Quick Assembly Guide - BESV JS1 Quick Assembly Guide BESV JS1 JS1 V. 1.0, April.
Quick Assembly Guide - BESV JS1 Contents 1. 2. 3 What’s in the Box .......................................................................................................................... 2 1.1 Main Box Contents ............................................................................................................. 2 1.2 Accessory Box Contents .................................................................................................... 3 Assembly Procedures ............................
Quick Assembly Guide - BESV JS1 What’s in the Box 1.1 Main Box Contents 1. Main Bike Assembly 2. Accessory Box 3. Saddle/Seat Post Set 4. Front Wheel 5.
Quick Assembly Guide - BESV JS1 1.2 Accessory Box Contents 1. Product Documentation 2. Charger 3. Pedals 4. Rear Light & Reflector 5. Quick Release (QR) for the Front Wheel 6. Key 7. Front reflector 8. Screw sets for Reflector and Front Fender 9. Front Fender 10.
Quick Assembly Guide - BESV JS1 Assembly Procedures 2.1 Front Wheel 2.1.1 Unpack the front wheel and the main bike assembly. 2.1.2 Insert the wheel into the fork end. Attention: The disk should be placed between the brake pads. Use the inner knob fine tuning.
Quick Assembly Guide - BESV JS1 2.1.3 Set the quick release (QR) Unscrew the nut and spring from the QR and insert the QR stem from the left side of the bike. Attention: The quick release handle should be on the left side of bike. 2.1.4 Tighten the nut Place the spring back in the QR stem and tighten the nut until you encounter resistance. Then loosen 1/4 turn。 Note: The tapered end of the spring should be facing inward. 2.1.
Quick Assembly Guide - BESV JS1 6
Quick Assembly Guide - BESV JS1 2.2 Front Fender and Reflector Place the fix plate at the bottom of the front fork and loosely secure with the 2-M5 screws. 2.2.1 Place 2-M5 screws go through front fender support and insert Front Fork M5 screw holes fixed. 2.2.2 Place the front reflector at the top of the fork where the fender meets the fork, then loosely secure with the fender screw.
Quick Assembly Guide - BESV JS1 2.2.3 Adjust the fender to top position, and then tighten the screws at the reflector and at the fix plate. Suggest Front Tire pressure is 60psi. Note: When securing the reflector to the fork, make sure the placement order is fork, fender and then reflector.
Quick Assembly Guide - BESV JS1 2.3 Pedal 2.3.1 Take out the pedal. 2.3.2 Set up the right pedal Note: There is a mark “R” on one of the pedal. Assemble it onto the right crank clockwise. 2.3.3 Set up the left pedal Take another pedal and assemble it to the left crank counterclockwise.
Quick Assembly Guide - BESV JS1 2.4 Battery 2.4.1 Insert the key and turn it to the “OPEN” position. 2.4.2 Slide the battery in and push it until it firmly connects to the socket. 2.4.3 Close the battery cover. Push the key in and turn it to “OFF” position to lock the battery cover in place. While turn to “ON” (red test), the HMI monitor will appearance function.
Quick Assembly Guide - BESV JS1 2.5 Saddle & Seat Post 2.5.1 Screw released the seat post clamp and adjust the height. Lock the seat post clamp. Attention: Please don’t let cable go inside seat post. 2.
Quick Assembly Guide - BESV JS1 1. Rear Light 2. Bracket 3. M5 Screw 4. M5 Spring Washer 5. M5 Nut x2 (Thin) 6. Base Support 7. Top Clip 8. M5 x 35 Screw 9. M5 Nut (Thick) 10. M4 Screw with Plastic Knob 11. Spring 12. Gear Washer 13. M4 Nut 2.6.1 Bracket. Put the 2-M5 nut fix bracket and rear light. 2.6.2 Combine Support and Rear Light housing by gear washer/spring/M4 screw.
Quick Assembly Guide - BESV JS1 2.6.3 Combine Clip and Rear right by M6 screw. 2.6.4 Upper and lower clip fixed on seat bow by M5 screw. 2.6.5 The Rear Light cable should around the clip above and go connecting terminals. Attention: The cable surface has white lines, Please put into Rear Light negative “–“terminal(left terminal(left side). side).
Quick Assembly Guide - BESV JS1 3 Checklist 3.1 Check the tire pressure is normal. 3.2 Check the function of the brakes, derailleur, and chain. 3.3 Check the function of the electric module and the battery power. Please refer to JS1 user manual.
