Operation Manual

ManualsBrandsBH SENS ManualsAutomotiveTPMS SENSOR

Table Of Contents

OPERATION MANUAL OF TPMS SENSOR

MODEL: TMSS6A4

Thank you for choosing our TPMS. This guide instructs the technician how to properly

mount and dismount a Baolong Huf TPMS clamp-in sensor.

Introduction of TMSS6A4

TMSS6A4 is the transmitting module in TPMS. Its working frequency is 433.92MHz;

Receiver Low frequency ： 125KHz; Maximum Transmit Power: < 10 mW.

supply:Battery;Radio frequency uses the FSK modulation and Machester encoding

mode;Antenna type:Monopole antenna,antenna Gain:-25dBi;cable loss ： 3.12dB.The

communication mode between WARDKS and receiving module is RF wireless

communication. The module detects pressure and temperature inner the tire periodically

and sends these information via RF output circuit to the receiving module. One can

manually detect data inner tire by LF wake-up tools. Install it on the rim together with cycle

valve.

PART ONE MOUNTING AND DISMOUNTING OF TRANSMITTER

1. Mounting of Transmitter

1.1 Identify Transmitter

Check whether the prepared sensor is the same with the image below.

Note: Only plastic or aluminum caps, aluminum valves and nickel plated valve cores can be

used when replaced.

① Self-lock Screw

② Electronal Module

③

Valve Stem

⑤ Valve Cap

④ Nut

Summary of content (6 pages)

PAGE 1
OPERATION MANUAL OF TPMS SENSOR MODEL: TMSS6A4 Thank you for choosing our TPMS. This guide instructs the technician how to properly mount and dismount a Baolong Huf TPMS clamp-in sensor. Introduction of TMSS6A4 TMSS6A4 is the transmitting module in TPMS. Its working frequency is 433.92MHz; Receiver Low frequency ： 125KHz; Maximum Transmit Power: < 10 mW.
PAGE 2
1.2 Before the transmitter is installed, the rim around the hole must be cleaned with a cloth. 1.3 Take off the nut④, insert the valve stem through the rim hole from inside. 1.4 Place nut④ on the valve stem, and tighten with 5 Nm (44 inch pounds) torque. 1.5 Lock the rim on the tyre changer. (If the mounting head of the tyre changer is positioned at 12 o’clock, then the valve should be at the 7 o’clock position.) Apply lubricant on both the tyre bead and rim. Mount the lower tyre bead on the rim.
PAGE 3
1.7 Apply soapsuds on the valve tip. If no leakage is found, put on the valve cap○6 . If unsuccessful, try again. 1.8 Dynamically balance the wheel before it is placed back on the vehicle. 2. Dismounting of Transmitter 2.1 Deflate the tyre and remove the wheel weights from the rim. Push the tyre bead away from the rim. Make sure to always set the bead breaker at least 90 degrees from the valve stem to avoid damaging the electronic module. 2.2 Firmly fix the wheel on the turntable clamps.
PAGE 4
PART TWO FCC’s Authentication Announcements Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 5
prepaid. The owner is responsible for any labor and installation charges. The warranty does not include any further obligation whatsoever, including but not limited to actual installation of the replacement unit on the customer’s vehicle. All other Warranties, expressed or implied, are disclaimed. All collateral agreements, which purport to modify this limited warranty, are of no effect. The absolute limit of liability is the purchase price of the unit.
PAGE 6
Gewerbestraße 40 D-75015 Bretten *** Hereby, Baolong Huf Shanghai Electronics Co., Ltd. declares that the radio equipment type TMSS6A4 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.intellisens.com/downloads Frequency band: 433.92 MHz Maximum Transmit Power: < 10 mW Manufacturer: Baolong Huf Shanghai Electronics Co., Ltd.