Quick Assembly Guide - BESV LX1 Quick Assembly Guide BESV LX1 V. 1.0, Jan.
Quick Assembly Guide - BESV LX1 Contents 1. 2. What’s in the Box ......................................................................................................................................... 2 1.1 Main Box Contents .......................................................................................................................... 2 1.2 Accessory Box Contents ................................................................................................................
Quick Assembly Guide - BESV LX1 1. What’s in the Box 3 1.1 Main Box Contents 5 1. Main Bike Assembly 2. Accessory Box 3. Saddle/Seat Post Set 4 4. Front Wheel 1 5. Front Fender 2 1.2 Accessory Box Contents 1. Product Documentation 2. Charger 3. Pedals 5. 2 3 4. Rear Light & Reflector Quick Release (QR) for the 5 Front Wheel 6. Key 7.
Quick Assembly Guide - BESV LX1 2. Assembly Procedures 2.1 Front Wheel 2.1.1 Unpack the front wheel and the main bike assembly. 2.1.2 Insert the wheel into the fork end. Attention: The disk should be placed between the brake pads.
Quick Assembly Guide - BESV LX1 2.1.3 Set the quick release (QR) Unscrew the nut and spring from the QR and insert the QR stem from the left side of the bike. Attention: The quick release handle should be on the left side of bike. 2.1.4 Tighten the nut Place the spring back in the QR stem and tighten the nut until you encounter resistance. Then loosen 1/4 turn。 Note: The tapered end of the spring should be facing inward. 2.1.
Quick Assembly Guide - BESV LX1 2.2 Front Fender and Reflector 2 1 2.2.1 Fender parts introduction 1. Front Fender & Support 2. Fix Plate*2 3. M5 Screw*2 4. Front Reflector 3 5. Fender screw with washers 4 5 2.2.2 Place the fix plate at the bottom of the front fork and loosely secure with the M5 screw. 2.2.3 Place front fender and support with the end of the support going into the fix plate. 2.2.
Quick Assembly Guide - BESV LX1 2.3 Pedal 2.3.1 Take out the pedal. 2.3.2 Set up the right pedal R Note: There is a mark “R” on one of the pedal. Assemble it onto the right crank clockwise. 2.3.3 Set up the left pedal L Take another pedal and assemble it to the left crank counterclockwise.
Quick Assembly Guide - BESV LX1 2.4 Battery 2.4.1 Insert the key and turn it to the “OPEN” position. 2.4.2 Pull the battery cover upward. 2.4.3 Slide the battery in and push it until it firmly connects to the socket. 2.4.4 Close the battery cover. Push the key in and turn it to “OFF” position to lock the battery cover in place.
Quick Assembly Guide - BESV LX1 2.5 Saddle & Seat Post 2.5.1 Open the seat post clamp and insert the seat post。 Attention: the depth of the seat post. The seat post must be inserted at least 10cm (3.9inch). 10cm (3.9 inch) 2.5.2 Set the saddle face forward and adjust the height. Lock the seat post clamp.
Quick Assembly Guide - BESV LX1 2.6 Rear Light 2.6.1 Introduction of the rear light parts. 2 1. Rear light 4 2. Bracket upper housing. 3. Bracket lower housing & reflector 4. M4 Nut*2 5. M4*L15 Screw*2 1 3 5 2.6.2 Bracket. Put the M4 nut into bracket upper housing. Set under the saddle. 2.6.3 Combine upper and lower housing by M4 nut. 2.6.4 Insert the rear light into the bracket rail.
Quick Assembly Guide - BESV LX1 3 Checklist 3.1 Check the tire pressure is normal. 3.2 Check the function of the brakes, derailleur, and chain. 3.3 Check the function of the electric module and the battery power. Please refer to LX1 user manual.
