BEVOi INSTRUCTION MANUAL Models: BVIREF18SS BVIREF18W o o o o 5. Please read the Manual carefully before use.
Contents 1. SAFETY WARNINGS. 2. INSTALLTION.... 2.1 Location 2.2 Door Handle Install 2 2 2 ,.3 2.3 Reversing the Door Swing(optional) 2.4 Door Space Requirements 6 2.5 Leveling the Unit 6 2.6 Cleaning Before Use 6 2.7 Before Using Your Unit 2.8 Interior Accessories 2.9 Icemaker Installation 2.10 Connecting ice Maker to Water Suppiy 7 .7 7 12 3. PRODUCT OVERVIEW 14 4. OPERATION. 14 4.1 Key 14 4.2 Display Screen 14 4.3 Display 15 4.4 Shift Setting 15 .. 15 4.
2. INSTALLATION 2.1 Location When selecting a position for your unit you should make sure the floor is flat and firm, and the room is well ventilated. Avoid locating your unit near a heat source, e.g. cooker, boiler or radiator. Also avoid direct sunlight as it may increase the electrical consumption. Extreme cold ambient temperatures may also cause the unit not to perform properly. This unit is not designed for use in a garage or outdoor installation. Do not drape the unit with any covering.
1. SAFETY WARNINGS Warning: Risk of fire/flammable materials RECOMMENDATIONS: This appliance is intended to be used in household and similar applications such as staff kitchen areas in shops, offices and other working environments; farmhouses and by clients in hotels, motels and other residential type environments; bed and breakfast type environments; catering and similar non-retail applications.
2.3 Reversing The Door Swing Reversing the door position Parts included with the hinge kit: Parts already mounted on the door(as shipped): h Center right hinge Center left hinge Left top hinge cover Screws(4) Handle assembly Allen wrench Upper door self-locking block Right top hinge cover Top left hinge Upper door self-locking block Plug(4) Left door-open stopper Top right hinge Right door-open Door block stopper Bottom hinge 1.
5. Unscrew the two screws holding the bottom hinge,then remove the bottom hinge from the bottom right side of the refrigerator. 6. Unscrew the hinge pin from the right side of the bottom 9. Insert the plastic bushings into the left sides of freezer and refrigerator doors. ©^r hinge and move it to the ieft side, then secure the bottom hinge to the bottom left side of the refrigerator, using the screws you removed previously.
12. Remove the right upper door self-locking block and the right door-open stopper. Store in a safe place in case you need to reverse the door position again. 13. Remove the two hole caps from the left side, where the center hinge will go, and insert them into the other side. 14. Attach the refrigerator door on the bottom hinge,then attach the center left hinge to the left side of the refrigerator. Attach the left center hinge 15.
17. Remove the four Phillips* head screws from the left side of the door. 18. Screw the four Phiiiips* head screws into the holes on the right side of the door. 19. Attach the handles to the right sides of doors with the Allen-head screws you just removed. Tighten with the Aiien wrench and repiace the screw caps. 2.4 Door Space Requirements The unit's door must be able to open fully as shown. W>50.8 inch, D>58.5 inch Q 2.
2.7 Before Using Your Unit The refrigerator adopts 115V/60HZ AC power, voltage fluctuations over the range of 98 ~ 132V will cause malfunction or even damage. Do not damage the power cord under any condition so as to ensure safety use, do not use when t m V the power cord is damaged or the plug is worn. Do not put flammable, explosive, volatile and highly corrosive items in the refrigerator to prevent damages to the product or fire accidents.
The copper tubing and shut off valve are available In a kit from your local hardware or plumbing supply store. Coil enough tubing at the back of the unit to aliow movementfor cleaning. Unplug the refrigerator.To eliminate the danger of electric shock during installation, i'l you must unplug the refrigerator from its electrical outlet. »l 1. Ice Maker 4.Screws - Qty 2 2. Ice Container 3. Plastic Water Supply Tubing 6. Leveling Bracket Screw - Qty 1 5. Screws-Qty 2 7. Leveling Bracket Qtyl 8.
1. Unplug refrigerator from wall outlet. 2. Remove ice tray rack from freezer. 3. The frozen shelf moved to the next partition. 4. Remove plugs from inside freezer compartment with putty knife. O \ 5. Peel off label covering ice maker hole. RamowUbal ^ 6. With needle nose pliers, remove foam from hole. Remove and Discan} ■> 7. I Push water Inlet tube into small hole on back of refrigerator. Rotate while inserting tube until flat surface of inlet tube is tight against back of refrigerator. 8.
(11) Water Inlet Tube (3)Water Tubing—. 9. Install adjustable leveling bracket(7) on bottom of ice maker with screw (6). DO NOT tighten bracket.(Bracket wili be tightened iater.) Leveing Bracket(7) i Screw(6) 10. start two, iong, ice maker mounting screws (5) into freezer wail. Turn each screw five turns clockwise. (Mice Maker Mountng Screw6 11. With ice maker in one hand, plug ice maker connector into connector mounted on top freezer panel. Make sure connection is tight.
. Adjust leveling bracket(7)to level Ice maker (1). Ice maker is level when gap between freezer wall and ice maker is same at top and bottom. Tighten screw (6) when levei. »-T!» ■(1)ke Maker (6) Screw (7) Bracket 14. Reinstaii freezer sheif in lower position. Set ice container (2) on shelf. T /l^(2)k» Container 15. Locate factory punched holes at bottom right corner of rear panel. Holes are only drilled through cabinet liner. Align water valve bracket with factory drilled holes.
Water Valve (10) m NybnNul Plastic Water ■TubtnB{3) Tokematwr PH Tube 18. Secure plastic water tubing to rear of cabinet with two piastic clamps (9). NOTE: Clean back of cabinet with a commercial household cleaner, ammonia or alcohol before applying clamps. (9) Plastic aarap 2.10 Connecting Ice Maker To Water Supply Unplug the refrigerator. To eliminate the danger of electric shock during installation, you must unplug the refrigerator from its electrical outlet.
4. Slide brass compression nut,then ferrule (sleeve), onto water supply line, as shown. 5. Push water supply line into water valve inlet as far as it will go(1/4 Inch). Slide ferrule (sleeve)into valve inlet and finger tighten compression nut onto valve. Tighten another haif turn with a wrench; DO NOT over tighten. 6. With steel clamp and screw, secure water supply line to rear panei of refrigerator at iocation as shown. 7.
3. PRODUCT OVERVIEW control Salad Cover ●All images in this Instruction manual are for Indication only; please refer to your individual unit for details. 4. OPERATION HMI and keys operation The keys in HMI and display layout are referred in the following figure: A ® @(D @(D ® \ 1 Temperatuiv ConbX)l J 3 3 r”*T” SET 4.1 Key A. ©Temperature setting button of refrigerator compartment. 4.
5. CLEANING 5.1 Defrosting Auto-defrost for Frost-free Refrigerator. 5.2 Cleaning the Interior and the Exterior of the Unit ● Remove all the shelves and the salad bin. To remove the salad bin first remove the lower door shelf. ● Wipe the inside of the unit with a weak solution of bicarbonate soda and then rinse with warm water using a wrung-out sponge or cloth. Wipe completely dry before replacing the shelves and salad bin.
4.3 Display ● Once initially powered on,the display screen (including the key light) is on fuil dispiay for 3s, and then operates as the dispiayed middle shift. ● Normai operation display In case of a failure, the appropriate LED light show in combination the faiiure code (in recycling display); In case of no failures,the actual operation position of refrigerator will be on display. 4.4 Shift setting Each time the shift setting key A is pressed once,the shift position changes one time.
7. Troubleshooting The following simple issues can be handled by the user. Please call the after-sale service department if the issues are not settled. Whether the freezer Is plugged and connected to power; Inoperation Low voltage; Failure power or tripping circuit. Odorous foods should closely wrapped; Odor Whether foods are rotten; Whether the interior shall be cleaned.
