E88820-00 HF14 14” Upright Vacuum with HEPA Filter Operator and Parts Manual 1001 Brown Avenue • Toledo, Ohio 43607-0127 Customer Service: 888-GO-BETCO • Fax: 800-445-5056 • Technical Service: 877-856-5954 • www.betco.
TABLE OF CONTENTS TECHNICAL INFORMATION ........................................... 3 GENERAL SAFETY INFORMATION ...........................4 - 5 MACHINE PREPARATION AND OPERATION ............6 - 7 MAINTENANCE .........................................................8 - 9 MACHINE DIAGRAM AND PARTS LISTING ..........10 - 13 WIRING DIAGRAM....................................................... 14 WARRANTY .................................................................
TECHNICAL DESCRIPTION Measurement Unit HF14 Vacuum Motor Power Watts 1000 Brush Motor Power Watts 250 Dust Bag Capacity Gallons 1.2 Working Surface Inches 14 Weight Lbs.
GENERAL SAFETY INFORMATION PACKAGING • The box and packaging materials have been designed to protect the appliance during shipping and are biodegradable and recyclable. Please dispose of these items as you would any other product that can be recycled. USED VACUUM CLEANER • The symbols for the materials used to manufacture parts and accessories, and the recycle symbols, are located on the parts themselves, where there is room to do so.
GENERAL SAFETY INFORMATION • Only wipe the appliance clean with a dry (or very slightly damp) cloth while it is unplugged. Never place the appliance in water. • Never clean up anything that is burning or smoking, such as cigarettes, matches, hot ash, etc. • Never place any items in the appliance openings. Never use the vacuum cleaner with openings blocked in any way; keep them free from dust, dirt, hair and anything else that might reduce air flow. • Do not clean up toner powder.
MACHINE PREPARATION AND OPERATION 1 1 Ergonomic handgrip 2 Power cable 3 Hose 4 Telescopic extension 5 Switch 6 Carrying handle 7 Cord Wrap Hooks 8 Hatch 9 Air vent 7 2 4 3 5 6 8 7 9 10 Motor housing 10 11 Electric brush 12 Base 11 2. CONNECTING THE HOSE Insert the straight coupling into the dust bag container hole: insert the angled coupling into the side slot of the motor housing. 3.
MACHINE PREPARATION AND OPERATION 4. STARTING UP THE BRUSH To operate: Use your foot to press the cover (A) and lower the cleaner at the same time. A 5. CHECKING THE BRUSH The brush control device constantly checks the brush operation: • Green light: the brush is operating correctly Red light: the brush is blocked or subject to excessive stresses. Switch off the cleaner, remove the mains plug and check the cause of the blockage. • Simultaneous red and green lights: roller worn out: to be replaced. 6.
MAINTENANCE 1. FILTER DUST BAG REPLACEMENT Remove the hatch. Place paper bag in the container, inserting the bag support fitting into the hole in the bag and pushing the safety ring as far as it will go. If the filter bag is not correctly positioned, it will not be possible to close the hatch. 2. FILTER REPLACEMENT Take out the filter support and replace it or clean it by tapping it gently (the filter needs to be replaced about every 20 dust bags). 3.
MAINTENANCE 4. REMOVING OBSTRUCTIONS FROM THE EXTERNAL HOSE • Obstructions can be removed from the hose by sliding the hose out from its seating and starting up the suction function but blocking it intermittently with your hand. • Do not insert any items to remove obstructions from the pipe. 5. REMOVING OBSTRUCTIONS FROM THE INTERNAL HOSE • • • • Disconnect power. Put the suction unit in a horizontal position in line with the electric brush. Remove the screws from the base: remove the base.
BASE SPARE PARTS DIAGRAM 10
BASE SPARE PARTS LISTING Item # Part # Description Item # Part # Description 1 E22020 Lower Base 14 E22061 Screw, M3 x 20, Phps Pan Head Tapping 2 E22060 Screw, M4.2 x 16, Zinc Phps 15 E22062 Screw, M3.5 x 16, Phps Pan Head Tapping 3 E88929 Roller Brush Assembly 16 E88931 Microswitch 4 E88928 Belt, Brush Drive 17 E22062 Screw, M3.
VACUUM BODY PARTS DIAGRAM 12
VACUUM BODY PARTS LISTING Item# Part # Description Item# Part # Description 1 E22034 Housing, Vac Motor 28 E88936 Prefilter, HEPA 2 E22065 Screw, M4 x 40, Phps Pan Head Tapping 29 E22045 Protection, HEPA Filter 3 E22035 Cover, Rear Vac Bag 30 E22067 Screw, M3.
WIRING DIAGRAM CAUTION! Any job involving the electric equipment must be carried out by qualified personnel only.
BETCO US WARRANTY POLICY 10 year coverage 3 Year Coverage 1 Year Coverage Subject to the conditions stated below, Betco warrants parts and labor on rotationally molded polyethylene tanks/ housings and injection molded vacuum head assemblies to be free from defects in materials and workmanship for a period of ten years to the original purchaser.
