TK700STi Projector RS232 Command Control Installation Guide
Table of Contents Introduction ............................................................................................................................................. 3 Wire arrangement........................................................................................................................................................ 3 RS232 pin assignment .................................................................................................................................................
Introduction The document describes how to control your BenQ projector via RS232 from a computer. Follow the procedures to complete the connection and settings first, and refer to the command table for RS232 commands. Available functions and commands vary by model. Check the specifications and user manual of the purchased projector for product functions.
Connections and communication settings Choose one of the connections and set up properly before RS232 control. RS232 serial port with a crossover cable D-Sub 9 pin (male) on a projector PC or laptop D-Sub 9 pin (female) Communication cable (crossover) Settings On-screen images in this document are for reference only. The screens may vary depending on your Operating System, I/O ports used for connection, and the specifications of the connected projector. 1.
2. Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected. 3. Finish Serial port setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Check the baud rate of the connected projector from its OSD menu.
RS232 via LAN RJ45 port on a projector PC or laptop LAN cable Settings 1. Find the Wired LAN IP address of the connected projector from the OSD menu and make sure the projector and the computer are within the same network. 2. Input 8000 in the TCP port # field. RS232 via HDBaseT HDBaseT compatible device D-Sub 9 pin RJ45 port on a projector RJ45 PC or laptop D-Sub 9 pin LAN cable Settings 1. Determine the COM Port name used for the RS232 communications in Device Manager. 2.
3. Finish Serial port setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Check the baud rate of the connected projector from its OSD menu.
Command table • Available features differ by projector specification, input sources, settings, etc.. • Commands are working if the standby power is 0.5W or a supported baud rate of the projector is set. • Uppercase, lowercase, and a mixture of both types of characters are accepted for a command. • If a command format is illegal, it will echo Illegal format. • If a command with correct format is not valid for the projector model, it will echo Unsupported item.
Audio source select Picture Mode Write Volume level for customer *vol=value# YES Read Volume Status *vol=?# YES Write Mic. Volume + *micvol=+# NO Write Mic. Volume - *micvol=-# NO Read Mic.
Write HLG *appmod=hlg# NO Read Picture Mode *appmod=?# YES Write Contrast + *con=+# NO Write Contrast - *con=-# NO Write Set Contrast value *con=value# YES Read Contrast value *con=?# YES Write Brightness + *bri=+# YES Write Brightness - *bri=-# YES Write Set Brightness value *bri=value# YES Read Brightness value *bri=?# YES Write Color + *color=+# NO Write Color - *color
Write Aspect Anamorphic *asp=ANAM# NO Write Aspect Anamorphic 2.35 *asp=ANAM2.
Operation Settings Write 4 Corners Bottom-Right-Y Increase *cornerfitbry=+# NO Read 4 Corners Bottom-Right-Y Status *cornerfitbry=?# NO Write Digital Zoom In *zoomI# NO Write Digital Zoom out *zoomO# NO Write Auto *auto# NO Write Brilliant color on *BC=on# YES Write Brilliant color off *BC=off# YES Read Brilliant color status *BC=?# YES Write Auto(HDR) *hdr=auto# NO Write SDR *hdr=sdr# NO
Read Signal Power On-Status *autopower=?# NO Write Standby Settings-Network on *standbynet=on# NO Write Standby Settings-Network off *standbynet=off# NO Read Standby Settings-Network Status *standbynet=?# NO Write Standby Settings-Microphone on *standbymic=on# NO Write Standby Settings-Microphone off *standbymic=off# NO Read Standby Settings-Microphone Status *standbymic=?# NO Write Standby Settings-Monitor Out on *stan
Read Ballast F/W Version *ballastfwversion=?# NO Write Blank On *blank=on# YES Write Blank Off *blank=off# YES Read Blank Status *blank=?# YES Write Freeze On *freeze=on# YES Write Freeze Off *freeze=off# YES Read Freeze Status *freeze=?# YES Write Menu On *menu=on# YES Write Menu Off *menu=off# YES Read Menu Status *menu=?# YES Write Up *up# YES Write Down *down# YE
Installation Read Remote Receiver Status *rr=?# NO Write Instant On-on *ins=on# NO Write Instant On-off *ins=off# NO Read Instant On Status *ins=?# NO Write Lamp Saver Mode-on *lpsaver=on# NO Write Lamp Saver Mode-off *lpsaver=off# NO Read Lamp Saver Mode Status *lpsaver=?# NO Write Projection Log In Code on *prjlogincode=on# NO Write Projection Log In Code off *prjlogincode=off# NO Read Projection
Write save Lens memory 8 *lenssave=m8# NO Write save Lens memory 9 *lenssave=m9# NO Write save Lens memory 10 *lenssave=m10# NO Write Reset Lens to center *lensreset=center# NO Write Tint + *tint=+# NO Write Tint - *tint=-# NO Write Set Tint value *tint=value# NO Read Get Tint value *tint=?# NO Write Set BenQ gamma value *gamma=value# YES Read Gamma value status *gamma=?# YES Write Set HD
Write Hue + *hue=+# NO Write Hue - *hue=-# NO Write Set Hue value *hue=value# YES Read Get Hue value *hue=?# YES Write Saturation + *saturation =+# NO Write Saturation - *saturation =-# NO Write Set Saturation value *saturation =value# YES Read Get Saturation value *saturation =?# YES Write Gain + *gain=+# NO Write Gain - *gain=-# NO Write Set Gain value *gain=value# YES Read
BenQ.com © 2018 BenQ Corporation All rights reserved. Rights of modification reserved. Version: 1.
