Welcome Message Welcome Message Thank you for choosing a DP-S1, the epicenter of your home network. The DP-S1 supports not only the features of the conventional digital broadcasting receiver (STB, Set-top Box) and PVR (Personal Video Recorder), but also all the ways of watching the multimedia content with your PC and Internet; the USB (Universal Serial Bus) ports and the networking feature combining with DivX playback, you can play any multimedia content in any storage device with no external device.
Precaution Precaution Read this manual carefully before using this product. The cautions z Do not repair, disassemble or modify this apparatus yourself. It can described below contain important information about safety, and are cause fire or electric shock. If internal checking or maintenance is categorized into: Danger, Warning and Notice. The company will not be needed, please contact your service center or agency.
Precaution NOTICE WARNING If the product is mishandled, the user might receiver a serious If the product is mishandled, it might cause minor damage. or minor injury. Damage or loss to the user’s property may also occur. z If the apparatus becomes marked, clean it gently with a soft cloth or towel. Never use chemical solvents such as benzene, thinner, acetone z The product must not be exposed to water or liquid. If the apparatus or other solvents.
Precaution About the internal hard disk drive The internal hard disk drive (HDD) is a fragile piece of equipment. Please use the apparatus within the guidelines below to protect against possible HDD failure or to protect against accidental loss. This symbol is intended to alert the user to the presence of z Do not move the apparatus while it is on. uninsulated “dangerous voltage” within the product’s enclosure z Install and use the apparatus on a stable, level surface.
Precaution Copyright This manual is protected by copyright laws. Copy, use, reproduction of this manual in part or whole without beyonwiz's prior written permission is prohibited. Disclaimer The manufacturers, distributors and agents are not liable to any kind of damage caused by the use of the information contained in this manual. The instruction and descriptions which this manual contains are based on the time of this manual's production.
Contents Contents Welcome Message Precaution 1. Package Contents 2. Introduction ii 1 2 1. DP-S1 Highlights and Features 2 2. Front Panel 2 3. Rear Panel 2 4. Remote Control 3 5. Front Display 4 3. How to Connect 5 1. A/V Connection 5 2. Antenna Connection 6 3. LAN and W-LAN Connection 7 4. Quick Setup 1. Start Quick Setup vi i 11 5. STB & PVR Function 27 1. Basic STB Function 27 2. Service Edit 33 3. PVR Function 36 4. EPG 48 6. File Playback Function 51 1.
Package Contents 1. Package Contents The following elements are included in the gift box. Please check all package contents before using your product. z DP-S1 z Remote Control Batteries of z the Remote Control (AAA size x2) NOTICE: Two side panels are packaged separately. Please assemble the panels as illustrated on the carton box.
Introduction 2. Introduction 1. DP-S1 Highlights and Features 2. Front Panel Touch Buttons (x8) As a HD (High Definition) multimedia epicenter, the DP-S1 supports (Menu, Ch -, Ch +, Vol -, Vol +, OK, Stop/Eject, Standby) various ways of connecting to HD TVs and audio systems; HDMI port combining with HD video decoders, which support MPEG-2, MPEG-4, H.264 and WMV9, give you the true HD digital A/V environment.
Introduction 4. Remote Control The enclosed remote control can also be used to control a TV set provided by major TV manufacturers. The STB and TV buttons set the remote control to control the DP-S1 and TV set respectively. You can check the operating mode of remote control from the red backlight of the STB and TV buttons.
Introduction 5. Front Display The front display window gives you easy way to check the status of the DP-S1. 1 2 Indicates hard disk space used. Lights when there is no space left on the HDD. Lights when there is no time information. 3 Lights when a timer recording is programmed in standby mode. 4 Lights when the signal comes out via HDMI. 5 Lights when the signal is HD (High Definition). 6 Indicates the resolution of video output. 7 Lights when the video output is in Progressive Scan mode.
How to Connect 3. How to Connect 1. A/V Connection 1-1. Video Connection Depending on your A/V equipment including TV which you would like to To connect your DP-S1 to your TV or display, you have the following connect to, there are various ways you can connect the DP-S1 and A/V options; equipment. To make the best connections, please refer to the manual of Only one connection can be done at a time.
How to Connect 1-2. Audio Connection 2. Antenna Connection To connect your DP-S1 to your TV or audio system, you have the Please connect your TV Antenna to the DP-S1. following options; Only one connection can be done at a time. z S/PDIF Digital Audio output (COAXIAL, OPTICAL) z 5.
How to Connect 3. LAN and W-LAN Connection 3-1. Connection Using a Network Router In order to utilize the DP-S1 fully, it is strongly recommended to As shown in the picture, you have to connect the DP-S1 to the router connect the DP-S1 to the home network with a network router. with an Ethernet cable included in the box.
How to Connect 3-2. Connection Using a Wireless Router The DP-S1 supports 802.11g wireless LAN protocol, thus it is strongly As shown in the picture, you have to connect the DP-S1 to the router recommended to connect the DP-S1 to a wireless router compatible through wireless network. If you purchase a wireless router with a DP- with 802.11g protocol.
How to Connect 3-3. Direct Connection to the PC With this configuration, you can share contents with a PC through home If your PC has the DHCP server feature and it is enabled, all the network but the DP-S1 can not access to Internet. For this connection, configurations for networking will be set automatically and the DP-S1 is the following equipments are required; ready to communicate with your PC.
How to Connect 3-4. Direct Connection to Internet With this configuration, you can not share contents with a PC through NOTE home network. For this connection, a crossed Ethernet cable (not z The wireless LAN function of the DP-S1 requires more hardware included in the box) is required. The most ISP (Internet Service resources of the DP-S1. Therefore, the functionality can be limited if Provider) services DHCP feature. Therefore, you can connect your DP- you are using the wireless LAN.
Quick Setup 4. Quick Setup 1-1. Quick Setup of Video Output Format This chapter guides you to set up the DP-S1 quickly so that you can If the front display window indicates that the DP-S1 is ready to use but experience it’s basic features. In order to enjoy the DP-S1 fully, please nothing displays on the TV screen, you have to adjust the format and refer to Chapter 8. Advanced Setup. resolution of the video output by pressing the TV-OUT button. The default video output is in a SD PAL (576i) format.
Quick Setup 1-2. Basic Operation 1) Enter and Exit Setup Menu You can enter the SET-UP MENU with the SET-UP button on the remote control and exit to the previous operation mode such as LIVE or FILE PLAY with the EXIT button. 2) Setup Menu Structure The SET-UP menu is grouped in four parts: CONFIGURATION, NETWORK, MISCELLANEOUS and MANAGEMENT. Firstly, you have to choose one of these categories (main category) which are placed on the top menu (a horizontal bar) as graphical icons.
Quick Setup 3) How to Change Configuration In the setup menu, there are several ways to change the configuration. z Setup using the NUMERIC buttons: The NUMERIC buttons are used This manual explains how to change the configuration, here are three to set a configuration with numbers such as time information. You can cases which are used frequently. also move the cursor to left or right with the LEFT of RIGHT buttons while you are editing the configuration.
Quick Setup z On-screen keyboard: If you need to input alphabetic characters, an If you need to input numbers or special characters, please press the on-screen keyboard will be displayed. You can move the cursor with GREEN button. The screen keyboard turns to numbers and special the UP/DOWN/LEFT/RIGHT buttons and select the letters with the characters. You can also exit and return to small characters with the OK button. The YELLOW and BLUE buttons work as a space and GREEN button.
Quick Setup 2. Configuration 2-1. Time Setting Please set the current date and time. The date and time information will be the reference for the timer recording. Therefore, you have to z Mode: You can select how to set the date and time. Please press the OK button then you get a pop-up menu. You can choose one with the configure the time and date information precisely. You can also select UP/DOWN buttons and select it with the OK button. Under the preferred date and time formats.
Quick Setup z z Date Format: Please select a display format for the date either NOTE “DD/MM/YYYY”, “MM/DD/YYYY” or “YYYY/MM/DD” on a pop-up menu. z (DD-day, MM-month, YYYY-year) automatically from DTV station when you turn on the DP-S1 and Time Format: Please select how to display the time: either a 12-hour watch a program. But some DTV station doesn’t send the GMT format or a 24-hour format. You will get a pop-up menu if you press information or sends wrong information. the OK button.
Quick Setup 2-2. A/V Output Setting You have to set the video and audio configuration according to your TV 1) Video Outputs z set. Please make sure the video and audio port of the DP-S1 is connected to your TV set. support the PAL format in Australia. z TV Aspect Ratio: Please select either 4:3 or 16:9 according to your TV screen ratio. The A/V Output menu consists of two parts; the video output and the audio output.
Quick Setup - Pan&Scan: The picture is displayed in full on your 4:3 TV screen, but left and right sides of the original picture cannot be displayed. NOTE z The component video output supports SD (576i for PAL and 480i for NTSC), 480p, 576p, 720p and 1080i. z If you set the video output resolution as HD (more than 576p), the composite and S-Video outputs will be disabled automatically.
Quick Setup 2) Audio Outputs The DP-S1 supports 5.1ch audio in an analog format with the Dolby NOTE z Digital and DTS decoders. It also supports digital outputs with optical and coaxial ports. If you set the audio format as 2ch, the DP-S1 mixes down 5.1ch audio source to 2ch audio. z If the content of a channel broadcasted has 2ch audio source, the DPS1 can not expand the 2ch audio source to 5.1ch audio format.
Quick Setup 2-3. Service Scan Before watching a broadcasted program, you need to scan all the z Antenna DC (+5V) Power: You can supply DC (+5V, max. 100mA) services first. The scanned services will be stored in the non-volatilizing power to the indoor antenna through the antenna cable. Please make memory. Therefore you don’t have to scan the service again unless you sure that your external antenna is an active type, which means that delete all the information of the service stored in the memory.
Quick Setup z Start Scan: After selecting your scanning range, you can “start NOTE scanning”. Select Start Scanning and then press the OK button. On z You can not select an end channel smaller than the start channel. the screen, the scanning window appears and displays the process. z If you scan over all the channels with the “FULL” option, the previous service information including the service list information and your favorite lists will be erased automatically.
Quick Setup 3. Network 3-1. Setting The DP-S1 supports two networking interfaces: Ethernet and wireless The first step is to select an interface and configure it. You can select LAN. You can use one of these interfaces at a time. To use the wireless this in the Network Device menu. You will get a pop-up menu by LAN interface, you have to prepare a wireless router. This section will pressing the OK button. If you want to use the Ethernet interface, guide you how to configure the network interfaces.
Quick Setup 1) LAN Setting If you select the “LAN” option on the “Network Device” menu, all the items to be configured for the Ethernet interface will be displayed. z DHCP: If you want to get the all the configuration from the router and set automatically, please select the “Enable” option. In this case, the rest of the items are disabled to select because you don’t have to configure them manually. You can apply the change by pressing the RED button.
Quick Setup z IP Address: If you select the “Disable” option in the “DHCP”, you have z to input the IP address manually. You can input the address with the MAC Address: This will display the MAC address of the Ethernet interface but you can not change it. NUMERIC buttons and the LEFT/RIGHT buttons. You can move to the next item of Subnet Mask with the DOWN button. You can configure the following items in the same way; Subnet Mask, Gateway, NOTE Primary DNS Server IP and Secondary DNS Server IP.
Quick Setup 2) W-LAN Setting The other interface available for networking is the wireless LAN. You can z Network Type: you have to specify the type of the device which the set and use this interface by setting the “Network Device” menu as “W- DP-S1 communicates with. If you connect your DP-S1 with a router, LAN”. please set the “Network Type” as “Infrastructure”.
Quick Setup 3-2. Ice Guide The DP-S1 supports iceTV service through the Internet. If you have an z iceTV account, please set your account to utilize the service on your DPS1. Owner ID: if you press the OK button, on-screen keyboard will displayed and you can enter your ID of iceTV account. z Password: if you press the OK button, the on-screen keyboard will displayed and you can enter your password. z Check User Info: you can check if your account information is valid or not.
STB & PVR Function 5. STB & PVR Function The DP-S1 supports various ways of enjoying multimedia contents and it groups its features in three parts; the first group is STB (Set-top Box) and PVR (Personal Video Recorder) functions, the second group is file playback functions including playback of recorded programs with PVR 2) Change Service with Service List The service list contains all the broadcasting services you can receive.
STB & PVR Function You can also edit the service list in the list view. This will be explained in NOTE the later section. z If you change a service continuously with the CH+ or CH- button, only the information box will be changed according to your command: You can watch the changed service 3 seconds after you press the last NOTE z You can hide the help message and extend the service list with the button. z RED button.
STB & PVR Function 1-2. Information Box You can check the information of a service and the program using three information boxes; the information box contains specific information of a current service and program. The extended information box contains more details about the current program. And the recording information box shows the recording status. You can check these by pressing the INFO button and cancel it by pressing the EXIT button.
STB & PVR Function 1-3. Volume Level Adjust 1-4. Soundtrack Change With the VOL+/VOL- buttons, you can adjust the volume level of the If the current TV program provides more than one language or audio analog audio output. The MUTE button will turn off the analog and format, i.e. MPEG audio and Dolby audio, together, you can select one digital audio outputs. and change to that setting while you are watching a TV program.
STB & PVR Function 1-5. Subtitle and Teletext Service 1) Subtitle Service 2) Teletext Service If you want to view subtitles on the screen, please press the SUBTITLE The teletext is a free service broadcasted by TV stations which gives the button. To display the subtitle, please select “Enable” and press the OK latest information on news, weather, television programs, share prices button. You can hide the subtitle by selecting “Disable” with the OK and many other topics.
STB & PVR Function 1-6. Sleep Timer You can set the DP-S1 to turn off automatically at a specific time. Press the SLEEP button to set the timer. The DP-S1 will only turn off after a recording has finished even if you set it to turn off before the completion of the current recording(s). To cancel the timer, please press the SLEEP button successively until you set time as “0 min”.
STB & PVR Function 2. Service Edit 2-1. Service List Edit You can edit the service list if you want. The followings illustrate the editing functions you can use to edit a service list. z Delete: You can delete the marked service from the service list. Press the YELLOW button to delete. You have to re-scan if you want to watch the deleted service(s) again. 2-2. Favorite Group Favorite group is your personal collection of TV or radio services.
STB & PVR Function belong to the favorite group. Please select a favorite group in the left column with the UP/DOWN buttons and press the OK button. Then the cursor moves to the right column. On the right column, the services belong to the favorite group that was selected on the left column will be displayed. You can select a service with the UP/DOWN buttons. If you want to change to a certain service, please press the OK button on that highlighted service.
STB & PVR Function 4) Service Change on Favorite Group If you change services using the service list when you select a favorite group, the service list will show the services belong to that favorite group. You can change among these services on the list. If you want to exit from a favorite group and list up all services available in the service list, please press the BLUE button when the service list is displayed.
STB & PVR Function 3. PVR Functions The major functions of PVR are time-shifting and recording. If you want z to play a recorded program, please use the multimedia contents playback function with the FILE PLAY button on the remote control. STOP button will skip and jump to the live position when you watch the picture at time-shifted position. z PAUSE button will hold the picture until you select play again with the PLAY button. Chapter 6.
STB & PVR Function z LEFT button skips and moves backward 15 seconds at a time. You can also jump to a certain position with the LEFT button. The anchor NOTE z mark moves backward while you are holding down the LEFT button. watching a third service, the time-shift function for the third program You can play and watch from the anchored position by releasing the LEFT button. z will be disabled automatically. z RIGHT button skips and moves forward 15 seconds at a time.
STB & PVR Function 3-2. Instant Recording z 1) Start Recording Starting Point: You can select the starting point of recording with the LEFT/RIGHT buttons when the time-shift function is enabled. If the You can record the current service and store it in the HDD instantly by time-shift function is disabled, you can only record from the current pressing the REC button. The following picture shows options you can time. 1.
STB & PVR Function NOTE z If you disable the time-shifting function, you can’t record a program from the time-shifting buffer. Therefore you can only choose a single option of “1. Live” when you intend to record a program. z If there is only one program in the time-shift buffer. The two options of “2. Current Program” and “3. All” have the same meaning.
STB & PVR Function 3) Pause/Resume and Stop Recording 4) Change Recording Options while Recording If you want to skip recording for a certain period of time, i.e., You can change the duration of a recording or file name after the commercial advertisements, please press the REC button while you are recording has started. You can also lock or unlock the recording file watching the recording service. while you are recording the service.
STB & PVR Function Please select a recording item with the UP/DOWN buttons to change. If there is one recording, only one item will be displayed. z You can change the duration with the LEFT or RIGHT button. z You can change the file name with the RED button. An on-screen keyboard will be displayed to edit the file name. z You can change the locking status of the recording file with the GREEN button. NOTE z You can stop the recording with the STOP button.
STB & PVR Function 3-3. Timer You can set programs which you would like to record to HDD. The timer function can also be used to turn on the DP-S1 and watch the set program or transmit the picture to an external recording device such as a VCR (Video Cassette Recorder) according to your timer reservations. You can set up to a maximum 200 timers. 1) View Timer List You can view and check all of the timer information; modifying or delete a timer and add a new timer to the timer list.
STB & PVR Function 2) Add New Timer To add a timer, please press the RED button to display a menu on the z buttons and change date with the NUMERIC buttons. screen. A new pop-up window will appear to configure the timer. You can configure the following items with your preference for a new Date: Set start date of recording. Move cursor with the LEFT/RIGHT z Start Time: Set start time. Move cursor with the LEFT/RIGHT buttons and change time with the NUMERIC buttons. time record.
STB & PVR Function 3) Edit Timer 4) Delete Timer You can modify a timer setting such as service, start date, start time, Select a timer which you want to delete with the UP/DOWN buttons duration, recurrence and mode. Please choose a timer with the and press the GREEN button. A pop-up confirmation will appear and UP/DOWN buttons on the timer list and press the OK button to change. choose “Yes” with the OK button.
STB & PVR Function 5) Turn On and Off the DP-S1 according to Timer If a timer starts when the DP-S1 is in standby mode, the DP-S1 is turned on automatically and performs its operation according to the timer. Once the timer is ended, a pop-up message will appear to ask if you are operating the DP-S1 or not. If there is no confirmation to turn off, the DP-S1 will be turned off and go into standby mode. If you want to use the DP-S1 continuously, select “No” on the screen and press the OK button.
STB & PVR Function 3-4. Duplicated Recording The DP-S1 can record up to two programs simultaneously. If you intend to record more than two programs simultaneously, a pop-up warning of duplication will be displayed. 1) Duplication When New Recording Starts If a new recording starts because of an instant recording or a timer setting while the DP-S1 records two programs simultaneously, a warning message will pop up of the duplication. In these cases, the following pop-up will be displayed.
STB & PVR Function 2) Duplication When a New Timer Sets As explained before, the DP-S1 can record two programs simultaneously. Therefore you can not add a new timer to record three programs at the same time. If this occurs, a pop-up list is displayed to show the list of duplicated timers if a new timer is entered as a duplication. In order to add a new timer when duplication occurs, please delete one group of timers displayed in the duplication timer list.
STB & PVR Function 4. EPG (Electronic Program Guide) The EPG (Electronic Program Guide) is a time table of TV programs which show upcoming programs on a network. The EPG information is supplied by TV broadcasters as an optional service, therefore the DP-S1 can not provide a full EPG if some broadcasters do not provide this information. The DP-S1 supports a full 7-day EPG provided as a subscription from IceTV. Please visit the IceTV website, www.icetv.com.
STB & PVR Function 4-2. EPG with Multiple Services This EPG shows 4 services at a time. The vertical axis implies services The small screen displays the program you watched before you entered and the horizontal axis implies time. You can move the cursor and the EPG. The screen will not change when you change the service or explore the programs with the UP/DOWN/LEFT/RIGHT buttons; the program in order to prevent from refreshing the time-shifting buffer. UP/DOWN buttons change service.
STB & PVR Function 4-3. Service Change and Recording 1) Service Change 3) Resolving Duplication If you want to change and watch a certain program, place the cursor on If a new recording or timer setting produces a duplication to the current the program you want to watch and press the OK button. This action recordings or the timers previously set, a pop-up windows will be automatically exits from the EPG then you will watch the program on displayed, which is explained in the previous section.
File Playback Function 6. File Playback Function This chapter covers all functions regarding playing multimedia contents. The DP-S1 can play movie, music and photo files stored in the internal hard disk drive, PCs on the home network, optical disk such as DVD or CD, USB storage devices, and memory cards. You can also play the recording contents in this mode. You can enter this operation mode with the FILE PALY button. 1.
File Playback Function 1) Step 1: Select Content Type With the LEFT/RIGHT buttons, you can select a content type you want to play. If you select “Movie” icon on the top menu, only the movie files will be displayed on the screen even though a folder or device contains other type of contents such as music or photo. You can also choose “Music” or “Photo” icon with the LEFT/RIGHT buttons. 2) Step 2: Select Storage With the UP/DOWN buttons, you can select a device to access.
File Playback Function content type; movie, music and photo. This will be explained in greater from it. However you can not change a device on the left menu with detail in the following section. the UP/DOWN buttons unless you exit. z The USB device must be compatible with the USB 2.0 standard. z If there is no device listed on the screen after scanning, please check 3) Step 3: Exploring Folders and Files Once you select a content type, i.e., “Movie” and storage or device, i.e.
File Playback Function 2. Contents Playback 2-1. Movie Playback NOTE To play a movie, please select the “Movie” icon on the top menu and z format. select what you want to play on the file list; as explained in the previous section, select a device or storage on the left menu with the z If you want to play the previous or next file as you are watching a movie, please press the PREV or NEXT button. OK button to enter the file list.
File Playback Function 1) Trick Mode Powerful trick-operation is supported while you watching a movie. z PLAY button will display a time-bar. It changes to the normal playback mode while other trick mode is enabled such as PAUSE, FF or REW. z PAUSE button will hold the picture until you play again with the PLAY button. z SLOW FWD button will play in slower speed than the normal speed. The speed will change to x1/2, x1/4, x1/8, x1/16 and x1/32 speed according to each input of the SLOW FWD button.
File Playback Function 2) Subtitle The DP-S1 can decode and display subtitles from a subtitle file. To play You can adjust the position of the subtitle with the UP/DOWN buttons a movie with subtitle, please copy the subtitle file to the same folder of while the subtitle control window is displayed. If the subtitle is out of the movie file and give the same file name as the movie file. The DP-S1 sync, you can adjust the sync with the LEFT/RIGHT buttons.
File Playback Function 2-2. Music Playback You can play music the same way you play a playing movie; please select the “Music” icon on the top menu to play music. You can utilize the same trick operation for playing music which is described in the previous section for playing a movie. You can play the previous or next file with the PREV or NEXT button. NOTE z The DP-S1 plays all music files in a folder repeatedly unless you press the STOP button.
File Playback Function 2-3. Photo Playback To play photo files, please select the “Photo” icon on the top menu. Once the DP-S1 play a photo file, it will play all photos in the folder successively. You can play the previous or next photo manually with the PREV or NEXT button. If you press the INFO button, a help message will display. You can stop the auto-slide show with the PAUSE button and resume with the PLAY button. You can change the slide with the PREV or NEXT button in the manual mode.
File Playback Function 2-4. Play-list NOTE The play-list is a personal collection of multimedia contents, which stores the list of files temporarily. You can organize a separate play-list z If you can not put a folder on the play-list. You have to select all files of a folder and put them to the play-list. for each media content type: movie, music and photo. 1) Add File to Play-list 2) View Files in Play-list You can organize a play-list and enjoy the contents.
File Playback Function 3) Play from play-list 2-5. DVD Playback You can play files in the play-list by pressing the OK or PLAY button. If If you select the “ODD” icon on the left menu while a DVD title is loaded you change to the previous or next file in the play-list, press the PREV on the tray, the DP-S1 will display a confirmation pop-up to play the or NEXT button. title. Please press the OK button to play the DVD title.
Internet Services 7. Internet Services The DP-S1 is designed to support various Internet services, however this will be updated at a later time. You can get the latest information for the DP-SI by visiting the website, www.beyonwiz.com.au.
Advanced Setup 8. Advanced Setup As an extension to Chapter 4. Quick Setup, this chapter illustrates how to configure your DP-S1. The MISCLLANEOUS and MANAGEMENT parts will be explained. In this chapter as they were the remaining two items that were not explained previously. 1. Miscellaneous The setup menu is grouped in four parts: CONFIGURATION, NETWORK, MISCELLANEOUS and MANAGEMENT. The first two groups are explained in Chapter 4. In this chapter the last two parts will be illustrated.
Advanced Setup 1-1. Favorite Before using the favorite service groups, you have to organize them. A favorite group can not contain TV services and radio services together. The edit page consists of three columns: Group, Fav. Service and All Therefore, you have to specify as TV or radio group when you make a Service. Once you enter into the list with the OK button, you can place new group. TV and RADIO icons indicate the property of each group.
Advanced Setup 2) Favorite Service 3) All Service According to your selection of the favorite group in the first column, the The third column shows all services which you can access. This list services belonging to the favorite group will be displayed on the second shows all the service of TV or radio. With the TV/RADIO button, you column. You can remove a service from the favorite group with the OK can change this list to TV service list or radio service list. If you want to button.
Advanced Setup 1-2. Access Control You can set a PIN number to access certain set-up menus. After setting 2) Access Control You can lock the following setup menus. a PIN number, you have to re-enter the PIN number to enter the menu again. 1) Set PIN Number You can set 4-digit PIN number with the NUMERIC buttons. For safety, you have to enter the number twice to set a new PIN number. z Censorship: If you set this, you have to enter the PIN number when you watch a program with higher censorship level.
Advanced Setup z Time Setting Menu: If you set this, you have to enter the PIN number when you change the time and date setting. z Network Configuration Menu: If you set this, you have to enter the PIN number when you change the network configuration. z Service Scan Menu: If you set this, you have to enter the PIN number to scan service. z Factory Setting Menu: If you set this, you have to enter the PIN number to set your DP-S1 as factory-default setting.
Advanced Setup 1-3. Preference 1) Time-shifting If you don’t want to use the time-shifting function, you can disable it. Please select “Time-shifting” and press the OK button. You can select “Disable” on the pop-up menu screen. The default configuration is “Enable”.
Advanced Setup 2. Management You can upgrade or initialize your DP-S1 in this menu. 2) Firmware Upgrade You can upgrade your DP-S1 with the latest firmware. Please visit the website, www.beyonwiz.com.au, for firmware information. If you wish 2-1. F/W Upgrade to upgrade please download the latest firmware. 1) Firmware Information Before upgrading the firmware, you can check the information and last update. Press the OK button to get the information: System Identity, Firmware Version and Last Update.
Advanced Setup After the DP-S1 upgrades the firmware, it will restart automatically. You may check the status on the screen and front display window. NOTE z If you cannot visually see the firmware upgrading from your PC or device, please check the network configuration of your PC and DP-S1. z While the DP-S1 is upgrading the firmware, it should NOT be turned off.
Advanced Setup 2-2. HDD 1) HDD Information 2) HDD Format If you select this menu with the OK button, a pop-up window will You can delete all files on the HDD. If you select this menu with OK display a summary of the internal HDD. You can also check the usage of button, a confirmation pop-up displays. If you select “OK” on the screen the HDD. To close the pop-up window, press the EXIT button. and press the OK button, the DP-S1 will restart and format the HDD automatically.
Advanced Setup 2-3. Initialize 1) Clear Service Information 2) Factory Setting You can clear all the service information. If you select this with the OK If factory setting is selected, the DP-S1 will erase all information and button, a pop-up window will be displayed to get your confirmation. If reset itself to the factory configuration.
Set Remote Control 9. Set Remote Control 2. Manual Set The remote with the DP-SI can control other brands. If you wish to You can set your remote control with 3-digit code manually. Please look control your TV, please press the TV button. After this, the red- at the following table and find the brand of your TV. backlight of the TV button will flash when you press the buttons to Turn on your TV then press and hold the TV button until the red- indicate that the remote control works for your TV.
Set Remote control JVC 207 212 247 264 323 208 215 224 229 253 286 307 344 374 385 387 410 412 205 207 208 215 224 229 248 253 286 389 208 210 211 212 213 214 216 220 230 236 237 239 242 244 245 255 258 260 278 279 286 307 309 384 410 208 244 246 286 287 307 374 376 380 410 205 206 208 209 215 216 218 224 229 253 260 270 277 286 287 296 325 337 374 410 385 LG NEC PANASONIC PIONEER SAMSUNG NOTE z If your TV brand is no
Warranty Conditions Warranty Conditions 1. Where required by Beyonwiz only the original invoice/receipt issued by the dealer will be accepted as proof of purchase. 2. Beyonwiz may reject warranty claims on equipment which it believes to be illegally acquired or when the “owner” is unable to provide proof of purchase or where security labels or serial numbers have been tampered with or removed. 3.
