Technical information
Table Of Contents

4 – PARAMETERS
28
4.1 Introduction
The MX incorporates a large number of parameters that allow you to configure the starter to meet the special requirements of your
particular application. The parameters are organized two ways, depending on the display being used. When the standard, on-board
LED display is used, the parameters are in a single group and numbered P1, P2, P3… etc.
When the remote LCD display is used, the parameters are divided into groups of related functionality, and within the groups the
parameters are identified by a short, descriptive name. They are numbered by the group name followed by an index within the group.
This chapter lists all of the parameters and their possible values. Section 4.3 lists the parameters in the order in which they appear on
the LED display. Section 4.4 lists them in the order in which they appear on the LCD display. The following table is a cross-
reference between the two.
4.2 LED and LCD Display Parameters Cross Reference
Parameter
Number
Group Page
#
Parameter
Number
Group Page
#
P1 QST 01 Motor FLA 41 P3 PFN 14 Motor Running Overload Class 42
P2 QST 02 Motor Service Factor 41 P37 PFN 15 Motor Overload Hot/Cold
Ratio
67
P3 QST 03 Motor Running Overload Class 42 P38 PFN 16 Motor Overload Cooling Time 68
P4 QST 04 Local Source 43 P39 I/O 01 DI 1 Configuration 69
P5 QST 05 Remote Source 44 P40 I/O 02 DI 2 Configuration 69
P6 QST 06 Initial Current 1 45 P41 I/O 03 DI 3 Configuration 69
P7 QST 07 Maximum Current 1 46 P42 I/O 04 R1 Configuration 70
P8 QST 08 Ramp Time 1 47 P43 I/O 05 R2 Configuration 70
P9 QST 09 Up To Speed Time 48 P44 I/O 06 R3 Configuration 70
P10 CFN 01 Start Mode 49 P45 I/O 07 Analog Input Trip Type 71
P8 CFN 02 Ramp Time 1 47 P46 I/O 08 Analog Input Trip Level 72
P6 CFN 03 Initial Current 1 45 P47 I/O 09 Analog Input Trip Time 72
P7 CFN 04 Maximum Current 1 46 P48 I/O 10 Analog Input Span 73
P11 CFN 08 Initial Voltage/Torque/Power 50 P49 I/O 11 Analog Input Offset 74
P12 CFN 09 Maximum Torque/Power 51 P50 I/O 12 Analog Output Function 74
P13 CFN 10 Kick Level 1 52 P51 I/O 13 Analog Output Span 75
P14 CFN 11 Kick Time 1 52 P52 I/O 14 Analog Output Offset 75
P15 CFN 14 Stop Mode 53 P53 I/O 15 Inline Configuration 76
P16 CFN 15 Decel Begin Level 54 P54 I/O 16 Bypass Feedback Time 76
P17 CFN 16 Decel End Level 55 P55 I/O 17 Keypad Stop Disable 77
P18 CFN 17 Decel Time 56 P56 PFN 17 Reserved
P19 CFN 06 Initial Current 2 56 P57 PFN 18 Reserved
P20 CFN 07 Maximum Current 2 57 P58 FUN 15 Miscellaneous Commands 78
P21 CFN 05 Ramp Time 2 57 P59 FUN 12 Communication Timeout 78
P22 CFN 12 Kick Level 2 57 P60 FUN 11 Communication Baud Rate 79
P23 CFN 13 Kick Time 2 58 P61 FUN 10 Communication Drop Number 79
P24 PFN 01 Over Current Level 58 P62 FUN 09 Energy Saver 79
P25 PFN 02 Over Current Time 59 P63 FUN 08 Heater Level 80
P26 PFN 03 Under Current Level 60 P64 FUN 07 Starter Type 81
P27 PFN 04 Under Current Time 60 P65 FUN 06 Rated Power Factor 82
P28 PFN 05 Current Imbalance Level 61 P66 FUN 05 Rated Voltage 82
P29 PFN 06 Ground Fault Level 62 P67 FUN 04 Phase Order 83
P30 PFN 07 Over Voltage Level 63 P68 FUN 03 CT Ratio 83
P31 PFN 08 Under Voltage Level 63 P69 FUN 01 Meter 84
P32 PFN 09 Voltage Trip Time 64 NA FUN 02 Meter 2 84
P33 PFN 10 Auto Reset 64 P70 FUN 13 Starter Model Number 84
P34 PFN 11 Controlled Fault Stop Enable 64 P71 FUN 14 Software Part Number 85
P35 PFN 12 Independent Starting/Running
Overload
65 P72 FUN 16 Passcode 86
P36 PFN 13 Motor Starting Overload Class 66 P73 FL1 Fault Log 87