INSTRUCTION MANUAL 28-Inch Wicker Fire Pit Table Ver.
IF YOU SMELL GAS • Do not attempt to light appliance. • Extinguish flames and disconnect tank. • Move people away from the immediate area. bestchoiceproducts.
NOTICE • • • • • • • • • • • • • • Please retain these instructions for future reference. For outdoor use only; do not use in a building, garage, or any other enclosed area. Fire pit operates at reduced efficiency in temperatures below 40°F or wind velocity higher than 10 mph. Only use this appliance on a hard and level surface such as concrete or rock. Do not use on plastic composite or artificial wood decks. Fire pit can be used with a propane tank or natural gas tank.
PROPANE TANK WARNINGS • Make sure to organize fuel hose to prevent accidental tripping. • Only use standard 20-pound propane tanks. • Maximum gas supply pressure is 250 PSI. • Do not fill tank more than 80% of its capacity. • Do not use tank if any part of it is damaged; rust and dents can be dangerous. • Propane tank must have a collar to protect the gas valve. • Using too much propane gas may result in gas pooling and will not burn.
PARTS A B LID 1 PC D BACK PANEL E 1 PC LEFT PANEL RIGHT PANEL 1 PC F TANK SEAT FRAME 1 PC H DOOR C 1 PC 1 PC G TABLETOP WITH BURNER GLASS BEADS 1 SET 1 PC I COVER 1 PC |5
PRODUCT ASSEMBLY 1 Attach part D back panel to part C left panel with two part 3 screws and two part 1 washers. 1 x2 3 x2 D C 2 Attach part F tank seat frame with two part 3 screws and two part 1 washers.
PRODUCT ASSEMBLY 3 Attach part E right panel with four part 3 screws and four part 1 washers.
PRODUCT ASSEMBLY 4 8| Insert the part G door into the designated holes and secure with the magnetic catches.
PRODUCT ASSEMBLY 5 Carefully flip the table base over and attach it to the part B tabletop with six part 2 screws and six part 1 washers. 2 x6 1 x6 B 6 Place the part H glass beads (see Placing Glass Beads section).
PRODUCT ASSEMBLY 7 Place the part A lid. Hang lid on hangers when not in use.
DIAGRAM GUARD BURNER HANGERS REGULATOR FUEL HOSE CONTROL PANEL COUPLING NUT PLACING GLASS BEADS • Place glass beads in fire pit and spread them according to your preference. - You may place glass beads around the burner but do NOT cover the guard. • Excessive glass beads will suffocate the flame.
INSTALLING PROPANE TANK 1 NOTE: Only use standard 20-pound propane tanks. Pull handle and remove door. Place propane tank on the tank seat frame. Turn wingnut clockwise to secure tank. Make sure release valve on tank is firmly screwed shut. 2 12 | Attach fuel hose regulator to the output of the tank by turning the coupling nut clockwise. - If door does not close, adjust position of tank and hose until door closes. 3 Turn release valve on tank counterclockwise to release gas.
CONTROL PANEL IGNITE CONTROL KNOB IGNITER: Push to light burner HIGH OPERATING INSTRUCTIONS NOTE: Before use, inspect burner, propane tank, and connectors for damage, debris, obstructions, or dirt. Do not operate if there is any blockage. 1. Push and turn control knob counterclockwise to low/ignite. 2. Press the ignitor button repeatedly to light burner. - If flames do not ignite after 45 seconds, turn off, wait 5 minutes, and try again.
CLEANING • Make sure fire pit is completely cool before cleaning or storage. • Use a soft brush or cloth to wipe stains and dirt. • If necessary, clean with mild detergent and a soft cloth/sponge. • Black soot may develop on glass beads after use; use a damp cloth to clean debris as needed. • Thoroughly dry fire pit after cleaning. • Do not submerge control panel or burner assembly in water. • Do not use petroleum-based or abrasive cleaners as it may damage the finish.
TROUBLESHOOTING PROBLEM Burner not lighting with igniter Burner does not light Emits a lot of black smoke REASON SOLUTION Guard obstructed Clear guard of obstructions Burner wet Dry burner Igniter battery dead Replace battery in igniter Propane tank is empty Replace/refill tank Coupling nut loose Fully tighten coupling nut Bent hose Straighten hose Burner holes obstructed Remove obstructions or clean holes Control knob off Turn control knob on Bent hose Straighten hose Burner holes o
HELP CENTER Question about your product? We're here to help. Visit us at: help.bestchoiceproducts.com CHAT US! Product Assembly Returns & Refunds PRODUCT WARRANTY INFORMATION All items can be returned for any reason within 60 days of the receipt and will receive a full refund as long as the item is returned in its original product packaging and all accessories from its original shipment are included. All returned items will receive a full refund back to the original payment method.
