Operation Manual

ManualsBrandsBH SENS ManualsAutomotiveTPMS SENSOR

OPERATION MANUAL OF TPMS SENSOR

MODEL: TMSS5B5

Thank you for choosing our TPMS. This guide instructs the technician how to properly

mount and dismount a Baolong Huf TPMS clamp-in sensor.

Introduction of TMSS5B5

TMSS5B5 is the transmitting module in TPMS. Its working frequency is 2.4GHz;

Establish information communication via Bluetooth； 4dBm≥EIRP. supply: Battery. The

communication mode between WARDKS and receiving module is RF wireless

communication. The module detects pressure and temperature inner the tire periodically

and sends these information via RF output circuit to the receiving module. One can

manually detect data inner tire by LF wake-up tools. Install it on the rim together with cycle

valve.

PART ONE MOUNTING AND DISMOUNTING OF TRANSMITTER

1. Mounting of Transmitter

1.1 Identify Transmitter

Check whether the prepared sensor is the same with the image below.

Note: Only plastic or aluminum caps, aluminum valves and nickel plated valve cores can be

used when replaced.

① Self-lock Screw

② Electronal Module

③ Valve Stem

⑤ Valve Cap

Valve Stem

④ Nut

Valve

Stem

Summary of content (6 pages)

PAGE 1
OPERATION MANUAL OF TPMS SENSOR MODEL: TMSS5B5 Thank you for choosing our TPMS. This guide instructs the technician how to properly mount and dismount a Baolong Huf TPMS clamp-in sensor. Introduction of TMSS5B5 TMSS5B5 is the transmitting module in TPMS. Its working frequency is 2.4GHz; Establish information communication via Bluetooth； 4dBm≥EIRP. supply: Battery. The communication mode between WARDKS and receiving module is RF wireless communication.
PAGE 2
1.2 Before the transmitter is installed, the rim around the hole must be cleaned with a cloth. 1.3 Take off the nut④, insert the valve stem through the rim hole from inside. 1.4 Place nut④ on the valve stem, and tighten with 5 Nm (44 inch pounds) torque. 1.5 Lock the rim on the tyre changer. (If the mounting head of the tyre changer is positioned at 12 o’clock, then the valve should be at the 7 o’clock position.) Apply lubricant on both the tyre bead and rim. Mount the lower tyre bead on the rim.
PAGE 3
1.7 Apply soapsuds on the valve tip. If no leakage is 6 . If unsuccessful, try again. found, put on the valve cap○ 1.8 Dynamically balance the wheel before it is placed back on the vehicle. 2. Dismounting of Transmitter 2.1 Deflate the tyre and remove the wheel weights from the rim. Push the tyre bead away from the rim. Make sure to always set the bead breaker at least 90 degrees from the valve stem to avoid damaging the electronic module. 2.2 Firmly fix the wheel on the turntable clamps.
PAGE 4
PART TWO FCC’s Authentication Announcements Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 5
The warranty will be honored by any authorized Baolong Huf dealer. The owner is required to provide date of proof of purchase. The authorized dealer will determine if there is a warranty condition associated with materials and/or manufacturing workmanship. If a warranty condition exists, the component will be replaced free of charge and shipping prepaid. The owner is responsible for any labor and installation charges.
PAGE 6
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ce matériel est conforme aux limites de dose d'exposition aux rayonnements, CNR-102 énoncée dans un autre environnement.