Specifications

Code Trade
HONEYWELL (1 Year Warranty) (continued)
76
WIN-PAK 2005 CONFIGURATION
Note: All the controllers below require a PSX220 Transformer (922-0213) and a separate suitable PSU for any locking devices
N-1000 Series Control Panels (For use with WIN-PAK 1.16, WIN-PAK 2,
WIN-PAK 2005, WIN-PAK PRO 2005 & WIN-PAK PRO CS Software)

NEW 911-0381 N1000-III 2 reader controller with lockable enclosure and tamper switch. Includes 12V battery backup

NEW 911-0382 N1000-III-CB 2 reader controller (PCB only)

NEW 911-0383 N1000-III-X Expanded 2 reader controller with lockable enclosure and tamper switch. Includes 12V battery backup

NEW 911-0384 N1000-III-X-CB Expanded 2 reader (PCB only)

NEW 911-0389 N1000-IV 4 reader controller with lockable enclosure and tamper switch. Includes 12V battery backup

NEW 911-0390 N1000-IV-CB 4 reader controller (PCB only)

NEW 911-0391 N1000-IV-X Expanded 4 reader controller with lockable enclosure and tamper switch. Includes 12V battery backup

NEW 911-0392 N1000-IV-X-CB Expanded 4 reader controller (PCB only)
Note: All N-1000 series panels have 4 relay outputs and 16 inputs.
Control Panel Accessories (N-1000 & PW Series)

NEW 922-0213 PSX220 230VAC/16.5VAC & 11.5VAC Combo Transformer for use with N-1000-III/IV, PW-2000-III/IV Access control panels, and PRO22ENC3 &
PRO22ENC4 access control panels

NEW 927-2234 S4 Suppressor kit. Provides protection against electrical spikes caused by collapsing electrical fields

NEW 927-2204 AEP-3 Expanded relay board. Provides 8 additional relay outputs to N-1000/PW-2000 panels

NEW 927-2205 ENC-0 Enclosure for the N-1000/PW2000 control panels. No battery, battery wire, lock, keys or tamper switch

NEW 927-2206 ENC-4 Enclosure for N-1000/PW2000. Includes: 8 volt battery set, battery wires, lock, keys and tamper switch

NEW 927-2208 LCK-1 Key and lock for ENC-0 enclosure

NEW 927-2418 BAT-1 8 Volt battery for N-1000-II. Replacement 8 volt operational battery backup for N-1000-II control panels

NEW 927-2419 BAT-2 3 Volt Lithium battery for N-1000-II/N-500

NEW 922-0209 BAT-3 12 Volt battery for N-1000/PW2000 series of control panels
Power Supplies
Note: The power supply listed below is for suitable locking devices only. A PSX220 transformer is required for all of the above N-1000 Series panels.
922-0056 1382N Elmdene 12V dc 2 Amp PSU, as above
PRO-2200 Control Panel Equipment & Ancillaries (For use with WIN-PAK 2005, WIN-PAK PRO,
WIN-PAK PRO 2005 & WIN-PAK PRO CS Software)

NEW 912-0328 PRO22IC Intelligent control module - supports any combination of up to 8 I/O or reader boards to monitor
alarm input points, relay output points and access control reader interface points

NEW 912-0333 PRO22R2 Dual reader module - interfaces with the Intelligent Control module (PRO22IC) providing I/O support
for 2 readers

NEW 912-0332 PRO22R1 Single reader module - interfaces with the Intelligent Control module (PRO22IC) providing I/O support
for one card reader

NEW 912-0329 PRO22IN PRO22IN provides 16 supervised inputs & 2 relay outputs.When mounted in a PRO22ENC3 one
additional relay output and two dedicated alarm inputs for cabinet tamper and power fault detection are provided

NEW 912-0331 PRO22OUT PRO22OUT provides 12 general purpose output relays when mounted in PRO22ENC1/2 & 16
are available when using the PRO22ENC3

NEW 912-0323 PRO22EN Ethernet daughter board for TCP/IP communication (For PRO2200 use only)

NEW 912-0322 PRO22CVT1 RS232 to RS485 single port converter (requires 200mA 9V dc power supply, CVT1PSU)

NEW 922-0210 CVT1PSU Linear regulated, 3-pin 13A plug top, 9V dc 200mA power supply. (For use with PRO2200CVT1)

NEW 912-0330 PRO22M4 4MB memory expansion
N1000-III-CB
PRO22IC
N1000-III
Access Control Systems
For more information about our products, please call [phone]