MP724/MP727/MP735 Digital Projector User Manual Welcome Downloaded from ProjectorsManual.
English Table of contents Important safety instructions .......................3 Introduction......................7 Projector features ................................. 7 Shipping contents................................. 8 Projector exterior view......................... 9 Controls and functions ....................... 10 Positioning your projector14 Choosing a location............................ 14 Obtaining a preferred projected image size........................................... 15 Connection ...
English Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. Please read this manual before you operate your projector. Save it for future reference. 2. Do not look straight at the projector lens during operation.
English Safety Instructions (Continued) 7. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement. 10. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage. 8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions. 11.
English Safety Instructions (Continued) 13. Do not place this projector in any of the following environments. 14. Do not block the ventilation holes. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector. - Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.
English Safety Instructions (Continued) 17. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury. 18. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call BenQ to have the projector serviced. 19.
English Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features.
English Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated.
Front/upper side 1 5 6 2 3 1. 2. 3. 4. 5. 6. 7. 8. Vent (heated air exhaust) Lamp cover Quick-release button Projection lens External control panel (See "Projector" on page 10 for details.) Vent (cool air intake) Focus ring and Zoom ring Front IR remote sensor 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. AC power cord inlet USB input socket D-SUB output socket D-SUB/COMP.
English Controls and functions Projector 6. MODE/ENTER Selects an available picture setup mode. See "Selecting a picture mode" on page 39 for details. Enacts the selected On-Screen Display (OSD) menu item. See "Using the menus" on page 29 for details. 7. Left/ Starts the FAQ function. See "Utilizing FAQ function" on page 45 for details. BLANK Used to hide the screen picture. See "Hiding the image" on page 44 for details. FOCUS/ZOOM Ring Used to adjust the projected image appearance.
1 2 15 15 16 16 2 17 18 3 4 17 18 3 4 19 19 5 6 7 20 5 6 7 20 8 21 8 21 9 22 9 22 10 23 10 23 11 24 11 24 12 12 25 25 13 26 13 26 14 27 14 27 28 28 For Japan model only Standard remote 1. Laser (Standard Remote only) Use as on-screen pointer. DO NOT POINT IN EYES. 2. POWER Toggles the projector between standby mode and on. See "Starting up the projector" on page 28 and "Shutting down the projector" on page 48 for details.
English 11. 12. 13. 14. 15. 16. 17. 18. STATUS Opens the OSD STATUS menu (the menu only opens when an input device is detected). MENU Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings. See "Using the menus" on page 29 for details. AUTO Automatically determines the best picture timings for the displayed image. See "Auto-adjusting the image" on page 34 for details. SOURCE Displays the source selection bar.
Remote control effective range English Infra-Red (IR) remote control sensor is located on the front of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 7 meters (~ 23 feet). App r ox.
English Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of four possible installation locations: 1.
English Obtaining a preferred projected image size The distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in the projected image size. 4:3 is the native aspect ratio of MP724 and MP727. 16:10 is the native aspect ratio of MP735. To be able to project a complete 16:9 (widescreen) aspect ratio image on MP724 or MP727, the projector can resize and scale a widescreen image to the projector's native aspect width.
English How to determine the position of the projector for a given screen size 1. 2. Select your screen size. Refer to the table and find the closest match to your screen size in the left columns labelled "4:3 screen". Using this value, look across this row to the right to find the corresponding average distance from screen value in the column labelled "Average". This is the projection distance. 3. On that same row, look across to the right column and make note of the "Vertical offset in mm" value.
English MP724/727 projection dimensions Refer to "Dimensions" on page 66 for the center of lens dimensions of this projector before calculating the appropriate position. Maximum zoom Minimum zoom Screen Center of lens Vertical offset Projection distance MP724 Recommended projection distance from screen in mm 4:3 screen diagonal Width Height Min length Average Max length (with min. zoom) Vertical offset in mm Feet Inches mm mm mm (with max.
MP727 English Recommended projection distance from screen in mm 4:3 screen diagonal Width Height Min length Average Max length Vertical offset in mm Feet Inches mm mm mm (with max.
English MP735 projection dimensions Refer to "Dimensions" on page 66 for the center of lens dimensions of this projector before calculating the appropriate position. Maximum zoom Minimum zoom Screen Center of lens Vertical offset Projection distance 16:10 screen diagonal Width Height Recommended projection distance from screen in mm Min Max length length Average Feet Inches mm mm mm (with max.
English Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores.
English Connecting a monitor If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the D-SUB OUT signal output socket on the projector to an external monitor with a VGA or VGA to DVI-A cable by following the instructions below. To connect the projector to a monitor: • With a VGA cable: • With a VGA to DVI-A cable: Your monitor must be equipped with a DVI input socket. 1. 2. 3.
English Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: • HDMI • DVI-I • Component Video • S-Video • Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
English Connecting HDMI source devices The projector provides a HDMI input socket that allows you to connect it to a HDMI source device like a DVD player, a DTV tuner or a display. HDMI (High-Definition Multimedia Interface) supports uncompressed video data transmission between compatible devices like DTV tuners, DVD players and displays over a single cable. It provides pure digital viewing and listening experience.
English Connecting DVI-I source devices The projector provides a DVI-I input socket that allows you to connect it to a DVI-I source device like a DVD player. DVI-I format is used to directly carry a digital signal to a digital display without signal conversion. The pure digital connection provides faster and higher image quality than an analog connection, due to the nature of the digital format.
English Connecting Component Video source devices Examine your Video source device to determine if it has a set of unused Component Video output sockets available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a Component Video source device: 1.
English Connecting S-Video source devices Examine your Video source device to determine if it has an unused S-Video output socket available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device. 2.
English Connecting Composite Video source devices Examine your Video source device to determine if it has a set of unused composite Video output sockets available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. Take a Video cable and connect one end to the composite Video output socket of the Video source device. 2.
English Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. 2. Press POWER on the projector or remote control to start the projector and a start up tone sounds. The POWER indicator light flashes green and stays green when the projector is on. The start up procedure takes about 30 seconds.
English Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. Below is the overview of the OSD menu. Main menu icon Main menu Off Wall Color Auto Aspect Ratio Keystone Highlight Position Sub-menu Status ENTER Phase 15 H. Size 0 Press MENU/ EXIT to the previous page or to exit. Digital Zoom Current input signal Analog RGB MENU Exit To use the OSD menus, please set them to your familiar language first. 1.
English Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 29. You will be inconvenienced if you activate the power-on lock functionality and subsequently forget the password.
English If you forget the password If the password function is activated, you will be asked to enter the five-digit password every time you turn on Password Error the projector. If you enter the wrong password, the Please try again. password error message as pictured to the right displays lasting for three seconds, and the message 'INPUT PASSWORD' follows.
English Disabling the password function To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Change Security Settings menu after opening the OSD menu system. Press MODE/ENTER. The message 'INPUT PASSWORD' displays. Enter the current password. i. If the password is correct, the OSD menu returns to the Security Settings page. Press to highlight Power on Lock and press / to select Off. You will not have to enter the password next time you turn on the projector.
English Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SOURCE menu is On (which is the default of this projector) if you want the projector to automatically search for the signals. You can also manually cycle through the available input signals. 1. 2. • Press SOURCE on the projector or remote control. A source selection bar displays.
English Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position. 2. Screw the rear adjuster foot to fine tune the horizontal angle.
1. English Fine-tuning the image size and clarity Adjust the projected image to the size that you need using the ZOOM ring. FOCUS ZOOM 2. Then sharpen the image by rotating the FOCUS ring. FOCUS ZOOM Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.
English Magnifying and searching for details If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture. • Using the remote control 1. Press Zoom +/- to display the Zoom bar. 2. Press Zoom + to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need. 3. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. 4.
English Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. For MP724 and MP727, the default aspect ratio is 4:3. And for MP735, the default aspect ration is 16:10. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.
2. Real: English The image is projected as its original resolution, and resized to fit within the display area. For input signals with lower resolutions, the projected image will display smaller than if resized to full screen. You could adjust the zoom setting or move the projector away from the screen to increase the image size if necessary. You may also need to refocus the projector after making these adjustments.
English Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select an operation mode that suits your need, you can follow one of the following steps. • • Press MODE/ENTER on the projector repeatedly until your desired mode is selected. Go to the PICTURE > Picture Mode menu and press / to select a desired mode.
Setting the User 1/User 2 mode English There are two user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the User 1/User 2) as a starting point and customize the settings. 1. 2. 3. 4. Press MENU/EXIT to open the On-Screen Display (OSD) menu. Go to the PICTURE > Picture Mode menu. Press / to select User 1 to User 2. Press to highlight Reference Mode.
Adjusting Color / English Highlight Color in the PICTURE menu and adjust the values by pressing projector or remote control. on the Lower setting produces less saturated colors. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic. Adjusting Tint Highlight Tint in the PICTURE menu and adjust the values by pressing projector or remote control. / on the The higher the value, the more reddish the picture becomes.
3D Color Management English In most installation situations, color management will not be necessary, such as in classroom, meeting room, or lounge room situations where lights remain on, or where building external windows allow daylight into the room. Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered.
English Setting the presentation timer The presentation timer can indicate the presentation Presentation Timer 15 Timer period time on the screen to help you achieve better time Always Timer display management when giving presentations. Follow these Timer position Top-Left Timer counting direction Count Down steps to utilize this function: Sound reminder Off Off 1. Go to the SYSTEM SETUP: Basic > On Back Presentation Timer menu and press MODE/ ENTER to display the Presentation Timer page. 2.
3. English Highlight Yes and press MODE/ENTER to confirm. You will see the message “Timer is Off” displaying on the screen. Remote paging operations Connect the projector to your PC or notebook with a USB cable prior to using the paging function. See "Connecting a computer" on page 20 for details. You can operate your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint) by pressing PAGE / on the remote control.
English Locking control keys With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is on, no control keys on the projector will operate except POWER. 1. 2. / on the projector or go to the SYSTEM SETUP: Basic > Panel Key Lock menu, and select Press On by pressing / on the projector or remote control. A confirmation message displays. Select Yes to confirm.
English Operating in a high altitude environment We recommend you use the High Altitude Mode when your environment is between 1500 m –3000 m above sea level, and temperature is between 5°C–23°C. Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature is between 5°C and 28°C. The projector will be over cooled, if you turn the mode on under such a condition. To activate the High Altitude Mode: Notice 1.
English Adjusting the sound The sound adjustments made as below will have an effect on the projector speakers. Be sure you have made a correct connection to the projector audio input. See "Connection" on page 20 for how the audio input is connected.
English Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • • • • Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame.
English Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. Main menu 1. DISPLAY Sub-menu Options Wall Color Off/Light Yellow/Pink/Light Green/Blue/Blackboard Aspect Ratio Auto/Real/4:3/16:9 Keystone Position Phase H.
English FAQ-Image and Installation FAQ-Features and Service 6. INFORMATI Current System Status ON Timer period Presentation Timer • • • • • Source Picture Mode Resolution Color System Equivalent Lamp Hour 1~240 minutes Timer display Always/1 min/2 min/3 min/Never Timer position Top-Left/Bottom-Left/Top-Right/ Bottom-Right Timer counting direction Count Down/Count Up Sound reminder On/Off On/Off 4.
Off/On Quick Cooling Audio Settings Menu Settings 5.
English Description of each menu FUNCTION (default setting/ value) DESCRIPTION (default setting/value) Wall Color Corrects the projected picture’s color when the projection surface is not white. See "Using Wall Color" on page 40 for details. (Off) Aspect Ratio (Auto) Keystone 1. DISPLAY menu (0) Position (0) Phase (depends on the selected input signal) There are four options to set the image's aspect ratio depending on your input signal source.
English FUNCTION (default setting/ value) Tint (0) 2. PICTURE menu Sharpness (15) DESCRIPTION (default setting/value) Adjusts the red and green color tones of the image. See "Adjusting Tint" on page 41 for details. The function is only available when Video or S-Video with NTSC system is selected. Adjusts the image to make it look sharper or softer. See "Adjusting Sharpness" on page 41 for details. Brilliant Color Adjusts white peaking while maintaining correct color presentation.
English FUNCTION (default setting/ value) DESCRIPTION (default setting/value) Projector Position The projector can be installed on a ceiling or behind a screen, or with one or more mirrors. See "Choosing a location" on page 14 for details. (Front Table) 4. SYSTEM SETUP: Basic menu Auto Power Off Allows the projector to turn off automatically if no input signal is detected after a set period of time. See "Setting Auto Power Off" on page 58 for details.
English FUNCTION (default setting/ value) Standby DSub Output (Off) DESCRIPTION (default setting/value) Selecting On enables the function. The projector can output a VGA signal when it is in standby mode and the D-SUB IN and D-SUB OUT sockets are correctly connected to devices. See "Connecting a monitor" on page 21 for how to make the connection. Enabling this function slightly increases the standby power consumption. Lamp Mode (Normal) See "Setting Lamp mode as Economic" on page 58 for details. 5.
English FUNCTION (default setting/ value) DESCRIPTION (default setting/value) FAQ-Image and Installation Displays possible solutions to problems you may encounter. 6. INFORMATION menu FAQFeatures and Service Source Shows the current signal source. Picture Mode Shows the selected mode in the PICTURE menu. Current System Status Resolution Shows the native resolution of the input signal. Color System Shows input system format, NTSC, PAL, SECAM, or RGB.
English Maintenance Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust.
English Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows: Total (equivalent) lamp hour = 1 (hours used in Economic mode) + 3/2 (hours used in normal mode) See "Setting Lamp mode as Economic" below for more information on Economic mode. To obtain the lamp hour information: 1.
English Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes.
English Replacing the lamp • If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by fractured lamp. • To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
5. • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 6. Insert the new lamp into the lamp compartment and make sure it fits in the projector.
Press the lamp cover down until the click is heard locking the projector. 11. Restart the projector. English 10. Do not turn the power on with the lamp cover removed. Resetting the lamp timer 12. After the startup logo, open the On-Screen Notice Display (OSD) menu. Go to the SYSTEM Reset Lamp Timer? SETUP: Advanced > Lamp Settings menu. Press MODE/ENTER. The Lamp Reset Cancel Settings page displays. Press to highlight Reset lamp timer and press MODE/ENTER.
Light Power English Indicators Status & Description Temp Lamp Power events Orange Off Off Stand-by mode Green Flashing Off Off Powering up Green Off Off Normal operation Orange Flashing Off Off The projector needs to cool for 90 seconds after the power is turned off. Lamp events Orange Flashing Off Red The lamp ignition retries if the lamp fails during startup. Off Off Red 1. 2. The projector needs 90 seconds to cool down. Or Please contact your dealer for assistance.
English Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cable. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
English Specifications Projector specifications All specifications are subject to change without notice. General Product name Model name Digital Projector MP724 MP727 MP735 Resolution 1024 x 768 XGA 1024 x 768 XGA 1280 x 800 WXGA Display system 1-CHIP DMD F = 2.55 to 2.72, f = 21.3 to 24.5 mm 280 W lamp F = 2.6 to 2.81, F = 2.55 to 2.71, f = 26.01 to 29.84 mm f = 21.33 to 24.
English Dimensions 325 mm (W) x 95 mm (H) x 254 mm (D) 325 254 95 58.6 80.53 Timing chart Supported timing for Analog RGB input Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 31.469 59.940 25.175 VGA_60 37.861 72.809 31.500 VGA_72 37.500 75.000 31.500 VGA_75 43.269 85.008 36.000 VGA_85 37.927 85.039 35.5 720 x 400 x 85 35.2 56.3 36 SVGA_56 37.879 60.317 40.000 SVGA_60 48.077 72.188 50.000 SVGA_72 46.875 75.000 49.
Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 49.7 59.8 83.5 WXGA_60 62.8 74.9 106.5 WXGA_75 71.554 84.880 122.500 WXGA_85 63.981 60.020 108.000 SXGA3_60 79.976 75.025 135.000 SXGA3_75 91.146 85.024 157.500 SXGA3_85 1440 x 900 55.935 59.887 106.500 WXGA+_60 1400 x 1050 65.317 59.978 121.750 SXGA+_60 1600 x 1200 75.000 60.000 162.000 UXGA 640 x 480@67Hz 35.000 66.667 30.240 MAC13 832 x 624@75Hz 49.722 74.546 57.
• English Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration. Supported timing for Video and S-Video inputs Video mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Color sub-carrier Frequency (MHz) NTSC 15.73 60 3.58 PAL 15.63 50 4.43 SECAM 15.63 50 4.25 or 4.41 PAL-M 15.73 60 3.58 PAL-N 15.63 50 3.58 PAL-60 15.73 60 4.43 NTSC4.43 15.73 60 4.
Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 48.363 60.004 65.000 XGA_60 56.476 70.069 75.000 XGA_70 60.023 75.029 78.750 XGA_75 68.667 84.997 94.500 XGA_85 49.7 59.8 83.5 WXGA_60 62.8 74.9 106.5 WXGA_75 71.554 84.880 122.500 WXGA_85 63.981 60.020 108.000 SXGA_60 79.976 75.025 135.000 SXGA_75 91.146 85.024 157.500 SXGA_85 1440 x 900 55.935 59.887 106.500 WXGA+_60 1400 x 1050 65.317 59.978 121.750 SXGA+_60 1600 x 1200 75.
English Warranty and Copyright information Limited warranty BenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).
English Regulation statements FCC statement CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.