User manual

ManualsBrandsBESTip ManualsComputer equipmentATA 10D

BESTip ATA Combo

VoIP Gateway

User Manual

Projectek Networking Electronics Corp.

Mar. 2009

BESTip ATA Combo User Manual

This publication may not be reproduced, in whole or in part,

without prior expressed written permission from Projectek

Projectek Networking Electronics Corp. makes no warranties

with respect to the contents hereof and specifically disclaims

any implied warranties of merchantability or fitness for any

particular purpose. Furthermore, Projectek Networking

Electronics Corp. reserves the right to revise this publication

and to make changes from time to time in the content hereof

without obligation to notify any person or organization of such

revisions or changes.

Trademarks

BESTip. is the trademark of Projectek Networking Electronics Corp.

All other trademaks mentioned herein are the properties of their

respective owners.

Projectek Networking Electronics Corp.

5F-9, No. 16, Lane 609, Sec. 5, Chung Hsin Road,

San Chung, Taipei Hsien, Taiwan, R.O.C.

TEL: (886) 2-2278-7067 Fax: (886) 2-2278-7094

Technical Support: BESTip #: 800123#

http://www.iptelcom.com.tw

Summary of content (25 pages)

PAGE 1
BESTip ATA Combo User Manual Copyright Notice This publication may not be reproduced, in whole or in part, without prior expressed written permission from Projectek Networking Electronics Corp. All rights reserved. Copyright © 2009, by Projectek Networking Electronics Corp. Projectek Networking Electronics Corp. makes no warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
PAGE 2
BESTip ATA Combo User Manual Please fill in the following ID no. which you can find it on the bottom of your BESTip ATA Combo. You may need it in the future. Purchase Date: BESTip ATA Combo User Manual Table of Contents Chapter 1: Overview .......................................................................6 Physical Description ..........................................................8 (1 year warranty) ID no: Chapter 2: Installation ...............................................................
PAGE 3
BESTip ATA Combo User Manual Voice Codec ....................................................................48 Software/ Hardware .........................................................48 Physical ...........................................................................
PAGE 4
BESTip ATA Combo User Manual BESTip ATA Combo User Manual Supporting multiple telephony interfaces This manual gives you easy-to-follow instructions for installing and using the BESTip ATA Combo. The BESTip ATA Combo supports 1 analog FXS port for connecting to an existing analog telephone or other analog terminal and an Ethernet & Dial-up interface for connecting to a home or office Local Area Network.
PAGE 5
BESTip ATA Combo User Manual Rear Panel BESTip ATA Combo User Manual Chapter 2: Installation There are four connectors on the rear panel to connect to the related devices. The description is listed below (left to right). This chapter will describe how to connect your BESTip ATA Combo. Package Contents The package of the BESTip includes the following: DC 12V PHONE LINE LAN DC 12V DC Adapter Connector: connects to the 12V DC power adapter.
PAGE 6
BESTip ATA Combo User Manual Physical Installation BESTip ATA Combo User Manual Chapter 3: Setup Follow the instructions for correct connection: 1. After connection, follow the easy instructions to setup the BESTip ATA Combo. You can establish your setup or modify it at any time by launching the BESTip. Connect one end of an RJ-11 phone cord to the Phone connector on the back of BESTip ATA Combo. Connect the other end to the analog phone sets or C.O ports of the PBX. 2.
PAGE 7
BESTip ATA Combo User Manual 1. You can press “DOWN” button at standby status to enter main menu. BESTip ATA Combo User Manual 3. There are different options in the Function Select menu for Broad & Dial-up mode. The options will be described in the following sections. Press “Down” button to enter main menu. (Dial-Up Mode) 2. Then, you can press “NEXT” or “BACK” button to scroll the menu. Press “NEXT” button to scroll the menu. (Broadband Mode) Press “BACK” button to scroll the menu.
PAGE 8
BESTip ATA Combo User Manual 4. You can press “UP” button to return to standby status. BESTip ATA Combo User Manual 2. Press “NEXT” or “BACK” button to select “Quick Setting” menu. Press “UP” button to return to standby status. Press “NEXT” or “BACK” button to scroll the menu. 3. Press “DOWN” button to enter “Quick Setting” menu. Using Buttons to Setup BESTip You can use the buttons on the front panel of the BESTip and your telephone keypads to setup the BESTip.
PAGE 9
BESTip ATA Combo User Manual 5. To input “Country Code”, press “OK” firstly and the title will start flashing. Then you are able to input data. BESTip ATA Combo User Manual 7. You can also use the keypad on the touchtone phone to input the necessary data. Remember to pick up the phone handset while using the phone keypad to input data. Please refer to the Typical Phone Keypad and Configuration Sheet below to enter character.
PAGE 10
BESTip ATA Combo User Manual 9. After finishing all the settings, please press “UP” button one or two times until the screen displays “Update Setup” as following picture. All the setting will be saved permanently. BESTip ATA Combo User Manual Switch Between Broadband and Dial-up Mode Before configuring your BESTip ATA Combo, you have to switch between broadband or dial-up mode to fit your Internet Connection. 1. Press button to enter the Function Select Mode.
PAGE 11
BESTip ATA Combo User Manual BESTip ATA Combo User Manual 9. ISP IdleTimeout : This mode allows auto disconnection from the Internet when no action detected continues a period of time. 0 means always online. 10. Country Code: Please enter your country code. Function Select－Quick Setting (Dial-Up Mode) You can always set the data of the device in the Quick Setting menu. 1. Press to enter the Function Select Mode. Press button to enter Quick Setting. 2.
PAGE 12
BESTip ATA Combo User Manual Function Select－Recharge Credit (Dial-Up Mode) BESTip ATA Combo User Manual Function Select－System Info (Dial-Up Mode) You may top up your ITSP account with recharge card. Please ask local distributor for more detail. You can always consult the system information of your ATA in the System Info menu. 1. Press to enter the Function Select Mode. Press or to scroll the main menu till it appears System Info. And then press to enter the option.
PAGE 13
BESTip ATA Combo User Manual BESTip ATA Combo User Manual 3. Area Code: Please enter the local Area Code. 13. Show CDR: CDR will be shown on the display after call finished if you turn it on. 4. IDD Prefix: Please enter the International Direct Dial code. 14. Polarity Reverse: Normally set to “OFF” unless your device is applied for business purpose. 5. 2nd IDD Prefix: Please enter the secondary International Direct Dial code. Leave it blank unless you are in USA. 6.
PAGE 14
BESTip ATA Combo User Manual BESTip ATA Combo User Manual 3. Enter the ISP phone number. Press to save. 3. Pick up your handset. Modify the ISP name. Press to save. 4. Enter the login name. Press to save. 4. Modify the ISP phone number. Press to save. 5. Enter the login password. Press to save. 5. Modify your login name. Press to save. 6. Press or selcet the PPP type. Press save. to 6. Modify the login password. Press to save. to 7. Enter the primary DNS. Press to save. 7. Use or the PPP type.
PAGE 15
BESTip ATA Combo User Manual 2. Press or to select your target ISP name. Press to save and back to the upper menu. BESTip ATA Combo User Manual Factory Setting－Clear System Setup 1. Press to enter the option. 2. Press setup. to clear system User Profile－Erase 1. Press or to scroll the menu till it appears Erase. And press to enter the option. Factory Setting－Clear Phone Book 2. Press or to select the ISP you want to erase. Press to confirm and back to the upper menu.
PAGE 16
BESTip ATA Combo User Manual BESTip ATA Combo User Manual BESTip can be upgraded whenever a new software version becomes available. Upgrades can enhance the performance and add more features to your BESTip. 6. It will take about 5 minutes to finish downloading depending on the network traffic. If the new software version is downloaded successfully, BESTip will reboot itself automatically. Note: Before proceeding to upgrade, be sure that your BESTip is connected to the Internet.
PAGE 17
BESTip ATA Combo User Manual BESTip ATA Combo User Manual 8. ROUTER Adress: It will display the Router/ Gateway IP address. Function Select－System Info (Broadband Mode) You can always get the system information for your BESTip from the System Info menu. 1. Press button to enter the Function Select Mode. Press button to enter System Info. 9. Primary DNS Address: It will display the primary DNS address. 2. Device ID: Each BESTip device has an unique 8 digit ID#.
PAGE 18
BESTip ATA Combo User Manual BESTip ATA Combo User Manual IP Policy－DHCP DHCP: Dynamic Host Configuration Protocol is a method for assigning IP address and other IP parameters to computers on the IP network in a single message with great flexibility. IP addresses can be static or temporary depending on the needs of the network. 1. Press button to enter the Function Select Mode. 2. Press or button to scroll the main menu till it appears Function Select - System Setting. And then press to enter the option.
PAGE 19
BESTip ATA Combo User Manual IP Policy－Static IP BESTip ATA Combo User Manual IP Policy－ADSL PPPoE If you select Static IP mode, please consult your ISP or MIS to have the information listed below. Please use the keypad on your phone or the buttons on BESTip to input the information obtained. 1. Press button to enter the Function Select Mode. 1. Press button to enter the Function Select Mode. 2. Press or button to scroll the main menu till it appears Function Select - System Setting.
PAGE 20
BESTip ATA Combo User Manual BESTip ATA Combo User Manual 7. DDD Prefix: Please key in the Domestic Direct Dial prefix code. “0” in most cases. Other Common Setup (Broadband Mode) After selecting and configuring the IP Policy, you need to continue to set the following parameters. Remember to press button to effect the setting and go to the next option. 8. Direct City Call: Normally set to “OFF”. 1. Station ID: The default value is 1.
PAGE 21
BESTip ATA Combo User Manual BESTip ATA Combo User Manual 1. Press button to enter the Function Select Mode. Function Select－Factory Setting (Broadband Mode) BESTip has the auto-recovery capability. Just follow the steps below to restore the factory settings. 2. Press or button to scroll the main menu till it appears Function Select - System Upgrade. And then press to enter the option. Note: Before proceeding to restoring, be sure that your BESTip is connected to the Internet. 1.
PAGE 22
BESTip ATA Combo User Manual BESTip ATA Combo User Manual 2. Once the system testing finishes, it will go for standby status. Chapter 4: To Make an Internet Call After having finished the setup in Chapter 3, you are ready to operate your BESTip. Refer to the illustration below to connect your BESTip with other devices. 3. Please press to dial ISP to establish Internet connection.
PAGE 23
BESTip ATA Combo User Manual displayed is counted from 00:00:00, it means your BESTip is not successfully registered to the Gatekeeper and your network connection or configuration might be incorrect. Please refer to “Chapter 3: Setup” in this manual for network configuration. BESTip ATA Combo User Manual To Make a BESTip-to-Phone Call With Internet Telephony Service Provider (ITSP) service function ready, BESTip is able to call any real telephone around the world.
PAGE 24
BESTip ATA Combo User Manual To Receive a BESTip Call BESTip ATA Combo User Manual Appendix A: Specifications Once your BESTip is connected to the Internet, you may accept the calls from other BESTip devices. You cannot receive calls only when you are in the BESTip Setup mode. Interface Telephone Interface RJ-11 ports, 1x FXS for phone set LAN Interface RJ-45 port, 10/100M Ethernet 2 LED, 100/10 and LINK/ACT Line Interface RJ-11 port, FXO for bulit-in 33.
PAGE 25
BESTip ATA Combo User Manual WAN Interface Front Control Panel Built-in 33.6K Analog Modem 16 characters x 2 Lines LCD, 5 Push Button Switches Operating System Embedded Real-Time Operating System Networking Protocol IP, TCP, UDP, PPP, PAP, CHAP, PPPoE, DNS Configure BESTip ATA 10D Front Panel through front panel. No additional Self-Configuration function software or hardware required Voice Over IP Gateway Protocol BESTip Gateway Protocols Only 10k bps bandwidth is required when using G.723.1 6.