Welcome Message Welcome Message Thank you for choosing a DP-P2, the High Definition Digital TV Recorder. The DP-P2 supports the true dual-tuner PVR features for the broadcasting programs in HD (MPEG2 1080i). And you can now pause, rewind and record the pay TV with the line-input. You don’t need any tape or DVD for recording. The DP-P2 supports the IceTV Interactive so that you can schedule programs from your PC or mobile phone.
Precaution Precaution Read this manual carefully before using this product. The cautions z Do not repair, disassemble or modify this apparatus yourself. It can described below contain important information about safety, and are cause fire or electric shock. If internal checking or maintenance is categorized into: Danger, Warning and Notice. The company will not be needed, please contact your service center or agency.
Precaution WARNING If the product is mishandled, the user might receiver a serious NOTICE If the product is mishandled, it might cause minor damage. or minor injury. Damage or loss to the user’s property may also occur. z If the apparatus becomes marked, clean it gently with a soft cloth or towel. Never use chemical solvents such as benzene, thinner, acetone z The product must not be exposed to water or liquid. If the apparatus or other solvents.
Precaution About the internal hard disk drive The internal hard disk drive (HDD) is a fragile piece of equipment. Please use the apparatus within the guidelines below to protect against possible HDD failure or to protect against accidental loss. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. z Do not move the apparatus whilst it is on.
Precaution Copyright This manual is protected by copyright laws. Copy, use, reproduction of this manual in part or whole without beyonwiz's prior written permission is prohibited. Disclaimer The manufacturers, distributors and agents are not liable to any kind of damage caused by the use of the information contained in this manual. The instruction and descriptions which this manual contains are based on the time of this manual's production.
Contents Contents Welcome Message i 4. Recommended Configuration 13 4-1. Case 1: Connecting DP-P2 to TV with HDMI 13 4-2. Case 2: Connecting DP-P2 to TV with S-VIDEO 13 Precaution ii Contents 2 1. Package Contents 1 6-1. Connection Using a Network Router 15 6-2. Direct Connection to the PC 16 2. Introduction 3 6-3. Direct Connection to Internet 17 1. DP-P2 Highlights 3 2. Front Panel 4 2-1. Buttons 4 2-2. Slot Door 4 2-3. Front Display Window 4 3. Rear Panel 5 4.
Contents 5. STB & PVR Function 39 1. Basic STB Function 39 1-1. Service Change 39 1-2. Information Box 42 1-3. Volume Level Adjust 43 1-4. Soundtrack Change 43 2. Contents Playback 74 2-1. Movie Playback 74 2-2. Music Playback 78 2-3. Photo Playback 79 2-4. Play-list 80 7. File Management 83 1-5. Subtitle and Teletext Service 44 1-6. Sleep Timer 45 1. Rename 83 46 2. Delete 84 2-1. Service List Edit 46 3. Backup to USB Storage 85 2-2. Favorite Group 47 4.
Contents 10.
Package Contents 1. Package Contents The following elements are included in the gift box. Please check all package contents before using your product. z DP-P2 z Remote Control (BR-02) z Batteries of the Remote Control (AAA size x2) .
This page intentionally left as blank.
Introduction 2. Introduction 1. DP-P2 Highlights World first HD PVR feature The DP-P2 can record two HD (1080i) programs concurrently while you enjoy the time-shifting features. It can also pause, rewind and record a pay TV with the A/V input.
Introduction 2. Front Panel 2-1. Buttons 2-2. Slot Door Five buttons are placed on the front panel. A slot door is placed on the right side of the front panel. If you open this z z z STANDBY Button: it switches the DP-P2 between the operation and door, you can find the following ports; standby modes. z CHANNEL Buttons: the top and bottom parts of the circular button USB: you can connect a USB storage device which is compatible to the USB standard specification.
Introduction 1 2 Indicates hard disk space used. Lights when there is no space left on the HDD. Lights when there is no time information. 3 Lights when a timer recording is programmed in standby mode. 4 Lights when the signal comes out via HDMI. 5 Lights when the signal is High Definition (will be implemented). 6 Indicates the resolution of video output. 7 Lights when the video output is in Progressive Scan mode. 8 Lights when Ethernet connection is set up and enabled.
Introduction 4. Remote Control 4-1. Operating DP-P2 In order to operate the DP-P2 with the enclosed remote control, please select STB mode by pressing the STB button. The red backlight beneath the STB button lights when you press a button in this mode. The below picture and right table show the function of each button on the remote control.
Introduction 4-2. Operating Other Beyonwiz Products The enclosed remote control (Product code: BR-02) is designed to operate the DP-P2 only. To operate other Beyonwiz products of DP-S1, DP-P1 and DP-H1, which are designed to be operated with a remote control of BR-01, you have to change its operating mode; please press and hold the numeric button 1 for 5~6 seconds while pressing the OK button.
Introduction 4-3. Operating TV set 2) Manual Set The enclosed remote control can also be used to control a TV set You can set your remote control with 3-digit code manually. Please look provided by major TV manufacturers. In order to operate a TV with the at the following table and find the brand of your TV. enclosed remote control, please select TV mode by pressing the TV Turn on your TV then press and hold the TV button until the red- button.
Introduction JVC 207 212 247 264 323 z 385 LG NEC PANASONIC PIONEER SAMSUNG NOTE 208 215 224 229 253 286 307 344 374 385 387 410 412 205 207 208 215 224 229 248 253 286 389 208 210 211 212 213 214 216 220 230 236 237 239 242 244 245 255 258 260 278 279 286 307 309 384 410 208 244 246 286 287 307 374 376 380 410 205 206 208 209 215 216 218 224 229 253 260 270 277 286 287 296 325 337 374 410 If your TV brand is not lis
Introduction 4-4. Remote Control HEXA Code The below picture and right table inform you to set your own remote control to operate the DP-P2. The coding system used for the DP-P2 is the NEC type.
How to Connect 3. How to Connect 1. Connect to TV Depending on your A/V equipment including TV set which you would like To connect your DP-P2 to your TV or audio system, you have the to connect to, there are various ways you can connect the DP-P2 and following options; A/V equipment. To make the best connections, please refer to the manual of your TV set, stereo system or other equipment which you z S/PDIF Digital Audio output (COAXIAL, OPTICAL) would like to connect to.
How to Connect 2. A/V Inputs 3. A/V Bypass The DP-P2 has A/V input ports for connecting other A/V device such as In the standby mode, the DP-P2 is designed to bypass the video and a set-top box. You can record or enable the time-shifting functions for a audio signals from the external A/V device connected to the A/V input pay-TV service with the DP-P2. ports to TV set through the Composite, S-VIDEO and Analog Audio output ports.
How to Connect 4. Recommended Configuration 4-1. Case 1: Connecting DP-P2 to TV with HDMI 4-2. Case 2: Connecting DP-P2 to TV with S-VIDEO If you connect the DP-P2 to TV set with the HDMI connection, please If you connect the DP-P2 to TV set with the S-VIDEO (or Composite) connect the DP-P2 and the TV set with the S-VIDEO (or Composite) and connection, you can watch the external A/V signal without turning on Analog Audio ports, too.
How to Connect 5. Antenna Connection Please connect your TV Antenna to the DP-P2. z Antenna In (connecting to the roof Antenna) z RF LOOP OUT (only for bypassing the signal to another device) NOTE z Two tuners are connected internally: You don’t need to connect them with a additional cable.
How to Connect 6. Ethernet Connection 6-1. Connection Using a Network Router In order to utilize the DP-P2 fully, it is strongly recommended to As shown in the picture, you have to connect the DP-P2 to the router connect the DP-P2 to the home network with a network router. with an Ethernet cable included in the box.
How to Connect 6-2. Direct Connection to the PC With this configuration, you can share contents with a PC through home If your PC has the DHCP server feature and it is enabled, all the network but the DP-P2 can not access to Internet. For this connection, configurations for networking will be set automatically and the DP-P2 is the following equipment is required; ready to communicate with your PC.
How to Connect 6-3. Direct Connection to Internet With this configuration, you can not share contents with a PC through home network. For this connection, a crossed Ethernet cable (not included in the box) is required. The most ISP (Internet Service Provider) services DHCP feature. Therefore, you can connect your DPP2 to Internet with a crossed cable and enjoy it. If you have to configure your DP-P2 manually, please contact your ISP for more information.
This page intentionally left as blank.
Quick Setup 4. Quick Setup This chapter guides you through the basic set up of the DP-P2 so that NOTE you can experience its basic feature. In order to enjoy the DP-P2 fully, z please refer to Chapter 9. Advanced Setup. If the front display shows “Service Scan”, you have to scan the broadcasting services first. Please refer to the next section of scanning services. 1. Start Quick Setup If A/V and antenna connection is complete, press the STANDBY button to start.
Quick Setup 1-1. Quick Setup of Video Output Format If the front display window indicates that the DP-P2 is ready to use but NOTE nothing displays on the TV screen, you have to adjust the format and z The TV-OUT button is developed so that you can configure the video resolution of the video output by pressing the TV-OUT button. The output of the DP-P2 when you can not see anything on the TV screen default video output is in a SD PAL (576i) format.
Quick Setup 1-2. Basic Operation 1) Enter and Exit Setup Menu You can enter the SET-UP MENU with the SET-UP button on the remote control and exit to watch the TV program with the EXIT button. 2) Setup Menu Structure The SET-UP menu is grouped in four parts: CONFIGURATION, NETWORK, MISCELLANEOUS and MANAGEMENT. Firstly, you have to choose one of these categories (main category) which are placed on the top menu (a horizontal bar) as graphical icons.
Quick Setup 3) How to Change Configuration In the setup menu, there are several ways to change the configuration. z Setup using the NUMERIC buttons: The NUMERIC buttons are used This manual explains how to change the configuration, here are three to set a configuration with numbers such as time information. You can cases which are used frequently. also move the cursor to left or right with the LEFT of RIGHT buttons whilst you are editing the configuration.
Quick Setup z On-screen keyboard: If you need to input alphabetic characters, an on-screen keyboard will be displayed. You can move the cursor with the UP/DOWN/LEFT/RIGHT buttons and select the letters with the OK button. The RECALL button works as a backspace key. You can also clear your inputs by selecting “Clear All” with the OK button on the screen. You can move the cursor to left or right with the YELLOW or BLUE buttons. After the input, you can save it by selecting “Save & Exit” with the OK button.
Quick Setup 2. Configuration 2-1. Time Setting Please set the current date and time. The date and time information will z “DD/MM/YYYY”, “MM/DD/YYYY” or “YYYY/MM/DD” on a pop-up menu. be the reference for the timer recording. Therefore, you have to (DD-day, MM-month, YYYY-year) configure the time and date information precisely. You can also select preferred date and time formats.
Quick Setup z Current Time: Under the “MANUAL” mode, you have to set the date and time manually using the numeric buttons or CH +/- buttons. NOTE z Under the “AUTO” mode, the GMT information can be received automatically from DTV station when you turn on the DP-P2 and watch a program. Please note that some DTV stations don’t send the GMT information or send wrong information. z Your selected date and time format will be applied to all the date and time displayed on the graphical menus.
Quick Setup 2-2. A/V Output Setting You have to set the video and audio configuration according to your TV 1) Video Outputs z support the PAL format in Australia. set. Please make sure the video and audio port of the DP-P2 is connected to your TV set. z z Resolution: If you select the HDMI or Component for Video output, you have to set the resolution. outputs with pop-up menu. Please press the OK button to get a pop-up menu for each item.
Quick Setup 2) Audio Outputs 3) Colour Setting The DP-P2 supports Dolby Digital decoding so that it can decode and You can adjust the colour output of the DP-P2. output the Dolby sound through the RCA connectors. It also supports digital outputs with optical and coaxial ports. z Audio Format: The DP-P2 has 2ch analog audio outputs for a stereo speaker system. But it can transmit audio signal up to 5.1ch through digital audio outputs if the content has 5.1ch audio source.
Quick Setup 2-3. Service Scan z Antenna DC (+5V) Power: You can supply DC (+5V, max. 100mA) Before watching a broadcasted program, you need to scan all the power to the indoor antenna through the antenna cable. Please make services first. The scanned services will be stored in the non-volatilize sure that your external antenna is an active type, which means that memory.
Quick Setup z Start Scan: After selecting your scanning range, you can “start NOTE scanning”. Select Start Scanning and then press the OK button. On z You can not select an end channel smaller than the start channel. the screen, the scanning window appears and displays the process. z If you scan over all the channels with the “FULL” option, the previous service information including the service list information and your favorite lists will be erased automatically.
Quick Setup 2-4. A/V Input You need to configure the A/V input ports according the external A/V device connected to the DP-P2. z Input: The DP-P2 can receive either the Composite or S-VIDEO signal at a time. Therefore you need select one of these according to the video input connection. z Video Type: You need to set the video type according to the external A/V device.
Quick Setup 3. Network The DP-P2 supports an Ethernet interfaces. This section will guide you how to configure the network interfaces. 3-1. Ethernet Setting The first step is to enable the Ethernet interface. You can select this in the Network Device menu. You will get a pop-up menu by pressing the OK button. If you want to use the Ethernet interface, please select the “LAN” option. If you select “Disable” option, the Ethernet interface will be disabled even though you configure it properly.
Quick Setup 3-2. Automatic Configuration If you enable the Ethernet interface by selecting the “LAN” option on the “Network Device” menu, all the items to be configured for the Ethernet interface will be displayed. You can also get the pop-up window and check the current effective configuration of the Ethernet interface with the GREEN button. z DHCP: If you want to get the all the configuration from the router and set automatically, please select the “Enable” option.
Quick Setup 3-3. Manual Configuration If you select the “Disable” option in the “DHCP”, you have to input the z interface but you can not change it. IP address manually. z IP Address: You can input the address with the NUMERIC buttons NOTE and the LEFT/RIGHT buttons. You can move to the next item of z You can configure the following items in the same way; Subnet Mask, You have to press the RED button to make your changes and configurations for the network interface to take effect.
Quick Setup 3-4. Ice Guide The DP-P2 supports IceTV service through the Internet. If you have an z displayed and you can enter your ID of IceTV account. IceTV account, please set your account to utilize the service on your DPP2. Owner ID: If you press the OK button, on-screen keyboard will z Password: If you press the OK button, the on-screen keyboard will displayed and you can enter your password. z Check User Info: You can check if your account information is valid or not.
Quick Setup 3-5. WizPNP The WizPNP enables to share the recording files with other beyonwiz NOTE products or PCs. z You need an application software for your PC to connect to the DP-P2. Please visit to www.beyonwiz.com.au and download “WizFX” software. z The WizPNP server can not get a file from a WizPNP client. z The WizPNP client can play recording files from a WizPNP server. Please refer to Chapter 6. File Playback Function for details.
Quick Setup 1) Set as WizPNP Client 2) Set as WizPNP Server You can set the DP-P2 as a WizPNP client; please select the “Client” You can set the DP-P2 as a WizPNP server; please select the “Server” menu with the OK button and select “Enable” with the OK button. You menu with the OK button and select “Enable” with the OK button. You can also disable the WizPNP client function by selecting “Disable” with can also disable the WizPNP server function by selecting “Disable” with the OK button.
Quick Setup 3-6. Windows Sharing You can set account information of the ID and password to share files in the shared folder on your PC, which is blocked to access for the “Guest” account and requires an ID and password to access. You also have to set account information to backup the recording files on the DP-P2 to the PC via network; the “Guest” account is not allowed to copy files to the shared folder.
This page intentionally left as blank.
STB & PVR Function 5. STB & PVR Function The DP-P2 supports various ways of enjoying multimedia contents and it groups its features in three parts; the first group is STB (Set-top Box) and PVR (Personal Video Recorder) functions, the second group is file 1. Basic STB Function 1-1. Service Change playback functions including playback of recorded programs with PVR function, and the last group is Internet services which will be updated 1) Change between TV and Radio Services later.
STB & PVR Function 2) Change Service with Service List The service list contains all the broadcasting services you can receive. You can also edit the service list in the list view. This will be explained in You can get the service list as a pop-up menu by pressing the LIST the later section. button and select a service with the UP/DOWN buttons. NOTE z You can hide the help message and extend the service list with the RED button.
STB & PVR Function 3) Other Ways to Change Service As in conventional TV sets, you can change a service which you want to NOTE watch or listen to in the following ways; z If you change a service continuously with the CH+ or CH- button, only the information box will be changed according to your command: z Service Change with the CH+/CH- buttons: As you press the CH+ or You can watch the changed service 3 seconds after you press the last CH- button, the next or previous service will be selected.
STB & PVR Function 1-2. Information Box You can check the information of a service and the program using three information boxes; the information box contains specific information of a current service and program. The extended information box contains more details about the current program. And the recording information box shows the recording status. You can check these by pressing the INFO button and cancel it by pressing the EXIT button.
STB & PVR Function 1-3. Volume Level Adjust 1-4. Soundtrack Change With the VOL+/VOL- buttons, you can adjust the volume level of the If the current TV program provides more than one language or audio analog audio output. The MUTE button will turn off the analog and format, i.e. MPEG audio and Dolby audio, together, you can select one digital audio outputs. and change to that setting whilst you are watching a TV program.
STB & PVR Function 1-5. Subtitle and Teletext Service 1) Subtitle Service 2) Teletext Service If you want to view subtitles on the screen, please press the SUBTITLE The teletext is a free service broadcasted by TV stations which gives the button. To display the subtitle, please select “Enable” and press the OK latest information on news, weather, television programs, share prices button. You can hide the subtitle by selecting “Disable” with the OK and many other topics.
STB & PVR Function 1-6. Sleep Timer You can set the DP-P2 to turn off automatically at a specific time. Press NOTE the SLEEP button to set the timer. The DP-P2 will only turn off after a z recording has finished even if you set it to turn off before the The pop-up menu also contains the above functions of the Subtitle Language, Sound Track, Teletext and Sleep timer. completion of the current recording(s). To cancel the timer, please press the SLEEP button successively until you set time as “0 min”.
STB & PVR Function 2. Service Edit 2-1. Service List Edit z You can edit the service list if you want. The followings illustrate the Lock/Unlock: For your privacy, you can protect certain service from unauthorized access. If you lock a marked service with the GREEN editing functions you can use to edit a service list. button, you have to enter the 4-digit PIN code to watch the service. The LOCK icon implies that the marked service is locked.
STB & PVR Function 2-2. Favorite Group Favorite group is your personal collection of TV or radio services. You can organize up to 20 groups including three default groups. 1) Favorite Group Edit Before you use the favorite service groups, you have to organize them. Please refer to Chapter 8. and organize your own favorite group(s). 2) Select Service on Favorite Group Once you organize favorite groups, you can change the services that belong to a certain favorite group.
STB & PVR Function 4) Service Change on Favorite Group If you change services using the service list when you select a favorite You can also exit from the favorite list by pressing the RED button when group, the service list will show the services belong to that favorite the favorite list is displayed. group. You can change among these services on the list.
STB & PVR Function 3. PVR Functions The major functions of a PVR are time-shifting and recording. If you z the picture at time-shifted position. want to play a recorded program, please use the multimedia contents playback function with the FILE PLAY button on the remote control. STOP button will skip and jump to the live position when you watch z SLOW FWD button will play the recording in slower speed. The speed Chapter 6.
STB & PVR Function You can jump to a certain position with the LEFT/RIGHT/UP/DOWN You can also display the progress bar with the OK button. The OK buttons. button can also hide the progress bar. z LEFT/RIGHT buttons skips and moves backward or forward 15 seconds at a time respectively.
STB & PVR Function 3-2. A-B Repeat 3-3. Bookmark The DP-P2 can play a certain section (A-B) repeatedly. You can set bookmarks to retrieve it easily. Please activate the progress bar with the OK button. Place the lower z RED button sets a bookmark at the current point. anchor mark at the start position and press the YELLOW button. A new z Green button seeks and plays from the bookmarked position. anchor mark with “A” will indicates the start position.
STB & PVR Function If you want to set multiple bookmarks, it is better to activate the The BLUE button will display a list of bookmarks. Please select one item progress bar with the OK button. To set a bookmark, please place the and press the OK button. The DP-P2 starts to play from the selected anchor mark on the position you want to play and press the RED button. position. A dot mark indicates that one bookmark is set.
STB & PVR Function 3-4. Instant Recording 1) Start Recording You can record the current service and store it in the HDD instantly by z Starting Point: You can select the starting point of recording with the pressing the REC button. The following picture shows options you can LEFT/RIGHT buttons when the time-shift function is enabled. If the choose when you record a program. time-shift function is disabled, you can only record from the current time.
STB & PVR Function NOTE z If you disable the time-shifting function, you can’t record a program from the time-shifting buffer. Therefore you can only choose a single option of “Live” when you intend to record a program. z If there is only one program in the time-shift buffer, two options of “Current Program” and “All” have the same meaning. Therefore option “Current Program” does not appear.
STB & PVR Function 2) Trick Mode Operation If you are watching a program whilst it is being recorded, you can perform the same trick mode operations including “A-B Repeat”, which are explained in the previous sections, even though you are recording two programs simultaneously. For more information of trick-mode operating, please refer to the previous sections.
STB & PVR Function 3) Pause/Resume and Stop Recording If you want to skip recording for a certain period of time, i.e., NOTE commercial advertisements, please press the REC button whilst you are z watching the recording service. Once a pop-up page appears, please press the PAUSE button. You can resume recording with the PAUSE button. To stop a recording before it stops automatically after the duration, please press the STOP button when the recording control pop-up is displayed.
STB & PVR Function 4) Change Recording Options whilst Recording You can change the duration of a recording or file name after the Please select a recording item with the UP/DOWN buttons to change. recording has started. You can also lock or unlock the recording file If there is one recording, only one item will be displayed. whilst you are recording the service. Press the POP-UP button and select “Recording Information” with the OK button. z You can change the duration with the LEFT or RIGHT button.
STB & PVR Function 3-5. Timer You can set programs which you would like to record to HDD. The timer function can also be used to turn on the DP-P2 and watch the set program or transmit the picture to an external recording device such as a VCR (Video Cassette Recorder) according to your timer reservations. You can set up to a maximum 100 timers. 1) View Timer List You can view and check all of the timer information; modifying or delete a timer and add a new timer to the timer list.
STB & PVR Function 2) Add New Timer To add a timer, please press the RED button to display a menu on the screen. A new pop-up window will appear to configure the timer. You can configure the following items with your preference for a new time record. z Date: Set start date of recording. Move cursor with the LEFT/RIGHT buttons and change date with the NUMERIC buttons. z Start Time: Set start time. Move cursor with the LEFT/RIGHT buttons and change time with the NUMERIC buttons.
STB & PVR Function 3) Edit Timer z z z Mode: If you would like to watch a certain program or transfer it to an You can modify a timer setting such as service, start date, start time, external recorder instead of recording it to HDD, please choose “View” duration, recurrence and mode. Please choose a timer with the option with the LEFT/RIGHT buttons. If you want to record a UP/DOWN buttons on the timer list and press the OK button to change. program, please select “Record” option.
STB & PVR Function 4) Delete Timer 5) Turn On and Off the DP-P2 according to Timer Select a timer which you want to delete with the UP/DOWN buttons If a timer starts when the DP-P2 is in standby mode, the DP-P2 is and press the GREEN button. A pop-up confirmation will appear and turned on automatically and performs its operation according to the choose “Yes” with the OK button. If you do not want to delete a timer, timer.
STB & PVR Function 3-6. Recording Conflict 1) Duplication When a New Timer Sets The DP-P2 can record up to two programs simultaneously. If you intend You can not add a new timer to record three programs at the same time. to record more than two programs simultaneously, a warning pop-up of If this occurs, a pop-up list is displayed to show the list of duplicated duplication will be displayed. timers if a new timer is entered as duplication.
STB & PVR Function 2) When New Recording Starts 3) New Timer Overlaps Existing Timer If a new recording starts according to a timer whilst the DP-P2 records Because the DP-P2 checks recording conflict only with timers when you two programs simultaneously, the following pop-up will be displayed. set a new timer, you can set a new timer which records and overlaps the same program being recorded. In this case, conflict will occur when a new recording starts according to the timer.
STB & PVR Function NOTE z The new recording has higher priority than the existing recordings. Therefore, when a new recording starts it will stop one of the existing recordings, which ends earlier respectively, if there are no confirmation or cancellation. z You may not notice the warning message so make sure you organize the timer list properly specifically if you are recording a very important program.
STB & PVR Function 4. EPG (Electronic Program Guide) 4-1. EPG with Multiple Services The EPG (Electronic Program Guide) is a time table of TV programs This EPG shows 6 services at a time. The vertical axis implies services which show upcoming programs on a network. The EPG information is and the horizontal axis implies time.
STB & PVR Function 4-2. EPG with Single Service This EPG shows only one service at a time. You can change to the NOTE multiple-service EPG with the RED button. Programs are listed vertically z The thumb-nail window displays the program you watched before you by time. Therefore you can move cursor to the previous or next entered the EPG. The screen will not change when you change the program with the UP/DOWN buttons.
STB & PVR Function 4-3. Service Change and Recording 1) Service Change and Instant Recording If you press the OK button whilst the cursor is placed on the current NOTE program (not a future program), a new pop-up will be displayed. Please z unless you cancel one of two recordings. select “Watch” option to watch the selected program on the thumb-nail screen. To record the select program, please select “Record” option.
STB & PVR Function 2) Set timer recording If the cursor is placed on a future program, the REC or OK button sets If you set a timer on the EPG, the recurrence of the timer sets as a timer and the colour of types changes to red to indicate that the “Once” automatically. You can change the recurrence or edit the timer program is reserved to be recorded. If a certain cell in the EPG has red with the REC button in the EPG. colour, that program is reserved to be recorded.
File Playback Function 6. File Playback Function This chapter covers all functions regarding playing multimedia contents. The DP-P2 can play movie, music and photo files stored in the internal hard disk drive, PCs on the home network, USB storage devices, and memory cards. You can also play the recording contents in this mode. You can enter this operation mode with the File PLAY button. 1.
File Playback Function 2) Step 2: Select Storage With the UP/DOWN buttons, you can select a device to access. As you select a device, folders and files stored in that device will be listed on the screen. There are five icons on the left menu and each icon has the following meanings: z HDD: You can access the internal hard disk drive by choosing “HDD” icon. The recorded programs of TV and Radio will be stored in the “Recording” folder.
File Playback Function The “PC” icon indicates the PC and the “STB” icon indicates the NOTE WizPNP server. z If there is no device listed on the screen after scanning, please check the network connection and make sure its set and configured properly. z If you want to clear the list of network devices, Please press the YELLOW button. z USB: You can access any USB devices connected to the DP-P2 by selecting “USB” icon on the left menu.
File Playback Function WARNING z Each USB port can supply maximum of 500mA to the external device. Connecting devices consuming more than 500mA can damage the DP-P2 if there is no additional power supplier to the USB device. z The USB device should be detached properly to prevent the DP-P2 from unstable operation or damage. Please press the RED button to detach the selected USB device properly.
File Playback Function 3) Step 3: Exploring Folders and Files Once you select a content type, i.e., “Movie” and storage or device, i.e., NOTE “Network”, press the OK button to enter the list of folders and/or files z There are two operation modes for exploring contents; in the first (the file list). In the file list, the UP/DOWN buttons move the cursor operation mode, you can select an icon (content type) on the top upward or downward to select a folder or file.
File Playback Function 2. Contents Playback 2-1. Movie Playback To play a movie, please select the “Movie” icon on the top menu and NOTE select what you want to play on the file list; as explained in the z format. previous section, select a device or storage on the left menu with the OK button to enter the file list. You can choose a file or folder with the z If you want to play the previous or next file as you are watching a movie, please press the PREV or NEXT button.
File Playback Function 1) Trick Mode Powerful trick-operation is supported whilst you watching a movie. z PLAY button will display a time-bar. It changes to the normal playback mode whilst other trick mode is enabled such as PAUSE, FF or REW. z PAUSE button will hold the picture until you play again with the PLAY button. z SLOW FWD button will play in slower speed than the normal speed. The speed will change to x1/2, x1/4, x1/8, x1/16 and x1/32 speed according to each input of the SLOW FWD button.
File Playback Function 2) A-B Repeat The DP-P2 can play a certain section (A-B) repeatedly. NOTE z Please activate the progress bar with the OK button. Place the lower anchor mark at the start position and press the YELLOW button. A new anchor mark with “A” will indicates the start position. Move the lower anchor mark at the end position and press the YELLOW button. A new anchor mark with “B” will be displayed and stat to play from “A” to “B” automatically.
File Playback Function 3) Subtitle The DP-P2 can decode and display subtitles from a subtitle file. To play z UP/DOWN buttons whilst the subtitle control window is displayed. a movie with subtitle, please copy the subtitle file to the same folder of the movie file and give the same file name as the movie file. The DP-P2 Subtitle Position: You can adjust the position of the subtitle with the z Time Sync: If the subtitle is out of sync, you can adjust the sync with the LEFT/RIGHT buttons.
File Playback Function 2-2. Music Playback You can play music the same way you play a movie; please select the “Music” icon on the top menu to play music. You can utilize the same trick operation for playing music which is described in the previous section for playing a movie. You can play the previous or next file with the PREV or NEXT button. NOTE z The DP-P2 plays all music files in a folder repeatedly unless you press the STOP button.
File Playback Function 2-3. Photo Playback z Show and Hide Help Message: If you press the INFO button, a help message will be hided. You can also display the help message with To play photo files, please select the “Photo” icon on the top menu. the INFO button. z Rotation: You can rotate the photo with the RED and GREEN buttons. z Change Interval: You can change the time interval in the auto slide show. As you press the UP and DOWN buttons, the time interval will be changed.
File Playback Function 2-4. Play-list The play-list is a personal collection of multimedia contents, which NOTE stores the list of files temporarily. You can organize a separate play-list z for each content type: movie, music and photo. If you can not put a folder on the play-list, you have to select all files of a folder and put them to the play-list. 1) Add File to Play-list You can organize a play-list and enjoy the contents.
File Playback Function 3) Play from play-list 4) Remove File from Play-list You can play files in the play-list by pressing the OK or PLAY button. If You can remove a file from the play-list with the YELLOW button the you change to the previous or next file in the play-list, press the PREV same way as adding a file to a play-list. Select the “PLAY-LIST” icon on or NEXT button. the left menu and choose a file which you want to remove from the play-list.
This page intentionally left as blank.
File Management 7. File Management 1. Rename You can rename a recording file stored on the onboard HDD. Please select a file on the FLIE PLAY menu and press the POPUP button. A list NOTE z You can not rename more than one file with the same name at the of extended menus will be displayed. Please select “Rename” menu with same time. Therefore, the “Rename” menu will be disabled if you the OK button. select more than one file. You can edit the file name with the on-screen keyboard.
File Management 2. Delete You can delete the recording files stoned on the onboard HDD. Please NOTE select a file on the FLIE PLAY menu and press the POPUP button. A list z You can delete more than one file at the same time. Please select files of extended menus will be displayed. Please select “Delete” menu with to delete with the BLUE button. The check mark indicates that the file the OK button. is selected. You can also unselect the file with the BLUE button.
File Management 3. Backup to USB Storage You can copy or move the recording files to a USB storage device such The estimated time information is displayed and you can decide if you as a USB HDD. Please select a file on the FLIE PLAY menu and press the proceed or cancel according to the time information. POPUP button. A list of extended menu will be displayed. Please select “Copy to” or “Move to” menu with the OK button. NOTE z A USB storage device is not included in the gift box.
File Management If you confirm, two options will be displayed. Please select “USB” with The USB storage devices connected to the DP-P2 will be listed. Please the OK button. The USB storage devices connected to the DP-P2 will be select one with the OK button. listed. Please select “USB” with the OK button. NOTE z 86 If you want to create a new folder, please press the GREEN button.
File Management The RED button will copy or move the files to the selected folder. A progress-bar indicates the status. NOTE z If you cancel to copy or move files, please press the EXIT button. z In order to watch a TV program, please press the LIVE or RECALL button.
File Management 4. Backup to PC via Network You can also copy or move the recording files to a PC connected to your All the network devices connected to your home network will be listed. home network. Please select a file on the FLIE PLAY menu and press the Please select one with the OK button. POPUP button. A list of extended menu will be displayed. Please select “Copy to” or “Move to” menu with the OK button. All the remaining procedure is same as copying to the USB storage.
File Management 5. Edit Recording File You can edit the recording file whilst you play a recording file on the z Cut out: you can cut and delete the selected part. FILE PLAY menu. z Save a copy as: you can make a copy for the selected part. z Crop: you can cut and delete the unselected part. z Cut and Save: you can cut out the selected part from the original file and make a new file with the selected part. A progress bar indicates the status. Please activate the progress bar with the OK button.
This page intentionally left as blank.
Internet Service 8. Internet Service The DP-P2 is designed to support various Internet services, however this will be updated at a later time. You can get the latest information for the DP-P2 by visiting the website, www.beyonwiz.com.au.
This page intentionally left as blank.
Advanced Setup 9. Advanced Setup As an extension to Chapter 4. Quick Setup, this chapter illustrates how to configure your DP-P2. The MISCELLANEOUS and MANAGEMENT parts will be explained. In this chapter as they were the remaining two items that were not explained previously. 1. Miscellaneous The setup menu is grouped in four parts: CONFIGURATION, NETWORK, MISCELLANEOUS and MANAGEMENT. The first two groups are explained in Chapter 4. In this chapter the last two parts will be illustrated.
Advanced Setup 1-1. Favorite Before using the favorite service groups, you have to organize them. A favorite group can not contain TV services and radio services together. The edit page consists of three columns: “Group”, “Fav. Service” and “All Therefore, you have to specify as TV or radio group when you make a Service”. Once you enter into the list with the OK button, you can place new group. TV and RADIO icons indicate the property of each group.
Advanced Setup 2) Favorite Service 3) All Service According to your selection of the favorite group in the first column, the The third column shows all services which you can access. This list services belonging to the favorite group will be displayed on the second shows all the service of TV or radio. With the TV/RADIO button, you column. You can remove a service from the favorite group with the OK can change this list to TV service list or radio service list. If you want to button.
Advanced Setup 1-2. OSD 1) Help Box Display 2) Transparency You can hide the help box which is displayed with the service list. If you You can set the transparency of the OSD. Please press the OK button to set this option as “Hide”, the help box does not appear when you press display the options of the transparency. After selecting an option with the LIST button. the UP and DOWN buttons, please press the OK button to set the change.
Advanced Setup 3) Colour Theme The DP-P2 provides 10 colour themes on your taste.
Advanced Setup 1-3. Access Control You can set a PIN number to access certain set-up menus. After setting 2) Access Control a PIN number, you have to re-enter the PIN number to enter the menu You can lock the following setup menus. again. 1) Set PIN Number You can set 4-digit PIN number with the NUMERIC buttons. For safety, you have to enter the number twice to set a new PIN number. z Censorship: If you set this, you have to enter the PIN number when you watch a program with higher censorship level.
Advanced Setup z z Time Setting Menu: If you set this, you have to enter the PIN number 1-4. Preference when you change the time and date setting. 1) Time-shifting Network Configuration Menu: If you set this, you have to enter the PIN number when you change the network configuration. z Service Scan Menu: If you set this, you have to enter the PIN number to scan service.
Advanced Setup 2) Soft Padding The soft-padding function is designed to set additional time to the The Pre-padding means the additional time set prior the program and recording period if you set a timer on the EPG menu. the Post-padding means the additional time set after the program.
Advanced Setup 3) Keyboard Order Event though timer-conflict occurs according to the soft padding, timer- You can enter numbers or alphabet characters with the NUMERIC conflict message does not display; the DP-P2 will resolve conflicts buttons. If you set the Keyboard order as “ABC2”, the NUMERIC button automatically according to the soft-padding priority. will enter in the following sequence; A Æ B Æ C Æ 2. .
Advanced Setup 2. Management You can upgrade or initialize your DP-P2 in this menu. 2-1. F/W Upgrade 1) Firmware Information 2) Firmware Upgrade You can upgrade your DP-P2 with the latest firmware. Please visit the Before upgrading the firmware, you can check the information and last website, www.beyonwiz.com.au, for firmware information. If you wish update. Press the OK button to get the information: System Identity, to upgrade please download the latest firmware. Firmware Version and Last Update.
Advanced Setup If you select the “Network” option, the PCs and network devices If you select the “Memory Card” or “USB” option, a list view will be connected to your home network will be displayed. If you can not see displayed. any device on the list view, please press the RED button to scan the devices. You can also scan a specific network device with its IP address. Please press the GREEN button and enter the IP address.
Advanced Setup Please select the firmware on the file list and press the OK button to start. It takes several minutes to complete upgrading. Please make sure that your DP-P2 is NOT turned OFF until it finishes upgrading. NOTE z If you cannot visually see the firmware upgrading from your PC or device, please check the network configuration of your PC and DP-P2.
Advanced Setup 2-2. HDD 1) HDD Information 2) HDD Format If you select this menu with the OK button, a pop-up window will You can delete all files on the HDD. If you select this menu with OK display a summary of the internal HDD. You can also check the usage of button, a confirmation pop-up displays. If you select “OK” on the screen the HDD. To close the pop-up window, press the EXIT button. and press the OK button, the DP-P2 will restart and format the HDD automatically.
Advanced Setup 3) Check HDD If the DP-P2 is turned off improperly, it is strongly recommended to check the onboard HDD. Please press the OK button to check the HDD. NOTE z When you turn the DP-P2 on after it is turned off improperly, a warning message guide you to check the onboard HDD. It takes several minutes to check the HDD. z Whilst the DP-P2 checks the onboard HDD, the PVR functions are disabled and you can only watch TV service or listen radio service.
Advanced Setup 4) Format USB Storage In order to copy the recording files to a USB storage device, it should be WARNING formatted first. Please select “Format USB HDD” menu with the OK button. A list of USB storage devices will be displayed. Please press the z If you format the USB storage device, all the data stored in the USB storage device will be erased. OK button to format the selected one. It takes several minutes to format.
Advanced Setup 2-3. Initialize 1) Clear Service Information 2) Factory Setting You can clear all the service information. If you select this with the OK If factory setting is selected, the DP-P2 will erase all information and button, a pop-up window will be displayed to get your confirmation. If reset itself to the factory configuration.
Advanced Setup 3) Clear IceGuide Disk Cache The EPG information from the IceTV is stored on the HDD. You can clear the EPG information and receive the data from the IceTV server.
Troubleshooting Guide z 10. Troubleshooting Guide Make sure that the antenna cable is correctly connected to the product. The remote with the DP-P2 can control other brands. If you wish to z Check the brightness level of TV. z Check if the channel is currently on air.
Troubleshooting Guide strength and/or quality is optimal. No sound, or poor z sound z z If not, front panel of the DP-P2 has been removed. please contact an authorized antenna service Remote control agent or licensed contractor to seek advice does not operate control, the Remote control's emitter should concerning improving your TV reception. TV directly point towards the product's Remote z Check the Volume status of the product, TV control receiver. and other audio device/s.
Troubleshooting Guide z EPG data is not z present in the Guide, or the EPG z Check to ensure that the other devices on your Unable to use “trick network are configured correctly to connect mode” functions with another network device. with live TV z Check if Time Shift is enabled. (Setup\Miscellaneous\Preferences) z Ensure the Time Shift buffer contains enough data to execute the desired function. Do you have an account subscription with an EPG data provider? (eg.
Troubleshooting Guide This page intentionally left as blank.
Specification Specification Video & Audio Decoding Main System Main Processor HDD RISC CPU 320GB Tuner & Channel Decoder Dual Tuner Tuner Input Conn. Tuner Loop-through Conn. Frequency Range Signal Level Aerial Supply DVB-T Compliant (Internal Loop-through) IEC 169-2 Female Type IEC 169-2 Male Type 174~230MHz, 470~860MHz -20 ~ -80dBm 5V, max.
Warranty Conditions Warranty Conditions 1. Where required by Beyonwiz only the original invoice/receipt issued by the dealer will be accepted as proof of purchase. 2. Beyonwiz may reject warranty claims on equipment which it believes to be illegally acquired or when the “owner” is unable to provide proof of purchase or where security labels or serial numbers have been tampered with or removed. 3.
WEEE Information WEEE Information Correct Disposal of This Product (Waste Electrical & Electronic Equipment) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Contact Beyonwiz Contact Beyonwiz Beyonwiz Australia support@beyonwiz.com.au www.beyonwiz.com.au Some features and information in this manual may differ slightly from the product itself due to firmware version and changes made after printing.
