Installation Manual

ManualsBrandsBestop ManualsAutomotiveBestop 80028-15 Black Denim Windjammer Wind Break for 1980-1995 CJ-5, CJ-7 & Wrangler

80028 pg 1

Rev. B 0204

Windjammer

Installation Instructions

For: CJ7, ’80-’86 and Wrangler

Part Number: 80028

WARNING

This product is designed to enhance the appearance of

the vehicle. Do not rely in any way on the components of this

product to contain occupants or cargo within the vehicle, or

to protect against injury or death in the event of an accident.

This top will not protect the occupants from falling objects.

Never operate vehicle in excess of manufacturer’s specifi-

cations.

WEAR SEAT BELTS AT ALL TIMES

Read and follow, precisely, all installation instructions pro-

vided when installing top. Failure to do so may result in a poor

fitting top and could place occupants of the vehicle in a

potentially dangerous situation.

Installation Tips

Before you begin installing this Windjammer assembly,

read all instructions thoroughly. Below are a few tips to

make this installation easier.

For a smooth fit:

For ease in installation, the Windjammer should be

installed at temperatures above 72° F. Below this

temperature, the fabric may contract an inch or

more, making it difficult to fit to the vehicle.

It is normal for the fabric to contract and wrinkle when

stored in the shipping carton. Within a few days after

the installation, the fabric will relax and the wrinkles will

disappear.

Important Note: Windjammer is custom designed to attach to the leading edge of

Bestop’s Duster Rear Deck Cover, which covers folded soft top bow assemblies. If the

installation of the Windjammer and Duster Deck Cover is being performed on an

original equipment hardtop vehicle, an extension flap may be required. If this flap is

not present in the Duster package, it may be obtained from Bestop.

Summary of content (5 pages)

PAGE 1
Windjammer Installation Instructions For: CJ7, ’80-’86 and Wrangler Part Number: 80028 Important Note: Windjammer is custom designed to attach to the leading edge of Bestop’s Duster Rear Deck Cover, which covers folded soft top bow assemblies. If the installation of the Windjammer and Duster Deck Cover is being performed on an original equipment hardtop vehicle, an extension flap may be required. If this flap is not present in the Duster package, it may be obtained from Bestop.
PAGE 2
Parts List and Hardware Identification Windjammer Fabric "Z" Channel, 5" "Z" Channel, 17" Qty - 1 Qty - 2 Qty - 1 Tools Needed #8 x 1" Pan Head Screw, Qty - 7, Part Number 295.95 #20 Torx Snap Head Screw, Qty - 3, Part Number 200.49 1/8" Drill Bit and Drill Motor Phillips Screwdriver Pencil Acorn Locknut, Qty - 3, Part Number 293.94 Windjammer Installation Step One Fold the front seats forward and locate the three pieces of "Z" Channel in the parts kit.
PAGE 3
Step Two Orient the Windjammer with the window toward the top and with the vinyl side out, toward the rear of the vehicle. Start with the top straps and thread the end of each strap through each buckle. Loosely tighten each strap around the sport bar to hold the Windjammer in position.
PAGE 4
If You Have a Bestop Duster Rear Deck Cover on Your Vehicle Windjammer - From Rear Step One Locate the flap sewn to the rear of the Windjammer. Pull the flap out over the top of the front edge of the Duster.
PAGE 5
Care and Maintenance of your New Windjammer Your Windjammer is made of the finest materials available. To keep it looking new and for the maximum possible wear, it will need periodic cleaning and maintenance. Washing: The fabric should be washed often using soap, warm water and a soft bristle brush. Rinse with clear water to remove all traces of soap. Windows: Keep windows clean to avoid scratching. DO NOT use a brush on the windows! Wash with a watersoaked cloth or sponge and a mild dishwashing detergent.