mV (Normal) 80mV (Normal) − Make sure head, capstan and press roller are clean. − Judgeable room temperature 20 ± 5 °C (68 ± 9°F) · Measuring instrument − EVM (DC Electronic voltmeter) − Digital frequency counter · Test Tape − Tape speed QZZCWAT gain adjustment (3 kHz, -10 Fig.2 dB); 13.1.1.
SA-AK330GC / SA-AK330GN 9. Set AM-SG to 520kHz. 10. Receive 520kHz in the unit. 11. Adjust L2602 (OSC) so that the EVM-DC value is with 1.1±0.5V. Fig.6 13.2.2. AM RF Adjustment 1. Connect the instrument as shown in Fig. 7. 2. Set the unit to AM mode. 3. Set AM-SG to 520kHz. 4. Receive 520kHz in the unit. 5. Adjust Z2602 (OSC) so that the EVM-AC is maximized. 6. Set AM-SG to 600Hz. 7. Receive 600Hz in the unit. 8. Adjust Z2602 (ANT) so that the EVM-SG is maximized. Fig.7 13.3. Alignment Points 13.3.1.
SA-AK330GC / SA-AK330GN 14 Block Diagram OPTICAL PICKUP SEMICONDUCTOR LASER LPD Q7601 LD LASER POWER DRIVE B B PHOTO DETECTOR A A C B B B D B F F B E E B IC7003 AN8739SBTE2 FOCUS COIL/TRACKING COIL/ TRAVERSE MOTOR/ SPINDLE MOTOR DRIVE /RST 1 RESET SIGNAL GENERATOR FOCUS COIL F- 17 D4+ F+ 16 D4- 18 15 D3+ T+ 14 D3- TRACKING COIL M7301 M IN4 23 FOP TRACKING COIL DRIVE IN3 24 TRP IN1 6 TRVP NC T- TRAVERSE MOTOR FOCUS COIL DRIVE 11 D1+ 10 D1- TRAVERSE MOTOR DRIV
SA-AK330GC / SA-AK330GN TO MAIN BLOCK BLKCK MDATA MLD MCLK STAT A B X7201 CD_RST MICRO COMPUTER INTERFACE TIMING GENERATOR 47 48 43 49 AVSS2 AVDD2 45 PLLF MDATA 46 PLLF0 MCLK 44 IREF 64 DSLF 63 ARFIN 65 MLD STAT NRST 66 (PMCK) IOMODE 68 70 X2 59 71 X1 NTEST (SMCK) B 60 B TXTCK DSL/PLL/VCO TXTD DQSY B B A, B, C, D, E, F 27 30~35 B LD 37 LPD B A,B,C,D,E,F 29 LD 28 PD 36 DCDET 41 CAGC ARF 39 EFM DEMODULATION SYNC INTERPOLATION CIRC ECC CDROM ECC
SA-AK330GC / SA-AK330GN AM ANT FM ANT Z2620 Q1 (RF AMP) 1 CF2601 Q2601 Q2 7 MIXER Q3 5 CF2602 FM IF AMP Q4 6 D2602 L2601 BUFFER OSC L2602 B 8 B (FM) RCH 22 23 24 ALC 21 AM OSC BUFFER 19 20 18 17 16 PILOT CANCEL STEREO SWITCH AM DET AM IF AM/FM IF BUFFER FM DET 13 PHASE DET S-CURVE FM IF 14 DECODER AM RM AMP AM MIX AGC LEVEL DET 15 COMP VCO TUNING DRIVE FF REG 5 4 ST 3 FF PILOT DET REG SD 2 1 FF 6 7 8 9 10 11 12 B IC2601 LA1833NMNTLM X2602 Z
SA-AK330GC / SA-AK330GN FL6602 11~14, 16~29 1,2, 30~40 FL0 10 XOUT 3 FL DRIVER XIN ~CS 8 SDATA ~RESET FL13 SCK 9 FL12 5~19 FL30 23~40 IC6601 C0HBB0000044 FROM POWER TRANSFORMER G13 G1 P1 P18 FL DISPLAY 5 6 IC1 C0GAM0000005 MOTOR DRIVE 5 IN1 6 IN2 REG VS 8 OUT1 2 OUT2 10 B VREF VCC GND M 4 7 1 RM1 Q1 B PLLDA D2 POWER SUPPLY CONTROL B Q2907 STAT SWITCH SW2 PUSH SW1 PUSH SW3 OPEN Q2936 ST/DO CD MOTOR SUPPLY SWITCH B PLLCLK Q2906 BLKCK B Q2937
SA-AK330GC / SA-AK330GN IC1001 AN7348S-E1 P.B EQ/REC AMP/ ALC/TPS AMP LCH 24(23) (DECK 1) P.B.
SA-AK330GC / SA-AK330GN 7(8) IC2804 C0AABA000009 B1(2) DUAL OP-AMP OUT1(2) Q2181 (Q2281) 2(6) 22(21) 1(7) 3(5) HPF FREQ AMP SWITCH FILTER Q2142 (Q2242) 5(6) AGC CONTROL IC2806 C0ABBB000244 A1(2) DUAL OP-AMP 2(4) 32(31) SEL1(2) REC1(2) IC2803 C1BB00000732 FILTER 5 7 6 AUDIO SOUND PROCESSOR 3 1 2 HP_L(R) 13(14) JK2801 AUX IC2805 C0ABBB000244 E1(2) DUAL OP-AMP 3 1 2 C1(2) SI CD SIGNAL 18 SC 9(10) 5 7 6 17 FILTER Q2511, Q2512 Q2571 MUTING SWITCH SWITCH B Q27
SA-AK330GC / SA-AK330GN 16(15) -IN2 1(2) OUT 2 1(2) LCH 3(6) HIGH CH (6 W) IC5801 RSN315H42C-P JK5951 (JK5952) POWER HIC 13(12) OUT 1 1(2) -IN1 1(2) +VCC 1(2) +VD -VCC 1(2) 14 IN GND 11 OUT GND -VD AC DET -VCCM LCH 7(9) LOW CH (6 W) 4(2) 17 5(1) 18 8 D5814 10 B FILTER FILTER DC_DET Q5812, Q5813 Q5802, Q5805 DC DETECT SWITCH VOLTAGE SUPPLY/ CURRENT CONTROL SWITCH JK6551 HEADPHONE FAN HP _SW RCH Q5814 HEADPHONE MUTING SWITCH MUTE_H D5813 FAN Q5952 SYNC SYNCHRONISING SWI
SA-AK330GC / SA-AK330GN 15 Voltage Measurement 55
SA-AK330GC / SA-AK330GN 56
SA-AK330GC / SA-AK330GN 16 Schematic Diagram (All schematic diagrams may be modified at any time with the development of the new technology) Note: SW1 SW2 SW3 SW4 SW5 S951 S952 S971 S972 S975 S6101 S6102 S6103 S6104 S6105 S6106 S6201 S6202 S6203 S6204 S6205 S6206 S6207 S6208 S6209 S6210 S6301 S6303 S6304 S6305 S7201 VR6491 : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Push switch Push switch Open switch CD switch Load switch Mode switch Half switch Mode switch Half switch Recinh_F switc
SA-AK330GC / SA-AK330GN 16.1. (A) CD Servo Circuit SCHEMATIC DIAGRAM - 1 : +B SIGNAL LINE OPTICAL PICKUP CIRCUIT CD SERVO CIRCUIT 1 2 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 A GND B C7614 6.3V100 VREF LPD C7613 0.1 GND TT+ FF+ CN7001 R7329 1.5K R7328 18K R7349 15K R7327 1.5K C7335 0.
SA-AK330GC / SA-AK330GN SCHEMATIC DIAGRAM - 2 : +B SIGNAL LINE : CD SIGNAL LINE : CD-DA SIGNAL LINE CD SERVO CIRCUIT 20 C7625 6.3V220 C7626 0.1 26 C7223 6.3V100 C7224 0.1 21 R7217 1K 23 C7225 1000P C7226 1000P 0.015 0.1 1000P 0.082 C7244 C7217 C7241 C7218 R7211 82K R7218 1K C7263 0.1 R7212 820 22 R7221 100 C7231 6.3V220 C7230 0.1 C7234 16V10 C7233 0.1 C7232 6.3V220 LCH OUT C7216 680P C7253 C7264 0.1 C7105 0.1 C7235 16V10 +3.3V 13 D.GND 12 LD SW 11 470P TX 10 9 C7243 +7.
SA-AK330GC / SA-AK330GN 16.2. (B) Main (Tuner) Circuit SCHEMATIC DIAGRAM - 3 : +B SIGNAL LINE : FM SIGNAL LINE : AM SIGNAL LINE : FM/AM SIGNAL LINE : FM OSC SIGNAL LINE : AM OSC SIGNAL LINE MAIN (TUNER) CIRCUIT R2604 1K TUNER PACK CIRCUIT 5.6P 1000P C2604 1000P 18P 3.3P 390 2 R2607 330 CF2602 J0B1075A0061 3 1 R2601 0 R2606 470K 2 R2605 470 Q2601 Q2601 1000P 180P Q2606 B1AABC000003 FM IF AMP 4 6 390 220 100K 390 560K 5 C2601 0.01 2SC1675l1l2 4.7P 2.7K 5.
SA-AK330GC / SA-AK330GN 16.3.
SA-AK330GC / SA-AK330GN SCHEMATIC DIAGRAM - 5 5 4 3 2 1 C2753 0.1 C2751 0.1 R2266 33 R2268 33 R2267 33 R2269 33 R2167 33 R2169 33 R2171 3.3K R2247 100K R2149 2.2K C2151 16V10 R2246 1K C2245 16V10 R2146 1K IC2805 6 R2242 1.5K 2 3 C2522 1 R2511 100K 7 8 R2512 0 5 7 8 R2502 56K R2501 2.2K SYNC SYS6V C2141 1 R2532 0 MUTE_A 12K R2520 10K R2404 82K 5 6 R2503 27K C2501 50V2.2 7 8 6 C2527 C2526 220P CONN CONN3 1 R2538 10K R2521 10K R2519 4.
SA-AK330GC / SA-AK330GN SCHEMATIC DIAGRAM - 6 : -B SIGNAL LINE : +B SIGNAL LINE TO FAN UNIT MAIN CIRCUIT R2591 330K R2439 1K R2339 1K R2592 0 C2331 1 R2338 1K D2332 B0ADCC000002 R2333 0 C2332 0 R2337 470K CN2810 1 DCDET LM_L +9V VIN2 VIN1 2 C2334 0.
SA-AK330GC / SA-AK330GN SCHEMATIC DIAGRAM - 7 /HALF_1 1K 10K 10K R2843 R2842 R2841 /MODE_1 /PLG1 /REC /MTR /PLG2 10K R2844 VCC DECK1_H 4.
SA-AK330GC / SA-AK330GN SCHEMATIC DIAGRAM - 8 : +B SIGNAL LINE : AUX SIGNAL LINE : MAIN SIGNAL LINE : -B SIGNAL LINE : CD SIGNAL LINE : PLAYBACK SIGNAL LINE : FM/AM SIGNAL LINE : RECORD SIGNAL LINE MAIN CIRCUIT D2951 B0BC7R500001 +15V R2211 10K R2112 22K C2120 1 R2212 22K C2112 C2111 1000P 0.1 REC_L R2318 2.7K R2418 2.7K TO MAIN (TUNER) CIRCUIT (1A) ON SCHEMATIC DIAGRAM-3 +15V R2953 10K DO/ST R2317 100K R2111 10K C2951 0.01 TGND D2951 PBR PBL C2952 0.01 SD +9V DO/ST SD +7.
SA-AK330GC / SA-AK330GN 16.4. (C) Panel Circuit SCHEMATIC DIAGRAM - 9 : MAIN SIGNAL LINE : +B SIGNAL LINE : -B SIGNAL LINE PANEL CIRCUIT SYS6V S6210 POWER 6.8K R6209 R6208 4.7K 2.7K 1K 1K 1.2K R6207 R6102 R6103 R6104 JOG VOL S6207 SSEQ_LED LED9V R6491 47K R6492 47K VJOG_B Q6457 47K R6111 2.2K S6303 1.8K SSEQ R6303 1K S6202 TUNER R6302 1K S6201 REW VJOG_A R6493 10K LED DRIVE K2 KEY3 4 R6425 10K 5 HEADPHONE REC R6304 1.
SA-AK330GC / SA-AK330GN SCHEMATIC DIAGRAM - 10 : +B SIGNAL LINE : -B SIGNAL LINE : MAIN SIGNAL LINE PANEL CIRCUIT P18 FL2 FL2 P16 P15 P14 P13 P12 P11 P9 P8 P7 P17 FL30 FL11 FL29 FL28 FL27 FL09 FL10 FL26 FL08 FL25 FL07 FL24 FL06 FL23 FL05 FL22 FL04 FL21 FL03 P6 P5 P4 P3 P1 NC P2 FL02 FL20 FL19 FL18 FL17 FL16 FL15 FL01 FL14 NC FL00 FL13 NC NC NC FL12 G9 G8 G7 G6 G5 P10 G11 G10 G12 G13 FL11 FL10 FL09 FL12 FL08 FL07 FL06 FL05 G4 44 FL04 G3
SA-AK330GC / SA-AK330GN 16.5. (D) Transformer Circuit, (E) CD Detect Circuit, (F) Spindle Position Circuit & (G) CD Loading Circuit SCHEMATIC DIAGRAM - 11 : +B SIGNAL LINE : -B SIGNAL LINE TRANSFORMER CIRCUIT 1 D5950-D5953 B0EAMM000038 VCC+ 2 TO POWER CIRCUIT (H5950/ W5950) ON SCHEMATIC DIAGRAM-12 3 D5950 D5952 VCC- C5960 0.1 4 5 AC GND D5953 6 7 D5951 R5965 12K AC_IN T5950 ETP76VST62HB 8 SUB B 9 SUB+B GND D5956 D5954 C5959 C5950 25V2200 CN5950 FP5950 4000 RL5950 K6B1AEA00015 0.
SA-AK330GC / SA-AK330GN 16.6. (H) Power Circuit SCHEMATIC DIAGRAM - 12 : -B SIGNAL LINE : +B SIGNAL LINE : MAIN SIGNAL LINE POWER CIRCUIT IC5801 -VD +VD -IN 2 1 -IN 2 2 IN GND -IN 1 1 -IN 1 2 OUT GND -VCCM OUT 1 2 AC DET OUT 1 1 OUT 2 2 -VCC 1 +VCC 1 OUT 2 1 +VCC 2 -VCC 2 IC5801 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R5853 220K R5250 68K C5442 2200P C5443 39P C5240 2200P R5451 56K R5450 68K R5251 150K C5241 39P C5440 2200P C5445 0.
SA-AK330GC / SA-AK330GN 16.7. (I) Deck Circuit & (J) Deck Mechanism Circuit SCHEMATIC DIAGRAM -13 : +B SIGNAL LINE : PLAYBACK SIGNAL LINE : RECORD SIGNAL LINE DECK CIRCUIT C1038 220P AN7348S-E1 4 3 11 C1023 1000P C1021 470P C1043 50V4.7 C1056 16V10 C1036 0.033 HI/LO CRO/NOR AB SW RIPPLE FILTER OUTPUT GND VCC ALC T REC OUT REC/PB SW 13 REC IN 14 6 7 8 9 10 11 12 R1022 10K C1045 10V22 R1099 0 C1039 220P C1033 0.018 R1016 C1037 47 50V3.
SA-AK330GC / SA-AK330GN SCHEMATIC DIAGRAM - 14 : PLAYBACK SIGNAL LINE : +B SIGNAL LINE TO MAIN CIRCUIT (CN2803) ON SCHEMATIC DIAGRAM-4 6 5 4 3 2 1 CN1001 BP1 MOTOR 8 7 MO GND +B AFGND RECINL RECINR PBL PBR 14 13 12 11 10 9 DMT DECK1_H DECK CIRCUIT REC_H MO+B : RECORD SIGNAL LINE C1064 0 R1098 10K R1060 390 R1057 2.2K R1097 10K R1091 0 R1092 0 1 2 2 W1002 R1049 0 R1084 2.2K 1 + - M Q1017 B1AARC000002 C1049 3300P MOTOR SWITCH R1086 2.
SA-AK330GC / SA-AK330GN 17 Printed Circuit Board Note: Circuit board diagrams may be modified at any time with the development of new technology. 17.1. (A) CD Servo P.C.B.
SA-AK330GC / SA-AK330GN 17.2. (B) Main P.C.B. A D E F G MAIN P.C.B (REPX0442B...GC) (REPX0442C...
SA-AK330GC / SA-AK330GN H R2908 R2907 R2901 R2909 C2903 B W2265 C2907 2 3 W2902 W2901 W2280 W2281 R2927 W2283 C2905 C2816 W2270 C2999 R2862 1 R2861 2 3 4 5 6 7 8 80 81 W2269 W2504 W2271 W2209 R2916 W2282 W2266 W2508 C2817 R2921 E R2912 R2914 C2811 1 W2267 C2906 R2924 4 5 W2208 W2273 W2287 B R2856 C2812 6 7 C R2922 R2867 C2857 8 9 W2268 W2276 B W2904 R2929 Q2907 W2279 C2852 11 E C R2923 W2906 W2277 10 13 W2905 Q2906 2255 C2853 D2901 12 W
SA-AK330GC / SA-AK330GN 17.3. (C) Panel P.C.B.
SA-AK330GC / SA-AK330GN G 15 H 20 25 I 30 35 J 40 K L 44 CN6601 FL6602 1 3 5 2 30 31 4 7 6 9 8 11 13 15 17 19 21 23 25 10 12 14 16 18 27 29 20 22 24 26 W6105 R6458 28 30 J6902 W6101 W6100 M D6458 W6089 C6636 21 40 C6601 R6602 R6601 W6075 1 W6063 W6062 IC6601 W6102 20 W6083 W6076 W6082 W6085 S6301 W6065 R6611 W6033 11 W6087 10 POWER W6094 W6103 W6080 C6632 W6059 W6081 R6399 W6060 W6022 W6092 W6093 W6066 R6199 W6077 W6071 J6108 R6303 W
SA-AK330GC / SA-AK330GN 17.4. (D) Transformer P.C.B. A 1 B D C D E F G TRANSFORMER P.C.B (REPX0467B) CAUTION RISK OF ELECTRIC SHOCK AC VOLTAGE LINE. PLEASE DO NOT TOUCH THIS P.C.B 2 F1 250V 1.
SA-AK330GC / SA-AK330GN 17.5. (E) CD Detect P.C.B., (F) Spindle Position P.C.B., (G) CD Loading P.C.B. & (K) Tuner Pack P.C.B. A 1 B C D E F G G CD LOADING P.C.B (REP2578A-N) IC1 2 4 7 6 5 9 8 10 E OPEN J1 C B 8 10 4 6 2 1 13 11 9 7 5 3 2 3 4 1 CN1 Q1 SW1 J4 SW2 J2 C2 12 3 D2 SW3 J3 14 2 1 R1 3 C1 2 W1 W2 1 PUSH PUSH 3 M - 4 PbF 5 E F CD DETECT P.C.B (REP2578A-N) 6 D1 1 2 3 SPINDLE POSITION P.C.
SA-AK330GC / SA-AK330GN 17.6. (H) Power P.C.B. A 1 B H C D E F G POWER P.C.B (REPX0469G...GC) (REPX0469J...GN) 2 H5950/W5950 8 9 7 6 5 4 3 2 1 3 R5801 W5807 B C R5804 B W5805 W5831 W5832 C5840 W5866 W5876 W5867 W5872 C W5853 E W5841 Q5809...
SA-AK330GC / SA-AK330GN G H I J K L M 15 14 13 12 11 10 9 8 7 6 5 4 3 R5801 2 R5252 C5803 C5802 R5451 R5806 C5445 R5251 W5855 R5249 C5241 W5844 C5440 W5821 W5822 W5833 W5862 Q5813Q5812 B W5847 R5456 4 -R C5245 W5550 C E E R5256 2 -R R5255 LOW CHANNEL W5817 C5444 3 +L 4 +R J JK5952 R5854 R5856 1 2 3 4 5 6 7 8 9 10 11 J W5851 C5244 R5853 R5246 D5814 W5803 C5838 R5446 W5861 W5878 1 -L B C W5820 R5245 R5445 C5820 W5868 HIGH CHAN
SA-AK330GC / SA-AK330GN 17.7. (I) Deck P.C.B. & (J) Deck Mechanism P.C.B.
SA-AK330GC / SA-AK330GN 18 Wiring Connection Diagram FM ANT AUX AM ANT PbF CN2809 SOLDER SIDE To Fan CN2810 .......... 12 SOLDER SIDE CN2805 TUNER PACK (REP1999B) ...... ...... 1 2 E CD DETECT P.C.B 13 14 SOLDER SIDE 123 1. 3 1314 1 1 B MAIN P.C.B 1 W2 CN5801 12 ........ K TUNER PACK P.C.B 12 PbF PbF W2 ...... ...... H POWER P.C.B SOLDER SIDE 12 CN1 1 .. CN2808 4 CN2801 12 W1 1. . 4 16 15 F SPINDLE POSITION P.C.B ........... ........... PbF ..........
SA-AK330GC / SA-AK330GN 19 Illustration of IC’s, Transistors and Diodes C2CBJG000564 (100P) C0HBB0000044 (48P) MN6627953HB (80P) AN7348S-E1 (24P) LA1833NMNTLM (24P) LC72131MDTRM (20P) C1BB00000732 (32P) 5 8 1 1 1 4 5 1 1 AN8739SBTE2 CNB13030R2AU 1 C0GAM0000005 B1AAAC000011 B1AAAD000013 B1ACCF000063 B1GACFJJ0016 B1GACFLL0007 26 4 3 21 20 3 1 1 1 14 6 7 18 C0ABBB000244 2 2 RSN315H42C-P C0AABA000009 C1AA00000612 10 B C E 13 4 B1AAGC000007 B1GACFGG0004 B1ACKD000004 B1AARC000002
SA-AK330GC / SA-AK330GN 20 Terminal Function of IC’s 20.1. IC7002 (MN6627953HB) Servo processor/ Digital signal processor/ Digital filter/ D/A converter 1 2 3 4 Pin No.
SA-AK330GC / SA-AK330GN Pin No. 13 Mark D2+ O I/O 14 D3- O 15 D3+ O 16 D4- O 17 D4+ O 18 19 20 21 22 23 24 25 26 N.C. PGND2 PVCC2 VCC VREF IN4 IN3 RSTIN N.C. I I I - Function Motor driver (2) forward-action output Motor driver (3) reverse-action output Crystal oscillating circuit input (f = 16.
SA-AK330GC / SA-AK330GN Pin No. 97 Mark PHOTO_1 98 99 100 VREF AVcc Demo I/O Function I Rotation Detection Signal (Deck 1) Reference for A-D (5V) Analog Power Supply Input I (H= default demo on, L= default demo off.
SA-AK330GC / SA-AK330GN 21 Troubleshooting Guide 87
SA-AK330GC / SA-AK330GN 22 Parts Location and Replacement Parts List Notes: · Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality sound (capacitors), low noise (resistors), etc are used. When replacing any of these components, be sure to use only manufacturer’s specified parts shown in the parts list.
SA-AK330GC / SA-AK330GN 22.1. Deck Mechanism (RAA4502-S) 22.1.1.
SA-AK330GC / SA-AK330GN 90
SA-AK330GC / SA-AK330GN 22.1.2. Deck Mechanism Parts List Ref. No. 101 102 103 104 105 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 128 129 130 130-1 132 133 133-1 133-2 134 135 136 137 138 139 Part No.
SA-AK330GC / SA-AK330GN 22.2. CD Loading Mechanism (RD-DAC026-S) 22.2.1.
SA-AK330GC / SA-AK330GN 93
SA-AK330GC / SA-AK330GN 22.2.2. CD Loading Mechanism Parts List Ref. No. 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 341 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 358-1 358-2 358-3 358-4 358-5 358-6 358-7 358-8 358-9 358-10 359 360 361 362 Part No.
SA-AK330GC / SA-AK330GN 22.3. Cabinet 22.3.1.
SA-AK330GC / SA-AK330GN 96
SA-AK330GC / SA-AK330GN 22.3.2. Cabinet Parts List Ref. No. 1 2 3 4 5 6 7 7-1 9 9 10 11 12 13 14 16 17 Part No.
SA-AK330GC / SA-AK330GN Ref. No. Q5953 Q6411 Q6415 Q6421 Q6425 Q6457 Q7601 Part No. B1AACF000064 B1ACKD000004 B1ACKD000004 B1GACFLL0007 B1GACFLL0007 B1GACFLL0007 B1ADCF000001 Part Name & Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Remarks [M] [M] [M] [M] [M] [M] [M] Ref. No.
SA-AK330GC / SA-AK330GN Ref. No. Part No. L2996 ERJ3GEY0R00V Part Name & Description CHIP JUMPER Remarks [M] T5950 T5951 POWER TRANSFORMER BACK UP TRANSFORMER [M] [M] ETP76VST62HB RTP1H3E002 Ref. No.
SA-AK330GC / SA-AK330GN Ref. No. R5 R6 R7 R8 R9 R10 R11 R952 R953 R972 R973 R1001 R1002 R1003 R1004 R1005 R1007 R1009 R1010 R1011 R1012 R1013 R1014 R1015 R1016 R1017 R1018 R1019 R1020 R1022 R1024 R1025 R1026 R1027 R1028 R1029 R1030 R1031 R1032 R1035 R1040 R1049 R1050 R1055 R1057 R1060 R1084 R1085 R1086 R1087 R1090 R1091 R1092 R1097 R1098 R1099 R1100 R1101 R2101 R2102 R2103 R2106 R2107 R2108 R2111 R2112 R2113 R2116 R2117 R2118 R2141 R2142 R2143 R2146 Part No.
SA-AK330GC / SA-AK330GN Ref. No. R2511 R2512 R2513 R2514 R2515 R2516 R2517 R2518 R2519 R2520 R2521 R2522 R2523 R2524 R2525 R2527 R2531 R2532 R2533 R2534 R2535 R2537 R2538 R2539 R2571 R2582 R2584 R2585 R2586 R2587 R2591 R2592 R2601 R2602 R2603 R2604 R2605 R2606 R2607 R2610 R2611 R2612 R2613 R2614 R2615 R2616 R2617 R2618 R2619 R2620 R2621 R2622 R2623 R2624 R2625 R2626 R2627 R2628 R2629 R2630 R2631 R2632 R2633 R2634 R2635 R2636 R2637 R2638 R2641 R2642 R2643 R2644 R2645 R2646 Part No.
SA-AK330GC / SA-AK330GN Ref. No. R2916 R2917 R2918 R2919 R2920 R2921 R2922 R2923 R2924 R2925 R2926 R2927 R2928 R2929 R2930 R2931 R2932 R2933 R2936 R2937 R2938 R2939 R2940 R2941 R2942 R2943 R2944 R2945 R2946 R2952 R2953 R2954 R2976 R2977 R5245 R5246 R5247 R5248 R5249 R5250 R5251 R5252 R5255 R5256 R5445 R5446 R5447 R5448 R5449 R5450 R5451 R5452 R5455 R5456 R5801 R5802 R5804 R5805 R5806 R5807 R5808 R5809 R5810 R5811 R5812 R5813 R5814 R5815 R5816 R5817 R5818 R5818 R5819 R5819 Part No.
SA-AK330GC / SA-AK330GN Ref. No. R6601 R6602 R6603 R6604 R6611 R6631 R6632 R6641 R6642 R6643 R6644 R7102 R7104 R7105 R7106 R7144 R7211 R7212 R7214 R7217 R7218 R7220 R7221 R7253 R7254 R7315 R7323 R7325 R7327 R7328 R7329 R7331 R7335 R7336 R7339 R7349 R7601 R7650 Part No.
SA-AK330GC / SA-AK330GN Ref. No. C2251 C2266 C2281 C2282 C2283 C2284 C2291 C2292 C2293 C2301 C2302 C2311 C2312 C2331 C2332 C2334 C2401 C2402 C2411 C2412 C2501 C2511 C2512 C2513 C2520 C2521 C2522 C2523 C2525 C2526 C2527 C2581 C2582 C2583 C2584 C2585 C2588 C2601 C2602 C2603 C2604 C2606 C2607 C2608 C2609 C2610 C2611 C2612 C2613 C2614 C2615 C2616 C2617 C2618 C2619 C2620 C2621 C2622 C2623 C2624 C2625 C2626 C2627 C2629 C2630 C2631 C2632 C2633 C2634 C2636 C2637 C2638 C2639 C2641 Part No.
SA-AK330GC / SA-AK330GN Ref. No. C5812 C5813 C5814 C5820 C5838 C5840 C5950 C5951 C5952 C5953 C5954 C5955 C5956 C5957 C5958 C5959 C5960 C5963 C5971 C6481 C6491 C6492 C6551 C6552 C6553 C6601 C6602 C6603 C6604 C6612 C6621 C6623 C6631 C6632 C6635 C6636 C7102 C7105 C7106 C7107 Part No.
SA-AK330GC / SA-AK330GN 22.6.
