User Manual
Table Of Contents
- Contents
- ENGLISH
- IMPORTANT SAFETY INSTRUCTIONS
- Features
- Tools needed
- Package contents
- Installation instructions
- STEP 1 - Determine whether your TV has a flat back or an irregular or obstructed back
- STEP 2 - Select screws, washers, and spacers
- STEP 3 - Attach the mounting hardware to a TV
- STEP 4 - Determine the wall-mount location
- STEP 5 - Option 1: Install on a wood stud wall
- STEP 5 - Option 2: Install on a solid concrete or concrete block wall
- STEP 5 - Option 3: Install on a steel stud wall
- STEP 6 - Securing your TV to the wall plate
- Managing cables
- Adjusting the position of your TV
- Removing your TV from the wall plate
- ONE-YEAR LIMITED WARRANTY
- ESPAÑOL
- INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- Características
- Herramientas requeridas
- Contenido del paquete
- Instrucciones de instalación
- PASO 1 - Determine si su televisor tiene una parte posterior plana, irregular u obstruida
- PASO 2 - Selección de los tornillos, arandelas y espaciadores
- PASO 3 - Como fijar la ferretería de montaje a un televisor
- PASO 4 - Determine la ubicación del montaje en pared
- PASO 5: Opción 1: Instale en una pared con viga de madera
- PASO 5: Opción 2: Instalación en una pared de concreto sólido o de bloques de concreto
- PASO 5 - Opción 3: Instalación en una pared con vigas de acero
- PASO 6 - Fijación del televisor a la placa para pared
- Organización de cables
- Ajuste de la posición de su televisor
- Cómo quitar el televisor de la placa de pared
- GARANTÍA LIMITADA DE UN AÑO
17
Large Extended Tilt Mount for 32"-70" TVs/Montaje con inclinación extendido grande para televisores de 32 a 70 pulg.
www.bestbuy.com/bestbuyessentials
STEP 5 - Option 3: Install on a steel stud wall
You’ll need
1 Align the center of the wall plate template at the height (a + b) you determined in the previous step, make sure that it is
level, then tape it to the wall.
Note: Steel stud installation kit not included. See Package contents on page 5 for information about how to recieve this kit free of
charge.
CAUTIONS:
• Studs must be at least 2 x 4 in./25 gauge.
• If the back side of the wall is unfinished, drywall must be installed to a minimum of one stud left and right of the stud(s) being used
to install the TV mount.
• Drywall must be a minimum of 1/2 in. (13 mm) thick on each side of the studs, and a minimum clearance of 1 in. (25 mm) behind the
wall is required.
• Pilot holes MUST be drilled to a depth of 1 in. (25 mm), using a 1/2 in. (13 mm.) diameter drill bit.
• Steel stud anchors must be centered on the studs.
• Stud type and structural strength must conform to the North American Specification for the Design of Cold-Formed Steel Structural
Members [362 S 125 18, C-Shape, S - Stud Section].
• Drywall must be secured to studs with screws 12 in. (304.8 mm) on center.
1/2 in.
masonry drill
bit
Hammer
Socket wrench
Drill
Edge-to edge
stud finder
Tape
1/4-20 x 1-3/4 in screw (4)
Level
Pencil
Wall plate template
1/4 in. washer (4)
Wall plate
Awl
1/4-20 Snap Toggle BB (4)
Minimum 16 in.
(406 mm)